Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ EGR Cooler)
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0388653 ECD SYSTEM(w/ EGR Cooler) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  Black Smoke Emitted  


DESCRIPTION

Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Intake System
Symptom and Corresponding Main Fault
·

Lack of power (no black smoke) due to air cleaner filter element blockage or crushed or leaking air duct

·

Black smoke (no lack of power) due to leakage between the turbocharger and intake manifold


Data List Intake Manifold Absolute Pressure

Glow System
Main fault Glow system malfunction
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Diagnostic Point
·

Measure the resistance of the glow plug assembly

·

Check the glow plug assembly indicator light



Engine
Main fault Loss of compression
Symptoms Rough idle (lack of power always)
Data List Engine Speed of Cylinder
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.


Injection Feedback Value
·

When an Injector Feedback Value is more than 5 mm3/st, there may be a malfunction in the corresponding cylinder.




b.

Diesel Injection

Fuel Supply Pump Assembly
Main fault -
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Pressure (High), Target Fuel Pressure (High)
·

Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High) during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).

·

If the fuel pressure is 20000 kPag below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPag, then idling will be rough.


HINT:

The fuel pressure changes at engine start, but is approx. 25000 kPag at engine start after the engine is warmed up.


Diagnostic Trouble Code Even if Fuel Pressure (High) is below Target Fuel Pressure (High), a DTC will not be stored.

Injector Assembly
Main fault Blockage, increase in fuel injection volume
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Value
·

When an Injector Feedback Value is more than 5 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.



HINT:
·

When the sliding resistance of the internal parts of the injector assemblies has increased due to internal contamination, injection quantity will increase at high common rail pressure due to a delay in injector assembly closure.

·

When black smoke occurs due to contamination of the injector assemblies, there are usually other symptoms, such as engine knocking noise at cold idling, rough idling, difficulty starting, etc., which are also present when the common rail pressure is low.



Fuel Pressure Sensor
Main fault Open circuit, decrease in performance (foreign matter is stuck)
Symptoms Difficult to start, rough idle, engine stall, lack of power
Data List Fuel Pressure (High), Target Fuel Pressure (High)
·

Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Fuel Pressure (High) follows Target Fuel Pressure (High). If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Fuel Pressure (High) decreases to a value less than Target Fuel Pressure (High)).


Diagnostic Trouble Code When the fuel pressure sensor has a fault, some DTCs may be stored.

Irregular Fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)


c.

Diesel EGR

EGR System
Main fault
·

Does not move smoothly

·

Does not close completely


Symptoms
·

Rough idle

·

EGR valve stuck closed: A loud turbocharger sound.

·

EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).


Data List Actual EGR Valve Position No.1, Target EGR Valve Position No.1
·

Generally, Actual EGR Valve Position No.1 = Target EGR Valve Position No.1 +/-5% (fully closed: 0%, fully open: 100%).

·

Using the EGR valve Active Test, check whether Actual EGR Valve Position No.1 follows Target EGR Valve Position No.1 (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).

·

EGR valve is fully closed when the ignition switch is turned to ON (engine stopped).

·

EGR valve opens to the halfway point at idling after the engine is warmed up.


EGR Close Learning Value Bank 1
·

When leaving the vehicle idling, the normal range of EGR Close Learning Value Bank 1 is 0 to 1 V.

·

In cases when EGR Close Learning Value Bank 1 is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.




d.

Diesel Throttle

Diesel Throttle System
Main fault Stuck, does not move smoothly
Symptoms
·

Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.

·

Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.


Data List Actual Throttle Position Bank 1
·

0%: Fully closed

·

100%: Fully open

·

When the ignition switch is ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily.





Data List Related to Black Smoke


·

Engine Speed

·

Intake Manifold Absolute Pressure

·

Mass Air Flow Sensor

·

Intake Air Temperature

·

Coolant Temperature

·

Engine Speed Cylinder #1 to #4

(Output only when the "Check the Cylinder Compression" Active Test is performed)

·

Target Fuel Pressure (High)

·

Fuel Pressure (High)

·

Injection Feedback Value #1 to #4

·

Target Injection Volume

·

Actual Throttle Position Bank 1

·

Target EGR Valve Position No.1

·

Actual EGR Valve Position No.1

·

EGR Close Learning Value Bank 1



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>REGISTRATION).



HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle to be normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


Explanation of Symptom


Black Smoke The fuel used in diesel engines has a higher boiling point and evaporates much slower than that used in gasoline engines. Additionally, the fuel is injected directly, so the air fuel mixture in diesel engines is formed in a very short period of time and is less homogenous. This is why diesel engines must operate with a larger air fuel ratio across the entire operating range. An insufficient quantity of air results in imperfect combustion and increased particulate (soot) emissions.
When the accelerator pedal is depressed, a large amount of fuel is injected. As a result, the air fuel ratio becomes rich. In this relatively rich environment, fuel droplets lacking in oxygen burn imperfectly producing soot, which is emitted as black smoke. In order to prevent black smoke production, the maximum injection quantity for a given intake air mass is limited (final injection quantity is limited by Mass Air Flow Sensor).
Black smoke is emitted when either: 1) a lack of oxygen is present during combustion, or 2) too much fuel is injected for a given intake air mass and the air fuel ratio becomes temporarily rich.


PROCEDURE

1.READ OUTPUT DTC (RELATING TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the pending DTCs.

Result:
Result Proceed to
No DTCs are output A
Engine related DTCs are output B




A

2.CHECK FOR BLACK SMOKE

B

2.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it. [*1]


d.

Repeat the above procedure [*1] 10 times or more. [*2]


e.

Check for black smoke emission during procedures [*1] and [*2].

OK:

Black smoke is emitted less than 5 times.


HINT:
·

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.

·

If the procedure is repeated 10 times or more and black smoke stops being emitted, this probably means that the black smoke was caused by a temporary accumulation of soot which occurred when driving at low speeds, and is not a malfunction.




Result:
Proceed to
OK
NG



OK

3.RECOVERY TO NORMAL

NG

4.CHECK INTAKE SYSTEM
3.RECOVERY TO NORMAL
HINT:

If the racing procedure is repeated 10 times or more and black smoke stops being emitted, this probably means that the black smoke was caused by a temporary accumulation of soot which occurred when driving at low speeds, and is not a malfunction.


Result:
Proceed to
NEXT



NEXT

END

4.CHECK INTAKE SYSTEM
a.

Check for air leakage and blockage between the air cleaner cap and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold.

HINT:
·

Make sure that the air cleaner is not clogged and the intake and exhaust system hoses are not disconnected.

·

Check that the intercooler is not clogged with foreign matter.

·

Check that there are no disconnected, pinched or leaking hoses or pipes.

·

Check that there are no modifications made by the user.



OK:

No leakage or blockage.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTION IN ENGINE COMPARTMENT

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

5.CHECK HARNESS AND CONNECTION IN ENGINE COMPARTMENT
a.

Check the harness and connector connections of common rail system components.

OK:

The harnesses and connectors are connected securely.



Result:
Proceed to
OK
NG



OK

6.CHECK INJECTOR COMPENSATION CODE

NG

20.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK INJECTOR COMPENSATION CODE
a.

Read the injector compensation codes.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Injector Compensation
50005 372 4596
OK:

Compensation codes stored in the ECM match the compensation codes of the installed injector assemblies.



Result:
Proceed to
OK
NG



OK

7.PERFORM PILOT QUANTITY LEARNING (DETAIL)

NG

18.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
7.PERFORM PILOT QUANTITY LEARNING (DETAIL)
a.

Perform the pilot quantity learning (detail).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Pilot Quantity Learning (Detail)
50005 372 4570

Result:
Proceed to
NEXT



NEXT

8.CHECK FOR BLACK SMOKE
8.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it. [*1]


d.

Repeat the above procedure [*1] 10 times. [*2]


e.

Check for black smoke emission during procedures [*1] and [*2].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



NG

9.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (AFTER ENGINE WARMED UP) (PROCEDURE 9)

OK

END

9.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (AFTER ENGINE WARMED UP) (PROCEDURE 9)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Black Smoke.


d.

Take a snapshot of the following Data List items.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.

·

Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.




Result:
Proceed to
NEXT



NEXT

10.READ VALUE USING GTS (MASS AIR FLOW SENSOR AND INTAKE MANIFOLD ABSOLUTE PRESSURE)
10.READ VALUE USING GTS (MASS AIR FLOW SENSOR AND INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


d.

Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor and Intake Manifold Absolute Pressure.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
Intake Manifold Absolute Pressure
50003 372 215,385

e.

Take a snapshot when the engine speed is maintained at 4000 rpm with no load.


f.

Read the values of "Mass Air Flow Sensor" and "Intake Manifold Absolute Pressure" in the Data List using the snapshot review function.

Result:
Result Proceed to
Mass Air Flow Sensor 84 gm/sec or more and Intake Manifold Absolute Pressure 105 kPa or higher A
Except above B


HINT:
·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.

·

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc. Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.





A

11.CHECK SNAPSHOT (TARGET INJECTION VOLUME AND INJECTION FEEDBACK VALUE #1 TO #4)

B

37.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE BANK 1)
11.CHECK SNAPSHOT (TARGET INJECTION VOLUME AND INJECTION FEEDBACK VALUE #1 TO #4)
a.

Check Injection Feedback Value #1 to #4 and Target Injection Volume in the snapshot taken in procedure 9 when the engine was idling and at 4000 rpm with no load.

Result:
Result Proceed to
Target Injection Volume is less than 10.0 mm3/st at 4000 rpm A
Injection Feedback Value for at least one cylinder is more than +5 mm3/st B
Except above C




A

12.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

B

13.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

C

21.READ VALUE USING GTS (ATMOSPHERIC PRESSURE AND INTAKE MANIFOLD ABSOLUTE PRESSURE)
12.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies of all cylinders.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

16.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
13.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed Cylinder #1 to #4.


d.

Check the engine speed during the Active Test.

Powertrain > Engine > Active Test
Active Test Display
Check the Cylinder Compression
Data List Display
Engine Speed Cylinder #1
Engine Speed Cylinder #2
Engine Speed Cylinder #3
Engine Speed Cylinder #4
50004 372 42028 134,135,136,137
Result:
Result Proceed to
Except below A
The values of Engine Speed Cylinder #1 to #4 are within 10 rpm of each other B


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.




A

14.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

B

15.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
14.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
HINT:

Measure the compression of the cylinder that had a high speed during the Active Test "Check the Cylinder Compression".


a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

15.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

15.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

16.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
16.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

17.BLEED AIR FROM FUEL SYSTEM
17.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

18.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
18.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation code.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Injector Compensation
50005 372 4596

b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Pilot Quantity Learning
50005 372 4569

Result:
Proceed to
NEXT



NEXT

19.CHECK FOR BLACK SMOKE
19.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it. [*1]


d.

Repeat the above procedure [*1] 10 times. [*2]


e.

Check for black smoke emission during procedures [*1] and [*2].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
NEXT



NEXT

END

20.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
21.READ VALUE USING GTS (ATMOSPHERIC PRESSURE AND INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Atmospheric Pressure and Intake Manifold Absolute Pressure.

Powertrain > Engine > Data List
Tester Display
Atmospheric Pressure
Intake Manifold Absolute Pressure
50003 372 229,385

d.

Compare Intake Manifold Absolute Pressure to Atmospheric Pressure when the ignition switch is ON (engine stopped).

HINT:
·

If Intake Manifold Absolute Pressure and Atmospheric Pressure have the same value, both are normal. If there is a difference of 10 kPa (0.1 kgf/cm2, 1.5 psi) or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.

·

Standard atmospheric pressure is 101 kPa (1.0 kgf/cm2, 15 psi). For every 100 m (328 ft.) increase in elevation, pressure drops by 1 kPa (0.01 kgf/cm2, 0.1 psi). This varies by weather (high atmospheric pressure, low atmospheric pressure).



Result:
Result Proceed to
Intake Manifold Absolute Pressure and Atmospheric Pressure have same value A
Atmospheric Pressure is different from actual atmospheric pressure B
Intake Manifold Absolute Pressure is different from actual atmospheric pressure C




A

22.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)

B

25.REPLACE ECM

C

28.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
22.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Target Fuel Pressure (High) and Fuel Pressure (High).

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Fuel Pressure (High)
Fuel Pressure (High)
50004 372 42023 264,265

d.

Take a snapshot with the GTS during the Active Test.


e.

Measure the difference between the target fuel pressure (Target Fuel Pressure (High)) and the actual fuel pressure (Fuel Pressure (High)) when the "Test the Fuel Leak" Active Test is performed.

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E74
3.604,2.427 3.719,1.948 3.719,1.948 3.792,1.948 false 4.604,2.583 4.948,2.323 4.948,2.323 5.031,2.323 false 3.438,2.635 3.479,1.833 3.479,1.833 3.427,1.833 false 3.583,3.25 3.833,4.323 3.833,4.323 3.979,4.323 false 0.083,1.417 1.448,1.573 1.365,0.156 10 false Active Test Operation 0.083,0.583 1.479,0.781 1.396,0.198 10 false Engine Speed (rpm) 0.313,3.198 1.854,3.469 1.542,0.271 10 false Fuel Pressure (High) 3.802,1.865 5.74,2.031 1.938,0.167 10 false Target Fuel Pressure (High) 6.469,4.125 6.865,4.302 0.396,0.177 10 false Time 2.125,2.406 2.927,3.083 0.802,0.677 10 false Less than 10000 kPag 3,4.26 3.688,4.427 0.688,0.167 10 false 2 seconds 5.073,2.208 6.583,2.719 1.51,0.51 10 false Abnormal Fuel Pressure (High) 2.677,1.042 3.354,1.24 0.677,0.198 10 false Test Start 4.458,1.042 5.125,1.24 0.667,0.198 10 false Test Stop 5.885,1.042 6.563,1.24 0.677,0.198 10 false Test Start 2.073,1.76 3.427,2.188 1.354,0.427 10 false Normal Fuel Pressure (High) 1.646,0.271 2.021,0.438 0.375,0.167 10 false 2000 1.885,0.833 2.052,1 0.167,0.167 10 false 0 1.75,1.302 2.073,1.469 0.323,0.167 10 false ON 1.698,1.552 2.021,1.719 0.323,0.167 10 false OFF 4.021,4.25 5.948,4.708 1.927,0.458 10 false Pressure Discharge Valve Abnormal Fuel Pressure (High)

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPag (102.0 kgf/cm2, 1451 psi).


HINT:
·

"Target Fuel Pressure (High)" is the target fuel pressure controlled by the ECM.

·

"Fuel Pressure (High)" is the actual fuel pressure in common rail assembly.

·

If the pressure discharge valve mounted on the common rail assembly is malfunctioning, the actual fuel pressure may change as indicated by "Pressure Discharge Valve Abnormal Fuel Pressure (High)" in the illustration.

·

The pressure discharge valve operates to discharge fuel pressure when the internal pressure of the common rail exceeds the target fuel pressure.

·

There are 2 fuel pressure sensor circuits and both of them display the same value. If the difference between Fuel Pressure (High) exceeds 10000 kPag (102 kgf/cm2, 1451 psi) for 2 seconds or more, it is necessary to inspect or repair the wiring for the fuel pressure sensor.




Result:
Proceed to
OK
NG



OK

23.READ VALUE USING GTS (COOLANT TEMPERATURE)

NG

29.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)
23.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Soak the engine for a long time.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
OK:

Coolant Temperature is the same as the ambient temperature.


HINT:

When the engine coolant temperature is low even though the engine has been fully warmed up, or when the engine coolant temperature is high even though the engine is cold, inspect the sensor.



Result:
Proceed to
OK
NG



OK

24.READ VALUE USING GTS (INTAKE AIR TEMPERATURE AND INTAKE AIR TEMPERATURE B1S1 (TURBO))

NG

26.CHECK AND REPLACE ENGINE COOLANT TEMPERATURE SENSOR
24.READ VALUE USING GTS (INTAKE AIR TEMPERATURE AND INTAKE AIR TEMPERATURE B1S1 (TURBO))
a.

Connect the GTS to the DLC3.


b.

Soak the engine for a long time.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature and Intake Air Temperature B1S1 (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature
Intake Air Temperature B1S1 (Turbo)
50003 372 214,310
OK:

Intake Air Temperature is the same as Intake Air Temperature B1S1 (Turbo).



Result:
Proceed to
OK
NG



OK

35.CHECK FOR BLACK SMOKE

NG

27.CHECK AND REPLACE MALFUNCTIONING PARTS
25.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
26.CHECK AND REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

b.

Replace the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL

HINT:

It is only necessary to replace the part when the results of the inspection indicate a problem.



Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
27.CHECK AND REPLACE MALFUNCTIONING PARTS
a.

Inspect the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION


b.

Inspect the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


c.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:

It is only necessary to replace the part when the results of the inspection indicate a problem.



d.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL

HINT:

It is only necessary to replace the part when the results of the inspection indicate a problem.



Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
28.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
29.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)
a.

Disconnect the pre-stroke control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E102-1 (+B) - E6-3 (PCV+) Always Below 1 Ω
E102-2 (PCV) - E6-4 (PCV-) Always Below 1 Ω
E102-1 (+B) or E6-3 (PCV+) - Body ground and other terminals Always 10 kΩ or higher
E102-2 (PCV) or E6-4 (PCV-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

30.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY

NG

36.REPAIR OR REPLACE HARNESS OR CONNECTOR
30.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY
a.

Disconnect the inlet hose from the fuel supply pump assembly.


b.

Operate the priming pump and check that fuel is being supplied to the fuel supply pump assembly.

OK:

Fuel is properly supplied to the fuel supply pump assembly when the priming pump is operated.


HINT:
·

When there is a lack of fuel, the fuel pressure drops.

·

Inspect for fuel filter clogging (Check that the fuel filter is not clogged).




c.

Reconnect the inlet hose.


Result:
Proceed to
OK
NG



OK

31.REPLACE FUEL SUPPLY PUMP ASSEMBLY

NG

33.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP ASSEMBLY)
31.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

32.BLEED AIR FROM FUEL SYSTEM
32.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
33.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP ASSEMBLY)
a.

Check and replace the clogged fuel pipe.


Result:
Proceed to
NEXT



NEXT

34.BLEED AIR FROM FUEL SYSTEM
34.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
35.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it. [*1]


d.

Repeat the above procedure [*1] 10 times. [*2]


e.

Check for black smoke emission during procedures [*1] and [*2].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
NEXT



NEXT

END

36.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
37.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE BANK 1)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


c.

Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
50003 372 215

f.

Read the Mass Air Flow Sensor value displayed on the GTS while the engine is idling.


g.

Enter the following menus: Powertrain / Engine / Active Test / Activate the EGR Valve Close Bank 1 / Data List / Mass Air Flow Sensor.

Powertrain > Engine > Active Test
Active Test Display
Activate the EGR Valve Close Bank 1
Data List Display
Mass Air Flow Sensor
50004 372 71 215

h.

Read the Mass Air Flow Sensor value when the EGR valve is closed using the Active Test function.

HINT:
·

If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.

·

Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.



Result:
Active Test Result Proceed to
Activate the EGR Valve Close Bank 1:
OFF to Close
Mass Air Flow Sensor value does not change A
Mass Air Flow Sensor value changes B


NOTICE:

As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.


HINT:

The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric EGR control valve assembly or mass air flow meter sub-assembly.


Reference:
EGR Valve Condition (Opening) Measuring Condition Mass Air Flow Sensor (Reference)
Open (41%)
·

Atmospheric pressure: 101 kPa

·

Engine coolant temperature: 75°C (167°F)


3 to 7 gm/sec
Closed (0%) 10 to 21 gm/sec




A

38.READ VALUE USING GTS (ENGINE SPEED AND MASS AIR FLOW SENSOR)

B

11.CHECK SNAPSHOT (TARGET INJECTION VOLUME AND INJECTION FEEDBACK VALUE #1 TO #4)
38.READ VALUE USING GTS (ENGINE SPEED AND MASS AIR FLOW SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Mass Air Flow Sensor.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Mass Air Flow Sensor
50003 372 211,215

d.

Start the engine and read the value when 30 seconds has elapsed.

Standard:
Engine Speed Mass Air Flow Sensor
Idling
·

0.5 to 15 gm/sec (EGR on)

·

10 to 21 gm/sec (EGR off)


3000 rpm (without load)
·

43 to 89 gm/sec (EGR on)

·

72 to 117 gm/sec (EGR off)





Result:
Proceed to
OK
NG



OK

39.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EGR COOLER BYPASS)

NG

42.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
39.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EGR COOLER BYPASS)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


c.

Turn the ignition switch off and wait for 30 seconds.


d.

Start the engine and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
50003 372 215

f.

Read the Mass Air Flow Sensor value displayed on the GTS while the engine is idling.


g.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for EGR Cooler Bypass / Data List / Mass Air Flow Sensor and EGR Cooler Bypass Position.

Powertrain > Engine > Active Test
Active Test Display
Activate the VSV for EGR Cooler Bypass
Data List Display
Mass Air Flow Sensor
EGR Cooler Bypass Position
50004 372 42025 215,974
HINT:

Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.



h.

Using the Active Test function, switch the EGR cooler bypass valve between "Cooler" and "Bypass" a few times, and then check whether the Mass Air Flow Sensor value changes after switching the valve from "Cooler" to "Bypass".

HINT:
·

If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.

·

When operating "Activate the VSV for EGR Cooler Bypass", check that "Cooler" and "Bypass" can be switched between and the EGR cooler by-pass valve regulating link operates. If the link does not operate, the inspection cannot be performed correctly. Therefore, inspect and repair the following parts, perform the Active Test and read the changes in the Mass Air Flow Sensor value.

- No. 2 EGR valve assembly

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

- Vacuum hose connection

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

- Vacuum switching valve assembly (for EGR Bypass Valve)

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>INSPECTION



Result:
GTS Display Result Proceed to
Activate the VSV for EGR Cooler Bypass:
Cooler to Bypass
Mass Air Flow Sensor value does not change A
Mass Air Flow Sensor value changes B


HINT:

If the EGR cooler is clogged, the mass air flow changes.




A

40.CHECK FOR DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)

B

41.REPLACE NO. 1 EGR COOLER
40.CHECK FOR DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
a.

Remove the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>REMOVAL


b.

Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.

NOTICE:
·

When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.

·

Do not forcibly open the valve, as it may be damaged or deformed.

·

When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.

·

When cleaning the electric EGR control valve assembly, care should be taken to prevent the ingress of cleaning solvent into the bearings of the valve shaft, and when wiping off deposits on the EGR valve, care should be taken not to push the deposits into the bearings of valve shaft. These contaminants may adversely affect the function of the EGR valve.

·

When cleaning the electric EGR control valve assembly, perform the initialization procedure.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>INITIALIZATION



HINT:
·

If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.

·

If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power. In this case, clean the electric EGR control valve assembly.




c.

Reinstall the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>INSTALLATION


Result:
Proceed to
NEXT



NEXT

41.REPLACE NO. 1 EGR COOLER
41.REPLACE NO. 1 EGR COOLER

Result:
Proceed to
NEXT



NEXT

19.CHECK FOR BLACK SMOKE
42.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

19.CHECK FOR BLACK SMOKE