Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL SUPPLY PUMP › 2020.05–2021.07
RM35X0E _51 Engine / Hybrid System _079306 1GD-FTV FUEL _0385713 FUEL SUPPLY PUMP A

1GD-FTV FUEL  FUEL SUPPLY PUMP  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 22100 1.INSTALL SUPPLY PUMP ASSEMBLY

NOTICE:
·
A347308C03
0.115,0.104 0.51,0.385 0.396,0.281 12 false *A 0.115,2.542 0.458,2.833 0.344,0.292 12 false *B
*A w/ Pressurized Fuel Filter
*B w/o Pressurized Fuel Filter


Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.

·

With SST set, do not turn the crankshaft more than a half rotation.



a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the supply pump assembly.


c.
A347065C01
0.958,1.594 1.146,1.594 1.146,1.594 1.427,1.208 true 0.75,1.51 1.063,1.667 0.313,0.156 10 true *a
*a Groove


To insert the supply pump assembly shaft in the supply pump shaft sprocket, it may be necessary to turn the supply pump assembly several degrees and the groove in the supply pump assembly shaft are aligned.

HINT:
A343559C02
2.125,3.302 2.292,2.646 2.292,2.646 2.51,2.646 false 2.521,2.521 2.833,2.677 0.313,0.156 10 false *a 1.208,2.198 1.521,2.354 0.313,0.156 10 false *b 3.063,3.406 3.375,3.563 0.313,0.156 10 false 6°
*a Supply Pump Shaft Key
*b Upper Side


When installing a new supply pump assembly, adjust the supply pump assembly injection pump drive shaft key assignment by turning the supply pump assembly shown in the illustration.



d.
A347066C01
1.635,1.74 2.208,1.74 false 1.156,2.125 1.885,2.125 1.885,2.125 1.885,1.74 false 2.438,0.792 2.583,0.969 2.583,0.969 2.823,0.969 true 0.802,1.979 1.115,2.135 0.313,0.156 10 false *a 2.24,1.635 2.719,1.823 0.479,0.188 10 true SST 2.854,0.875 3.333,1.063 0.479,0.188 10 true SST
*a Hold
V113147

Turn


Using SST, tighten clockwise direction the supply pump assembly, and then temporarily install the 3 fuel supply pump fixing nuts.

SST
09213-58014  (91551-80840)
09330-00021  
09241-11010  


e.
A344940E01
1.365,1.75 1.365,1.49 1.365,1.49 1.656,1.052 true 1.292,1.74 1.521,1.938 0.229,0.198 10 true A

Using SST, tighten and insert the supply pump assembly up to the position shown in the illustration and tighten the 3 fuel supply pump fixing nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

After tightening the part with SST, a gap of 2 to 3 mm in area A shown in the illustration is normal.



f.

Install the No. 1 fuel pump bracket with the 2 bolts to the supply pump assembly and cylinder block sub-assembly.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


g.
A344938E01
1.219,1.552 1.417,1.552 1.417,1.552 1.771,1.313 true 0.865,1.458 1.323,1.656 0.458,0.198 10 true SST

Remove SST and the 3 set bolts.


h.
A347061C01
0.948,2.052 1.573,2.052 1.573,2.052 1.573,1.885 false 1.281,1.885 1.844,1.885 false 0.5,1.958 0.813,2.115 0.313,0.156 10 false *a 1.875,1.802 2.333,2 0.458,0.198 10 true SST
*a Hold
V113147

Turn


Using SST, hold the crankshaft pulley sub-assembly and tighten the supply pump shaft nut.

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)


Hide 11324 2.INSTALL TIMING CHAIN COVER PLATE

a.

Install the timing chain cover plate and new gasket with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Do not install the timing chain cover plate with the bolts included with SST.



Hide 23243B 3.INSTALL FUEL PUMP MOTOR WIRE

a.

Attach the clamp and install the fuel pump motor wire.


b.

Connect the fuel pump motor wire connector.


Hide 22803 4.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY

a.

Install the fuel injection pump cover sub-assembly to the supply pump assembly.


Hide 5.INSTALL NO. 4 FUEL PIPE (w/ Pressurized Fuel Filter without DPF)

a.
A370020E01
0.271,2.292 0.479,2.469 0.208,0.177 10 true 1 1.781,2.958 1.99,3.135 0.208,0.177 10 true 2

Tighten the No. 4 fuel pipe with the 2 union bolts and bolts with 2 new gaskets in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 23271H 6.INSTALL NO. 1 FUEL HOSE

a.

Install the No. 1 fuel hose to the supply pump assembly and No. 2 fuel pipe, and slide the 2 clips to secure the hoses.


Hide 23273H 7.INSTALL NO. 2 FUEL HOSE

a.

Install the No. 2 fuel hose to the supply pump assembly and No. 3 nozzle leakage pipe assembly, and slide the 2 clips to secure the hoses.


Hide 16620 8.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 10.CONNECT INTERCOOLER COOLING WATER PIPE ASSEMBLY (for Water Cooled Type Intercooler)

Hide 88359 11.INSTALL VISCOUS HEATER V BELT (w/ Viscous Heater)

Hide 161B0 12.INSTALL ELECTRIC WATER PUMP ASSEMBLY (for Water Cooled Type Intercooler)

Hide 16551C 13.INSTALL NO. 1 INTERCOOLER COOLING WATER HOSE (for Water Cooled Type Intercooler)

Hide 16552C 14.INSTALL NO. 2 INTERCOOLER COOLING WATER HOSE (for Water Cooled Type Intercooler)

Hide 16571C 15.INSTALL NO. 1 RADIATOR HOSE

Hide 16470 16.INSTALL RADIATOR RESERVE TANK ASSEMBLY

Hide 16640 17.INSTALL INTERCOOLER RESERVE TANK ASSEMBLY (for Water Cooled Type Intercooler)

Hide 44360 18.CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 17303T 19.INSTALL AIR PIPE SUB-ASSEMBLY (for Air Cooled Type Intercooler)

Hide 25761B 20.CONNECT NO. 1 VACUUM TRANSMITTING HOSE (for Air Cooled Type Intercooler)

Hide 17030 21.INSTALL AIR HOSE ASSEMBLY (for Air Cooled Type Intercooler)

Hide 17751 22.INSTALL NO. 1 AIR CLEANER INLET

Hide 53106B 23.INSTALL RADIATOR COVER SUB-ASSEMBLY

Hide 51405A 24.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 52618 25.INSTALL LOWER FRONT BUMPER ABSORBER

Hide 51406A 26.INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)

Hide 28.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 29. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART