Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  U029D87  Lost Communication with NOx Sensor "A" Missing Message  U029E87  Lost Communication with NOx Sensor "B" Missing Message  U02A387  Lost Communication with PM Sensor Missing Message  


DESCRIPTION

The ECM sends and receives data to and from the No. 1 nitrogen oxides sensor, No. 2 nitrogen oxides sensor and particulate matter sensor via local CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
U029D87 Lost Communication with NOx Sensor "A" Missing Message Communication stops between the ECM and the No. 1 nitrogen oxides sensor for 1 second or more.
(1 trip detection logic)
·

No. 1 nitrogen oxides sensor

·

Harness or connector

·

ECM


Class A DTC stored SAE Code: U029D
U029E87 Lost Communication with NOx Sensor "B" Missing Message Communication stops between the ECM and the No. 2 nitrogen oxides sensor for 1 second or more.
(1 trip detection logic)
·

No. 2 nitrogen oxides sensor

·

Harness or connector

·

ECM


Class B1 DTC stored SAE Code: U029E
U02A387 Lost Communication with PM Sensor Missing Message Communication stops between the ECM and the particulate matter sensor for 1.6 seconds or more.
(1 trip detection logic)
·

Particulate matter sensor

·

Harness or connector

·

ECM


Class B1 DTC stored SAE Code: U02A3

MONITOR DESCRIPTION

The ECM stores a DTC when a communication malfunction occurs between the No. 1 nitrogen oxides sensor, No. 2 nitrogen oxides sensor, particulate matter sensor and ECM.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
U029D87
U029E87
Engine switch on (IG) and wait for 1 second or more
U02A387 Engine switch on (IG) and wait for 1.6 seconds or more

WIRING DIAGRAM

A445681E02
3.74,1.01 4.354,1.208 0.615,0.198 10 false Y3 3.865,4.177 6.406,4.427 2.542,0.25 10 false No. 1 Nitrogen Oxides Sensor 3.906,4.01 4.594,4.281 0.688,0.271 10 false A24 3.552,1.146 6.094,1.396 2.542,0.25 10 false No. 2 Nitrogen Oxides Sensor 3.792,2.615 6.333,2.865 2.542,0.25 10 false Particulate Matter Sensor 4.24,2.115 4.854,2.313 0.615,0.198 10 false GND 4.229,0.729 4.844,0.927 0.615,0.198 10 false GND 4.24,0.313 4.854,0.51 0.615,0.198 10 false BATT 4.74,0.313 5.354,0.51 0.615,0.198 10 false CAN+ 4.74,0.646 5.354,0.844 0.615,0.198 10 false CAN- 4.698,1.771 5.313,1.969 0.615,0.198 10 false CAN+ 4.75,2.125 5.365,2.323 0.615,0.198 10 false CAN- 4.719,3.188 5.333,3.385 0.615,0.198 10 false CAN+ 4.74,3.615 5.354,3.813 0.615,0.198 10 false CAN- 2.302,6.302 3.688,6.49 1.385,0.188 10 false E/G W/PMP 4.229,1.771 4.844,1.969 0.615,0.198 10 false BATT 4.25,3.417 4.865,3.615 0.615,0.198 10 false GND 3.792,2.448 4.406,2.646 0.615,0.198 10 false Y4 4.083,2.021 4.24,2.219 0.156,0.198 10 false 4 4.063,1.635 4.219,1.833 0.156,0.198 10 false 1 5.156,1.604 5.313,1.802 0.156,0.198 10 false 2 5.177,3.417 5.333,3.615 0.156,0.198 10 false 3 5.177,1.948 5.333,2.146 0.156,0.198 10 false 3 5.167,3.021 5.323,3.219 0.156,0.198 10 false 2 4.073,3.333 4.229,3.531 0.156,0.198 10 false 4 4.073,3.042 4.229,3.24 0.156,0.198 10 false 5 4.063,0.625 4.219,0.823 0.156,0.198 10 false 4 4.063,0.198 4.219,0.396 0.156,0.198 10 false 5 5.177,0.177 5.333,0.375 0.156,0.198 10 false 2 5.177,0.51 5.333,0.708 0.156,0.198 10 false 3 1.625,4.542 3.313,4.771 1.688,0.229 10 false NOX 3.5,4.198 3.656,4.396 0.156,0.198 10 false 3 3.229,4.188 3.719,4.427 0.49,0.24 10 false 1E 5.729,3.021 5.99,3.229 0.26,0.208 10 false 27 5.729,3.458 5.99,3.667 0.26,0.208 10 false 35 5.969,3.615 6.583,3.813 0.615,0.198 10 false CAND 5.969,3.177 6.583,3.375 0.615,0.198 10 false CANU 5.958,7.552 6.573,7.75 0.615,0.198 10 false MREL 6.229,8.25 6.844,8.448 0.615,0.198 10 false N2 6.229,8.427 6.844,8.625 0.615,0.198 10 false ECM 5.708,7.396 5.969,7.604 0.26,0.208 10 false 14 3.583,7.281 4.969,7.469 1.385,0.188 10 false EFI NO. 3 2.469,7.885 3.854,8.073 1.385,0.188 10 false EFI-MAIN 0.948,5.531 1.26,5.729 0.313,0.198 10 false A 0.958,5.833 1.115,6.031 0.156,0.198 10 false 4 1.74,6.625 4.583,6.875 2.844,0.25 10 false No. 1 Integration Relay 3.052,8.26 5.115,8.448 2.063,0.188 10 false : CAN Communication Line 0.385,7.521 1,7.719 0.615,0.198 10 false FL MAIN 0.948,5.365 1.125,5.563 0.177,0.198 10 false 1 3.5,5.844 3.677,6.042 0.177,0.198 10 false 8 0.625,8.115 1.24,8.313 0.615,0.198 10 false Battery 4.24,3.156 4.854,3.354 0.615,0.198 10 false BATT 0.896,6.021 1.208,6.219 0.313,0.198 10 false 1E 3.031,5.688 4.417,5.875 1.385,0.188 10 false EFI NO. 2 2.531,5.167 4.219,5.396 1.688,0.229 10 false NOX 0.792,7.26 2.177,7.448 1.385,0.188 10 false EFI-MAIN 1.688,5.677 2.302,6.01 0.615,0.333 10 false E/G W/PMP 3.448,6.021 3.938,6.26 0.49,0.24 10 false 1E 3.646,6.979 3.823,7.177 0.177,0.198 10 false 1 4.01,6.969 4.188,7.167 0.177,0.198 10 false 2 0.844,6.979 1.021,7.177 0.177,0.198 10 false 1 1.24,6.979 1.417,7.177 0.177,0.198 10 false 2 1.552,4.271 1.729,4.469 0.177,0.198 10 false 1 1.917,4.271 2.094,4.469 0.177,0.198 10 false 2 4.24,3.667 4.854,3.865 0.615,0.198 10 false ADSW 4.073,3.563 4.229,3.76 0.156,0.198 10 false 1 3.104,7.031 3.281,7.229 0.177,0.198 10 false 5 2.333,7.031 2.51,7.229 0.177,0.198 10 false 3 3.104,7.646 3.281,7.844 0.177,0.198 10 false 2 2.323,7.656 2.5,7.854 0.177,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After the engine switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

According to the display on the GTS, select "Health Check".


d.

Check for currently output system DTCs.

Result:
Result Proceed to
DTC U02A387 is output A
DTC U029D87 is output B
DTC U029E87 is output C
2 or more of the following DTCs are simultaneously output: U02A387, U029D87 or U029E87 D




A

2.CHECK PARTICULATE MATTER SENSOR

B

3.CHECK NO. 1 NITROGEN OXIDES SENSOR

C

4.CHECK NO. 2 NITROGEN OXIDES SENSOR

D

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SENSOR)
2.CHECK PARTICULATE MATTER SENSOR
a.

Disconnect the particulate matter sensor connector.


b.

Turn the engine switch on (IG).


c.
A426728C05
1.469,0.198 1.948,0.531 0.479,0.333 1.125,1.771 1.365,1.271 true 2.573,1.833 2.177,1.271 true 1.573,1.813 1.677,1.302 true 2.104,1.833 1.906,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.625,0.292 1.938,0.49 0.313,0.198 10 false Y4 2.573,1.833 3.031,2.031 0.458,0.198 10 false GND 0.771,1.833 1.313,2.031 0.542,0.198 10 false BATT 1.417,1.833 1.958,2.031 0.542,0.198 10 false CAN+ 1.99,1.833 2.531,2.031 0.542,0.198 10 false CAN-
*a Front view of wire harness connector
(to Particulate Matter Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Y4-1 (BATT) - Y4-4 (GND) Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y4-2 (CAN+) - Y4-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
Y4-2 (CAN+) or Y4-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Y4-2 (CAN+) or Y4-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
Y4-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK NO. 1 NITROGEN OXIDES SENSOR
a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Turn the engine switch on (IG).


c.
A383897C23
1.469,0.198 1.948,0.531 0.479,0.333 1.25,1.792 1.448,1.271 true 2.479,1.76 2.219,1.271 true 2.167,1.771 1.948,1.281 true 1.573,1.76 1.719,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.552,0.292 2.125,0.51 0.573,0.219 10 false A24 2.083,1.781 2.542,1.979 0.458,0.198 10 false GND 2.458,1.781 3,1.979 0.542,0.198 10 false BATT 1.313,1.792 1.854,1.99 0.542,0.198 10 false CAN- 0.896,1.781 1.438,1.979 0.542,0.198 10 false CAN+
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-5 (BATT) - A24-4 (GND) Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-2 (CAN+) - A24-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A24-2 (CAN+) or A24-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A24-2 (CAN+) or A24-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A24-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK NO. 2 NITROGEN OXIDES SENSOR
a.

Disconnect the No. 2 nitrogen oxides sensor connector.


b.

Turn the engine switch on (IG).


c.
A383897C24
1.469,0.198 1.948,0.531 0.479,0.333 1.25,1.792 1.448,1.271 true 2.479,1.76 2.219,1.271 true 2.167,1.771 1.948,1.281 true 1.573,1.76 1.719,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.646,0.292 2.219,0.51 0.573,0.219 10 false Y3 2.083,1.781 2.542,1.979 0.458,0.198 10 false GND 2.458,1.781 3,1.979 0.542,0.198 10 false BATT 1.313,1.792 1.854,1.99 0.542,0.198 10 false CAN- 0.896,1.781 1.438,1.979 0.542,0.198 10 false CAN+
*a Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Y3-5 (BATT) - Y3-4 (GND) Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y3-2 (CAN+) - Y3-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
Y3-2 (CAN+) or Y3-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Y3-2 (CAN+) or Y3-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
Y3-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SENSOR)
A449209C03
1.448,0.104 1.948,0.385 0.5,0.281 2.219,0.104 2.719,0.385 0.5,0.281 4.813,0.104 5.313,0.385 0.5,0.281 1.781,1.448 2.198,1.031 true 4.333,1.458 4.75,1.042 true 2.719,1.458 2.458,1.052 true 5.656,1.448 5.396,1.042 true 1.542,0.167 2.073,0.49 0.531,0.323 10 false A24 2.406,0.156 2.833,0.458 0.427,0.302 10 false Y3 4.979,0.156 5.313,0.479 0.333,0.323 10 false Y4 1.99,0.156 2.323,0.479 0.333,0.323 10 false *a 5.354,0.156 5.688,0.479 0.333,0.323 10 false *c 2.771,0.177 3.104,0.5 0.333,0.323 10 false *b 2.635,1.5 3.125,1.729 0.49,0.229 10 false BATT 4.135,1.5 4.625,1.688 0.49,0.188 10 false BATT 1.542,1.5 1.99,1.698 0.448,0.198 10 false GND 5.604,1.5 6.094,1.74 0.49,0.24 10 false GND
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)
*b Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)
*c Front view of wire harness connector
(to Particulate Matter Sensor)
- -


a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Disconnect the No. 2 nitrogen oxides sensor connector.


c.

Disconnect the particulate matter sensor connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-5 (BATT) - A24-4 (GND) Engine switch on (IG) 11 to 14 V
Y3-5 (BATT) - Y3-4 (GND) Engine switch on (IG) 11 to 14 V
Y4-1 (BATT) - Y4-4 (GND) Engine switch on (IG) 11 to 14 V



e.

Reconnect the particulate matter sensor connector.


f.

Reconnect the No. 2 nitrogen oxides sensor connector.


g.

Reconnect the No. 1 nitrogen oxides sensor connector.


Result:
Proceed to
OK
NG



OK

6.CHECK ECM

NG

10.CHECK HARNESS AND CONNECTOR (SENSOR CONNECTOR - BODY GROUND)
6.CHECK ECM
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.
A449464C02
1.719,0.396 2.25,0.729 0.531,0.333 1.125,2.344 1.667,2.094 true 1.365,2.688 1.656,2.177 true 1.854,0.479 2.313,0.677 0.458,0.198 10 false N2 0.156,0.125 0.615,0.323 0.458,0.198 10 false *a 0.417,2.333 1.26,2.563 0.844,0.229 10 false 27 (CANU) 0.708,2.698 1.552,2.927 0.844,0.229 10 false 35 (CAND)
*a Rear view of wire harness connector
(to ECM Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-27 (CANU) - N2-35 (CAND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
N2-27 (CANU) or N2-35 (CAND) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N2-27 (CANU) or N2-35 (CAND) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

7.CHECK PARTICULATE MATTER SENSOR
7.CHECK PARTICULATE MATTER SENSOR
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Disconnect the particulate matter sensor connector.


d.
A449464C02
1.719,0.396 2.25,0.729 0.531,0.333 1.125,2.344 1.667,2.094 true 1.365,2.688 1.656,2.177 true 1.854,0.479 2.313,0.677 0.458,0.198 10 false N2 0.156,0.125 0.615,0.323 0.458,0.198 10 false *a 0.417,2.333 1.26,2.563 0.844,0.229 10 false 27 (CANU) 0.708,2.698 1.552,2.927 0.844,0.229 10 false 35 (CAND)
*a Rear view of wire harness connector
(to ECM Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-27 (CANU) - N2-35 (CAND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
N2-27 (CANU) or N2-35 (CAND) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N2-27 (CANU) or N2-35 (CAND) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



NG

OK

8.CHECK NO. 1 NITROGEN OXIDES SENSOR
8.CHECK NO. 1 NITROGEN OXIDES SENSOR
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Disconnect the No. 1 nitorogen oxides sensor connector.


d.
A449464C02
1.719,0.396 2.25,0.729 0.531,0.333 1.125,2.344 1.667,2.094 true 1.365,2.688 1.656,2.177 true 1.854,0.479 2.313,0.677 0.458,0.198 10 false N2 0.156,0.125 0.615,0.323 0.458,0.198 10 false *a 0.417,2.333 1.26,2.563 0.844,0.229 10 false 27 (CANU) 0.708,2.698 1.552,2.927 0.844,0.229 10 false 35 (CAND)
*a Rear view of wire harness connector
(to ECM Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-27 (CANU) - N2-35 (CAND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
N2-27 (CANU) or N2-35 (CAND) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N2-27 (CANU) or N2-35 (CAND) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



NG

OK

9.CHECK NO. 2 NITROGEN OXIDES SENSOR
9.CHECK NO. 2 NITROGEN OXIDES SENSOR
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Disconnect the No. 2 nitorogen oxides sensor connector.


d.
A449464C02
1.719,0.396 2.25,0.729 0.531,0.333 1.125,2.344 1.667,2.094 true 1.365,2.688 1.656,2.177 true 1.854,0.479 2.313,0.677 0.458,0.198 10 false N2 0.156,0.125 0.615,0.323 0.458,0.198 10 false *a 0.417,2.333 1.26,2.563 0.844,0.229 10 false 27 (CANU) 0.708,2.698 1.552,2.927 0.844,0.229 10 false 35 (CAND)
*a Rear view of wire harness connector
(to ECM Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-27 (CANU) - N2-35 (CAND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
N2-27 (CANU) or N2-35 (CAND) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N2-27 (CANU) or N2-35 (CAND) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



NG

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (SENSOR CONNECTOR - BODY GROUND)
A449209C03
1.448,0.104 1.948,0.385 0.5,0.281 2.219,0.104 2.719,0.385 0.5,0.281 4.813,0.104 5.313,0.385 0.5,0.281 1.781,1.448 2.198,1.031 true 4.333,1.458 4.75,1.042 true 2.719,1.458 2.458,1.052 true 5.656,1.448 5.396,1.042 true 1.542,0.167 2.073,0.49 0.531,0.323 10 false A24 2.406,0.156 2.833,0.458 0.427,0.302 10 false Y3 4.979,0.156 5.313,0.479 0.333,0.323 10 false Y4 1.99,0.156 2.323,0.479 0.333,0.323 10 false *a 5.354,0.156 5.688,0.479 0.333,0.323 10 false *c 2.771,0.177 3.104,0.5 0.333,0.323 10 false *b 2.635,1.5 3.125,1.729 0.49,0.229 10 false BATT 4.135,1.5 4.625,1.688 0.49,0.188 10 false BATT 1.542,1.5 1.99,1.698 0.448,0.198 10 false GND 5.604,1.5 6.094,1.74 0.49,0.24 10 false GND
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)
*b Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)
*c Front view of wire harness connector
(to Particulate Matter Sensor)
- -


a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Disconnect the No. 2 nitrogen oxides sensor connector.


c.

Disconnect the particulate matter sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-4 (GND) - Body ground Always Below 1 Ω
Y3-4 (GND) - Body ground Always Below 1 Ω
Y4-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - NO. 1 NITROGEN OXIDES SENSOR, NO. 2 NITROGEN OXIDES SENSOR, PARTICULATE MATTER SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - NO. 1 NITROGEN OXIDES SENSOR, NO. 2 NITROGEN OXIDES SENSOR, PARTICULATE MATTER SENSOR)
a.

Remove the No. 1 integration relay from the No. 1 engine room relay block and junction blockassembly.


b.

Disconnect the No. 1 nitorogen oxides sensor connector.


c.

Disconnect the No. 2 nitorogen oxides sensor connector.


d.

Disconnect the particulate matter sensor connector.


e.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
1E-3 - A24-5 (BATT) Always Below 1 Ω
1E-3 - Y3-5 (BATT) Always Below 1 Ω
1E-3 - Y4-1 (BATT) Always Below 1 Ω
1E-3 - A24-5 (BATT) - Body ground and other terminals Always 10 kΩ or higher
1E-3 - Y3-5 (BATT) - Body ground and other terminals Always 10 kΩ or higher
1E-3 - Y4-1 (BATT) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

12.INSPECT NO. 1 INTEGRATION RELAY (NOX RELAY AND E/G W/PMP RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT NO. 1 INTEGRATION RELAY (NOX RELAY AND E/G W/PMP RELAY)
a.

Inspect the No. 1 integration relay (NOX relay).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION


b.

Inspect the No. 1 integration relay (E/G W/PMP relay).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

13.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)

NG

REPLACE NO. 1 INTEGRATION RELAY

13.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)
A443534C01
0.573,2.698 0.875,2.927 0.302,0.229 0.677,2.729 0.833,2.927 0.156,0.198 10 false A 0.073,0.042 0.385,0.24 0.313,0.198 10 false *a
*a No. 1 Engine Room Relay Block and Junction Block Assembly without No. 1 Integration Relay


a.

Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)

14.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-4 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - EFI MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - EFI MAIN RELAY)
a.

Remove the EFI MAIN relay from the No. 1 engine room relay block and junction block assembly.


b.

Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-8 - EFI MAIN relay terminal 5 Always Below 1 Ω
1E-8 or EFI MAIN relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR