Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  P24AE12  Particulate Matter Sensor Circuit High Circuit Short to Battery  P24AE14  Particulate Matter Sensor Circuit Low Circuit Short to Ground or Open  P24AE1C  Particulate Matter Sensor Circuit Circuit Voltage Out of Range  P24AE96  Particulate Matter Sensor Circuit Range/Performance Component Internal Failure  P24B301  Particulate Matter Sensor Heater Control Circuit/Open General Electrical Failure  P24B31E  Particulate Matter Sensor Heater Resistance Circuit Resistance Out of Range  P24C601  Particulate Matter Sensor Temperature Circuit General Electrical Failure  P24C61C  Particulate Matter Sensor Temperature Circuit Range/Performance Circuit Voltage Out of Range  P24D000  Particulate Matter Sensor Supply Voltage Circuit Low  P24D100  Particulate Matter Sensor Regeneration Incomplete  P24DA00  Particulate Matter Sensor Exhaust Sample Error Bank 1  


DESCRIPTION

The particulate matter sensor is installed in the center exhaust pipe assembly to detect the PM value.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P24AE12 Particulate Matter Sensor Circuit High Circuit Short to Battery Open or short in particulate matter sensor circuit for 10 seconds or more
(2 trip detection logic)
Particulate matter sensor assembly Class B1 DTC stored SAE Code: P24B1
P24AE14 Particulate Matter Sensor Circuit Low Circuit Short to Ground or Open Open or short in particulate matter sensor circuit for 10 seconds or more
(2 trip detection logic)
Particulate matter sensor assembly Class B1 DTC stored SAE Code: P24B0
P24AE1C Particulate Matter Sensor Circuit Circuit Voltage Out of Range Particulate matter sensor voltage out of range for 3 seconds or more
(2 trip detection logic)
Particulate matter sensor assembly Class B1 DTC stored SAE Code: P24AE
P24AE96 Particulate Matter Sensor Circuit Range/Performance Component Internal Failure Particulate matter sensor out of range for 3 seconds or more
(2 trip detection logic)
Particulate matter sensor assembly Class B1 DTC stored SAE Code: P24AF
P24B301 Particulate Matter Sensor Heater Control Circuit/Open General Electrical Failure Malfunction in particulate matter sensor heater circuit for 10 seconds or more
(2 trip detection logic)
Particulate matter sensor assembly Class B1 DTC stored SAE Code: P24B3
P24B31E Particulate Matter Sensor Heater Resistance Circuit Resistance Out of Range Malfunction in particulate matter sensor heater resistance out of range for 3 seconds or more
(2 trip detection logic)
Particulate matter sensor assembly Class B1 DTC stored SAE Code: P24B7
P24C601 Particulate Matter Sensor Temperature Circuit General Electrical Failure Malfunction in particulate matter sensor temperature sensor for 10 seconds or more
(2 trip detection logic)
Particulate matter sensor assembly Class B1 DTC stored SAE Code: P24C6
P24C61C Particulate Matter Sensor Temperature Circuit Range/Performance Circuit Voltage Out of Range Either of the following conditions is met (2 trip detection logic):
·

When the power switch is turned on (IG) after the engine is fully warmed up and then stopped for at least 10 hours, the deviation between the particulate matter sensor temperature sensor and No. 4 exhaust temperature sensor meets or exceeds the threshold.

·

The particulate matter sensor temperature sensor value deviates from the estimated value for 15 seconds or more.


Particulate matter sensor assembly Class B1 DTC stored SAE Code: P24C7
P24D000 Particulate Matter Sensor Supply Voltage Circuit Low Low power supply to particulate matter sensor circuit for 10 seconds or more
(2 trip detection logic)
·

Particulate matter sensor assembly

·

NOx PM relay

·

Harness or connector


Class B1 DTC stored SAE Code: P24D0
P24D100 Particulate Matter Sensor Regeneration Incomplete Particulate matter sensor regeneration malfunction
(2 trip detection logic)
Particulate matter sensor assembly Class B1 DTC stored SAE Code: P24D1
P24DA00 Particulate Matter Sensor Exhaust Sample Error Bank 1 Particulate matter sensor exhaust sample error
(2 trip detection logic)
·

Particulate matter sensor assembly

·

Particulate matter sensor assembly installation malfunction


Class B1 DTC stored SAE Code: P24DA

Related Data List
DTC No. Data List
P24AE12
P24AE14
P24AE1C
P24AE96
P24B301
P24B31E
P24C601
P24C61C
P24D000
P24D100
P24DA00
·

PM Sensor Output Current

·

Status of PM Sensor IDE Circuit

·

Status of PM Sensor IDE (+ Side)

·

Status of PM Sensor Temperature

·

Status of PM Sensor IDE (- Side)

·

Status of PM Sensor Heater ON Malfunction

·

Status of PM Sensor Heater OFF Malfunction



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P24AE12
P24AE14
P24AE1C
P24AE96
P24B301
P24B31E
P24C61C
P24D000
Engine switch on (IG) and wait for 10 seconds or more
P24C601
P24D100
After the engine is warmed up, drive the vehicle at a low speed.
P24DA00 Allow the engine to soak for approximately 3 hours to cool the exhaust system.
After the exhaust system cools, repeatedly accelerate and decelerate the vehicle from 30 to 40 km/h (19 to 25 mph) and drive it for approximately 20 minutes.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

Result:
Result Proceed to
DTC P24D000 is output A
DTC P24C601 and P246E2A is output*2 B
DTC P24DA00 is output C
DTC P24AE12, P24AE14, P24AE1C, P24AE96, P24B301, P24B31E, P24C601, P24C61C and/or P24D100 is output D
DTC P24AE12 or P24AE14, P24AE1C, P24AE96, P24B301, P24B31E, P24C601, P24C61C, P24D000, P24D100 and/or P24DA00 and other DTCs are output*1 E


HINT:
·

*1: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.

·

*2: If P246E2A is also output as a pending DTC, diagnose P246E2A first.




A

2.INSPECT NOX PM RELAY

B

C

7.INSPECT PARTICULATE MATTER SENSOR ASSEMBLY

D

11.REPLACE PARTICULATE MATTER SENSOR ASSEMBLY

E

2.INSPECT NOX PM RELAY

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NOX PM RELAY - PARTICULATE MATTER SENSOR ASSEMBLY)

NG

6.REPLACE NOX PM RELAY
3.CHECK HARNESS AND CONNECTOR (NOX PM RELAY - PARTICULATE MATTER SENSOR ASSEMBLY)
a.

Disconnect the particulate matter sensor assembly connector.


b.

Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
1E-3 - Y4-1 (BATT) Always Below 1 Ω
1E-3 - Y4-1 (BATT) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

11.REPLACE PARTICULATE MATTER SENSOR ASSEMBLY

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

d.

Turn the engine switch off and wait for 30 seconds.


e.

Turn the engine switch on (IG) and wait for 10 second or more.


f.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

6.REPLACE NOX PM RELAY
a.

Replace the NOx PM relay.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.INSPECT PARTICULATE MATTER SENSOR ASSEMBLY
a.

Check the installation condition of the particulate matter sensor.

OK:

The particulate matter sensor detection part is correctly installed to the exhaust pipe.



Result:
Proceed to
OK
NG



OK

10.REPLACE PARTICULATE MATTER SENSOR ASSEMBLY

NG

8.REPAIR PARTICULATE MATTER SENSOR ASSEMBLY
8.REPAIR PARTICULATE MATTER SENSOR ASSEMBLY
a.

Install the particulate matter sensor in the correct condition.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>PARTICULATE MATTER SENSOR>INSTALLATION


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Allow the engine to soak for approximately 3 hours to cool the exhaust system.


b.

Connect the GTS to the DLC3.


c.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

d.

Turn the engine switch off for 30 seconds or more.


e.

After the exhaust system cools, repeatedly accelerate and decelerate the vehicle from 30 to 40 km/h (19 to 25 mph) and drive it for approximately 20 minutes.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and Transmission / Utility / All Readiness.

Powertrain > Engine and Transmission > Utility
Tester Display
All Readiness
50005 456 20

ii.

Input DTC P24DA00.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC DTC P24DA00 is output A
All Readiness ABNORMAL
NORMAL B


HINT:

If STATUS is INCOMPLETE, repeatedly accelerate and decelerate the vehicle from 30 to 40 km/h (19 to 25 mph) and drive it again.





A

10.REPLACE PARTICULATE MATTER SENSOR ASSEMBLY

B

END

10.REPLACE PARTICULATE MATTER SENSOR ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE PARTICULATE MATTER SENSOR ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED