Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › EGR COOLER › 2020.05–2021.07
RM35X0E _51 Engine / Hybrid System _079220 1GD-FTV EMISSION CONTROL _0384172 EGR COOLER A

1GD-FTV EMISSION CONTROL  EGR COOLER  INSTALLATION  


PROCEDURE

Hide 25681 1.INSTALL NO. 1 EGR COOLER

a.

Install a new gasket and the No. 1 EGR cooler to the No. 2 EGR valve assembly with electric EGR control valve assembly with the 4 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 2.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.
A442617C02
0.135,0.156 0.448,0.313 0.313,0.156 10 true *A 0.198,2.531 0.51,2.688 0.313,0.156 10 true *B 0.771,0.396 0.948,0.552 0.177,0.156 10 true 4 3.073,1.729 3.25,1.885 0.177,0.156 10 true 3 1.906,2.021 2.083,2.177 0.177,0.156 10 true 2 1.406,2.021 1.583,2.177 0.177,0.156 10 true 1 0.771,2.802 0.948,2.958 0.177,0.156 10 true 4 3.094,4.146 3.271,4.302 0.177,0.156 10 true 3 1.99,4.427 2.167,4.583 0.177,0.156 10 true 2 1.406,4.438 1.583,4.594 0.177,0.156 10 true 1
*A for Single Actuator EGR Valve Assembly
*B for Double Actuator EGR Valve Assembly


for Air Cooled Type Intercooler:

i.

Temporarily install the No. 1 EGR cooler and No. 2 EGR valve assembly with electric EGR control valve assembly to the intake manifold with the 4 bolts.


ii.

Tighten the 4 bolts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)



b.
A452853C01
1.135,0.844 1.354,0.469 1.354,0.469 1.552,0.469 true 1.094,1.958 1.229,2.125 0.135,0.167 10 true 1 2.427,1.844 2.563,2.01 0.135,0.167 10 true 2 2.948,0.938 3.083,1.104 0.135,0.167 10 true 3 0.563,0.823 0.698,0.99 0.135,0.167 10 true 4 1.604,0.365 1.854,0.542 0.25,0.177 10 true *1
*1 No. 2 Intercooler Support Bracket


for Water Cooled Type Intercooler:

i.

Temporarily install the No. 1 EGR cooler and No. 2 EGR valve assembly with electric EGR control valve assembly and No. 2 intercooler support bracket to the intake manifold with the 4 bolts.


ii.

Tighten the 4 bolts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)



Hide 25601 3.CONNECT EGR PIPE WITH COOLER SUB-ASSEMBLY (for Double Actuator EGR Bypass Valve)

Hide 25601 4.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (for Single Actuator EGR Bypass Valve)

Hide 16209 5.CONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16206B 6.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install the No. 3 water by-pass pipe sub-assembly to the No. 1 EGR cooler with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 9 water by-pass hose to the electric EGR control valve assembly, and slide the clamp to secure the hose.


c.

Connect the No. 8 water by-pass hose to the No. 3 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.


d.

Attach the clamp and connect the No. 4 fuel hose to the No. 3 water by-pass pipe sub-assembly.


Hide 89425D 8.INSTALL NO. 5 EXHAUST GAS TEMPERATURE SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)

Hide 12632 13.INSTALL NO. 2 ENGINE COVER BRACKET (for Air Cooled Type Intercooler)

Hide 89421C 15.INSTALL DIESEL TURBO PRESSURE SENSOR

Hide 16278 16.INSTALL NO. 2 WATER BY-PASS PIPE (for Air Cooled Type Intercooler)

Hide 87209 17.INSTALL WATER HOSE SUB-ASSEMBLY (w/ Heater)

Hide 26100G 18.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 17940D 19.INSTALL INTERCOOLER ASSEMBLY (for Water Cooled Type Intercooler)

Hide 55701J 20.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 85110 21.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

Hide 22.ADD ENGINE COOLANT (for Air Cooled Type Intercooler)

Hide 23.INSPECT FOR COOLANT LEAK (for Air Cooled Type Intercooler)