Home › Engine / Hybrid System › 1GD-FTV (LUBRICATION) › OIL PUMP › 2020.05–2021.07
RM35X0E _51 Engine / Hybrid System _079221 1GD-FTV LUBRICATION _0386560 OIL PUMP A

1GD-FTV LUBRICATION  OIL PUMP  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 11310 1.INSTALL TIMING CHAIN CASE ASSEMBLY AND ENGINE WATER PUMP ASSEMBLY

a.

Install a new gasket to the timing chain case assembly.


b.

Install the 4 new O-rings to the cylinder block sub-assembly and cylinder head sub-assembly.


c.

Clean and degrease the contact surfaces of the timing chain case assembly, cylinder head sub-assembly and cylinder block sub-assembly.


d.

Apply a coating of seal packing to the timing chain case assembly at the points shown in the illustration.

A339594C04
4.375,6.74 4.708,6.74 true 1.135,7.313 1.469,7.313 true 2.927,7.313 3.26,7.313 true 6.635,6.74 6.865,6.74 true 1.396,0.729 1.625,0.948 0.229,0.219 10 false *a 5.802,0.76 6.031,0.948 0.229,0.188 10 false *b 2.531,5.625 2.771,5.844 0.24,0.219 10 false E 6.917,6.646 7.135,6.833 0.219,0.188 10 false *d 6.917,6.188 7.146,6.385 0.229,0.198 10 false *c 4.781,6.635 4.979,6.823 0.198,0.188 10 false *f 1.531,6.906 1.729,7.083 0.198,0.177 10 false *e 1.552,7.219 1.781,7.427 0.229,0.208 10 false *f 5.521,4.958 5.698,5.146 0.177,0.188 10 true C 4.49,0.792 4.698,0.969 0.208,0.177 10 true B 5.104,0.781 5.292,0.958 0.188,0.177 10 true B 2.333,0.865 2.531,1.042 0.198,0.177 10 true A 4.938,4.969 5.104,5.135 0.167,0.167 10 true C 3.448,1.531 3.625,1.708 0.177,0.177 10 true D 2.49,2.052 2.677,2.229 0.188,0.177 10 true E 3.26,2.063 3.448,2.24 0.188,0.177 10 true E 3.969,1.385 4.177,1.552 0.208,0.167 10 true E 4.896,1.229 5.083,1.396 0.188,0.167 10 true E 6.208,5.958 6.906,6.188 0.698,0.229 10 true A-A, B-B 2.823,0.75 3.021,0.927 0.198,0.177 10 true A 4.25,5.938 4.635,6.156 0.385,0.219 10 true C-C 0.708,5.615 0.896,5.823 0.188,0.208 10 false D 4.802,6.198 5.01,6.385 0.208,0.188 10 false *c 3.344,6.917 3.573,7.135 0.229,0.219 10 false *c 3.344,7.219 3.563,7.417 0.219,0.198 10 false *f 5.01,0.115 5.219,0.302 0.208,0.188 10 false *c 2.198,0.094 2.531,0.333 0.333,0.24 10 false *g 2.063,5.25 2.344,5.458 0.281,0.208 10 false *h 5.5,5.333 5.781,5.542 0.281,0.208 11 false *i
*a 46 mm (1.81 in.) *b 50 mm (1.97 in.)
*c 2.0 to 3.0 mm (0.0787 to 0.118 in.) *d 2.5 to 3.5 mm (0.0984 to 0.138 in.)
*e 3.0 to 4.0 mm (0.118 to 0.158 in.) *f 1.5 to 2.5 mm (0.0591 to 0.0984 in.)
*g 13 to 15 mm (0.512 to 0.591 in.) *h 9.0 to 11 mm (0.354 to 0.433 in.)
*i 31 to 33 mm (1.22 to 1.30 in.) - -


Seal packing:
for line area D:

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent.

for line area A-A, B-B, C-C and E:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.


Seal Packing Application Specification:
Line Type and Area Seal Packing Diameter Application Area Seal Packing Application Length
Dashed Line 1.5 to 2.5 mm (0.0591 to 0.0984 in.) 2.0 to 3.0 mm (0.0787 to 0.118 in.) -
A - A 2.5 to 3.5 mm (0.0984 to 0.138 in.) 2.0 to 3.0 mm (0.0787 to 0.118 in.) 46 mm (1.81 in.)
B - B 2.5 to 3.5 mm (0.0984 to 0.138 in.) 2.0 to 3.0 mm (0.0787 to 0.118 in.) 50 mm (1.97 in.)
D 1.5 to 2.5 mm (0.0591 to 0.0984 in.) 3.0 to 4.0 mm (0.118 to 0.158 in.) -


NOTICE:
·

Using non-residue solvent, clean and remove any oil from the installation surface.

·

Install the part within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine within 2 hours after installation.




e.

Temporarily install the timing chain case assembly with the 15 bolts.

A339608C01
0.125,0.063 0.354,0.26 0.229,0.198 10 false *a 3.625,0.052 3.854,0.229 0.229,0.177 10 false *b 0.938,0.25 1.135,0.406 0.198,0.156 10 true A 1.031,0.542 1.219,0.698 0.188,0.156 10 true A 0.979,0.75 1.167,0.906 0.188,0.156 10 true D 0.875,0.99 1.063,1.146 0.188,0.156 10 true B 0.813,1.323 1,1.479 0.188,0.156 10 true B 0.646,1.729 0.833,1.885 0.188,0.156 10 true B 0.615,2.104 0.802,2.26 0.188,0.156 10 true B 0.646,2.51 0.833,2.667 0.188,0.156 10 true B 2.792,2.479 2.979,2.635 0.188,0.156 10 true B 2.885,2.073 3.073,2.229 0.188,0.156 10 true B 1.594,2.042 1.781,2.198 0.188,0.156 10 true B 1.792,1.927 1.948,2.083 0.156,0.156 10 true C 2.406,1.281 2.594,1.438 0.188,0.156 10 true C 2.177,2.042 2.365,2.198 0.188,0.156 10 true A 1.99,1.917 2.146,2.073 0.156,0.156 10 true C 1.771,1.177 1.958,1.333 0.188,0.156 10 true D 1.594,0.781 1.781,0.938 0.188,0.156 10 true C 2.573,1.031 2.76,1.188 0.188,0.156 10 true A 1.667,0.188 1.865,0.344 0.198,0.156 10 true A 1.969,0.188 2.167,0.344 0.198,0.156 10 true A 2.625,0.219 2.823,0.375 0.198,0.156 10 true A 2.656,0.479 2.854,0.635 0.198,0.156 10 true A 2.542,0.802 2.729,0.958 0.188,0.156 10 true D 5.948,1.271 6.104,1.427 0.156,0.156 10 true 1 4.26,1.75 4.417,1.896 0.156,0.146 10 true 2 4.406,1.302 4.552,1.448 0.146,0.146 10 true 3 4.469,0.99 4.625,1.135 0.156,0.146 10 true 4 5.135,0.792 5.281,0.948 0.146,0.156 10 true 5 5.531,1.917 5.677,2.073 0.146,0.156 10 true 6 5.354,1.917 5.51,2.073 0.156,0.156 10 true 7 5.167,2.042 5.313,2.198 0.146,0.156 10 true 8 4.25,2.51 4.406,2.656 0.156,0.146 10 true 9 4.156,2.104 4.354,2.26 0.198,0.156 10 true 10 5.688,2.052 5.885,2.219 0.198,0.167 10 true 11 6.427,2.094 6.635,2.26 0.208,0.167 10 true 12 6.323,2.479 6.531,2.646 0.208,0.167 10 true 13 6.125,1.052 6.323,1.208 0.198,0.156 10 true 14 6.083,0.833 6.271,0.99 0.188,0.156 10 true 15 5.323,1.177 5.521,1.333 0.198,0.156 10 true 16 4.531,0.75 4.719,0.896 0.188,0.146 10 true 17 4.51,0.271 4.708,0.417 0.198,0.146 10 true 18 4.594,0.563 4.792,0.708 0.198,0.146 10 true 19 5.208,0.198 5.406,0.344 0.198,0.146 10 true 20 5.521,0.198 5.708,0.344 0.188,0.146 10 true 21 6.208,0.49 6.406,0.635 0.198,0.146 10 true 22 6.208,0.208 6.406,0.365 0.198,0.156 10 true 23
*a Type of bolt *b Tightening


Bolt Length:
Item Length Thread Diameter
Bolt A 30 mm (1.18 in.) 8.0 mm (0.315 in.)
Bolt B 45 mm (1.77 in.) 8.0 mm (0.315 in.)
Bolt C 65 mm (2.56 in.) 8.0 mm (0.315 in.)
Bolt D 30 mm (1.18 in.) 10 mm (0.394 in.)



f.

Temporarily install a new gasket and the engine water pump assembly with the 8 bolts.


g.

Tighten the 23 bolts in the order shown in the illustration.

Torque:
for bolt A, B and C : 29 N*m (296 kgf*cm, 21 ft.*lbf)
for bolt D : 43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:

Check the torque of bolt 1 after tightening bolt 23.



Hide 22815A 2.INSTALL INJECTION PUMP INSULATOR

Hide 22100 3.INSTALL SUPPLY PUMP ASSEMBLY

Hide 13559 4.INSTALL NO. 1 CHAIN TENSIONER SLIPPER

Hide 13561 5.TEMPORARILY INSTALL NO. 1 CHAIN VIBRATION DAMPER

Hide 13506 6.INSTALL CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY

Hide 13561 7.TIGHTEN NO. 1 CHAIN VIBRATION DAMPER

Hide 13540 8.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13523 10.INSTALL CAMSHAFT TIMING SPROCKET

Hide 13562 11.INSTALL NO. 2 CHAIN VIBRATION DAMPER

Hide 13507 12.INSTALL NO. 2 CHAIN SUB-ASSEMBLY

Hide 13559 13.INSTALL NO. 2 CHAIN TENSIONER SLIPPER

Hide 13550 14.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 16.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 17.INSTALL BALANCESHAFT TIMING SPROCKET, BALANCESHAFT GEAR SUB-ASSEMBLY WITH NO. 3 CHAIN SUB-ASSEMBLY

Hide 11991A 18.INSTALL NO. 1 BALANCESHAFT THRUST PLATE

Hide 13560A 19.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 13519 20.INSTALL OIL PUMP DRIVE GEAR

a.

Install the oil pump drive gear to the crankshaft.


Hide 11324 21.INSTALL TIMING CHAIN COVER PLATE

Hide 11302 22.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new timing chain case gasket.


b.

Install the timing chain case gasket to the timing chain case assembly.


c.

Clean and degrease the contact surfaces of the timing chain cover sub-assembly and timing chain case assembly.


d.

Apply a coating of seal packing to the timing chain cover sub-assembly at the points shown in the illustration.

A339587C01
1.615,6.938 1.99,6.938 true 6.125,6.365 6.5,6.365 true 3.333,6.365 3.708,6.365 true 2.01,6.552 2.219,6.719 0.208,0.167 10 false *a 2.052,6.854 2.271,7.021 0.219,0.167 10 false *b 1.885,1.188 2.063,1.354 0.177,0.167 10 true A 2.375,1.167 2.552,1.333 0.177,0.167 10 true A 3.271,2.583 3.448,2.75 0.177,0.167 10 true B 2.792,2.5 2.969,2.667 0.177,0.167 10 true B 2.344,1.771 2.521,1.938 0.177,0.167 10 true C 3.479,0.51 3.656,0.677 0.177,0.167 10 true C 1.208,5.083 1.385,5.25 0.177,0.167 10 true C 3.167,5.365 3.479,5.542 0.313,0.177 10 true A-A 5.875,5.323 6.188,5.5 0.313,0.177 10 true B-B 3.719,5.844 3.927,6.01 0.208,0.167 10 false *a 3.76,6.271 3.979,6.438 0.219,0.167 10 false *b 6.406,5.833 6.615,6 0.208,0.167 10 false *a 6.542,6.271 6.76,6.438 0.219,0.167 10 false *b
*a 2.0 to 3.0 mm (0.0787 to 0.118 in.) *b 2.5 to 3.5 mm (0.0984 to 0.138 in.)


Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.


Standard seal packing diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Using non-residue solvent, clean and remove any oil from the installation surface.

·

Install the part within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine within 2 hours after installation.




e.

Temporarily install the timing chain cover sub-assembly with the 20 bolts.

A339589C01
0.042,0.031 0.271,0.208 0.229,0.177 10 false *a 3.583,0.052 3.813,0.219 0.229,0.167 10 false *b 0.927,0.167 1.083,0.333 0.156,0.167 10 true A 0.969,0.594 1.115,0.75 0.146,0.156 10 true B 1.458,1.198 1.604,1.354 0.146,0.156 10 true B 1.781,1.26 1.938,1.417 0.156,0.156 10 true B 2.563,1.292 2.708,1.448 0.146,0.156 10 true B 1.667,1.479 1.823,1.635 0.156,0.156 10 true B 1.323,1.51 1.479,1.677 0.156,0.167 10 true A 1.135,0.99 1.281,1.146 0.146,0.156 10 true B 0.781,1.917 0.938,2.083 0.156,0.167 10 true A 0.75,2.24 0.906,2.406 0.156,0.167 10 true A 0.854,2.542 1.01,2.708 0.156,0.167 10 true A 2.677,2.542 2.833,2.708 0.156,0.167 10 true A 2.896,2.229 3.042,2.375 0.146,0.146 10 true B 3.083,1.865 3.24,2.031 0.156,0.167 10 true A 3.24,1.552 3.406,1.708 0.167,0.156 10 true B 3.167,1.156 3.333,1.313 0.167,0.156 10 true B 2.875,0.156 3.031,0.323 0.156,0.167 10 true A 3.094,0.74 3.26,0.906 0.167,0.167 10 true B 2.469,0.573 2.615,0.719 0.146,0.146 10 true B 2.146,0.115 2.323,0.281 0.177,0.167 11 true B 5.854,1.26 6.021,1.427 0.167,0.167 10 true 1 6.542,1.563 6.688,1.708 0.146,0.146 10 true 2 6.385,1.854 6.531,2 0.146,0.146 10 true 3 6.177,2.229 6.333,2.385 0.156,0.156 10 true 4 5.99,2.552 6.146,2.708 0.156,0.156 10 true 5 4.188,2.531 4.344,2.688 0.156,0.156 10 true 6 4.063,2.24 4.219,2.396 0.156,0.156 10 true 7 4.073,1.906 4.229,2.063 0.156,0.156 10 true 8 4.635,1.51 4.792,1.667 0.156,0.156 10 true 9 4.948,1.5 5.135,1.656 0.188,0.156 10 true 10 5.083,1.271 5.271,1.427 0.188,0.156 10 true 11 4.771,1.198 4.958,1.344 0.188,0.146 10 true 12 4.375,0.99 4.563,1.135 0.188,0.146 10 true 13 4.271,0.594 4.458,0.74 0.188,0.146 10 true 14 4.177,0.177 4.365,0.323 0.188,0.146 10 true 15 5.406,0.135 5.594,0.281 0.188,0.146 10 true 16 6.167,0.156 6.365,0.313 0.198,0.156 10 true 17 6,0.573 6.198,0.729 0.198,0.156 10 true 18 6.385,0.75 6.583,0.906 0.198,0.156 10 true 19 6.49,1.156 6.688,1.313 0.198,0.156 10 true 20
*a Type of bolt *b Tightening


Bolt Length:
Item Length Thread Diameter
Bolt A 38 mm (1.50 in.) 8.0 mm (0.315 in.)
Bolt B 25 mm (0.984 in.) 8.0 mm (0.315 in.)



f.

Tighten the 20 bolts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

Check the torque of bolt 1 after tightening bolt 20.



Hide 12101 24.INSTALL OIL PAN SUB-ASSEMBLY

a.

Clean and degrease the contact surfaces of the oil pan sub-assembly and cylinder block sub-assembly.


b.
A339599C01
0,0 0,0 false
V100143

Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.5 mm (0.138 to 0.177 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 10 minutes after applying seal packing.

·

Do not add engine oil within 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.




c.
A339600C02
0.323,0.344 0.49,0.51 0.167,0.167 10 true A 0.948,0.052 1.115,0.219 0.167,0.167 10 true A 0.25,0.667 0.417,0.833 0.167,0.167 10 true A 0.188,1.104 0.354,1.271 0.167,0.167 10 true A 0.271,1.625 0.438,1.792 0.167,0.167 10 true A 0.688,1.938 0.854,2.104 0.167,0.167 10 true A 0.969,1.958 1.135,2.125 0.167,0.167 10 true A
V100135

Bolt
V100136

Nut


Install the oil pan sub-assembly to the cylinder block sub-assembly with the 23 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Check the torque of all nuts and bolts labeled A again.



Hide 89491 25.INSTALL ENGINE OIL LEVEL SENSOR

Hide 11201 26.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to the O-ring of the camshaft position sensor.


b.

Install a new cylinder head cover gasket, No. 2 cylinder head cover gasket and 2 camshaft bearing cap oil hole gaskets to the cylinder head cover sub-assembly.


c.

Clean and degrease the contact surfaces of the cylinder head cover sub-assembly and cylinder head sub-assembly.


d.

Apply seal packing as shown in the illustration.

A339583C01
2.5,1.406 2.969,1.406 true 0.51,2.344 0.51,1.698 true 1.354,2.333 1.354,1.073 true 6.052,1.156 6.521,1.156 true 4.375,0.375 5.333,0.375 true 0.469,3.698 0.698,3.104 0.698,3.104 0.844,3.104 true 1.354,4.979 1.354,4.271 true 2.938,4.979 2.813,4.979 2.813,4.979 2.406,4.563 true 0.427,2.396 0.646,2.563 0.219,0.167 10 false *1 1.281,2.385 1.49,2.542 0.208,0.156 10 true *2 3.052,1.323 3.26,1.5 0.208,0.177 10 false *3 6.604,1.073 6.823,1.24 0.219,0.167 10 false *4 0.792,0.302 1,0.469 0.208,0.167 10 true *a 2.51,1 2.719,1.188 0.208,0.188 10 true *b 0.302,1 0.51,1.167 0.208,0.167 10 true *c 5.917,0.156 6.104,0.323 0.188,0.167 10 true *d 1.875,0.313 2.083,0.479 0.208,0.167 10 true *a 6.719,0.521 6.927,0.688 0.208,0.167 10 true *a 6.719,1.667 6.927,1.833 0.208,0.167 10 true *a 5.927,2.01 6.115,2.177 0.188,0.167 10 true *d 4.135,0.292 4.344,0.448 0.208,0.156 10 true *3 0.896,3.479 1.104,3.646 0.208,0.167 10 true *a 1.885,3.49 2.094,3.656 0.208,0.167 10 true *a 2.375,4.135 2.583,4.323 0.208,0.188 10 true *b 0.406,4.156 0.615,4.323 0.208,0.167 10 true *c 0.917,3.021 1.135,3.188 0.219,0.167 10 false *1 1.271,5.01 1.479,5.167 0.208,0.156 10 true *2 3,4.906 3.208,5.083 0.208,0.177 10 false *3
*1 Timing Chain Cover Sub-assembly *2 Timing Chain Case Assembly
*3 Cylinder Head Sub-assembly *4 No. 3 Camshaft Bearing Cap
*a Seal Diameter: 3.0 to 6.0 mm (0.118 to 0.236 in.) *b Application Width: 7.0 mm (0.276 in.)
*c Application Width: 9.0 mm (0.354 in.) *d Application Width: 11.0 mm (0.433 in.)


Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 6.0 mm (0.118 to 0.236 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine within 2 hours after installation.




e.
A339609C04
0.448,0.958 0.625,1.125 0.177,0.167 10 true 6 0.563,0.031 0.76,0.208 0.198,0.177 10 true 15 0.948,0.052 1.167,0.24 0.219,0.188 10 true 11 1.354,0.104 1.573,0.292 0.219,0.188 10 true 9 1.917,0.115 2.146,0.302 0.229,0.188 10 true 13 2.552,0.073 2.771,0.26 0.219,0.188 10 true 17 3.125,0.021 3.333,0.188 0.208,0.167 10 true 19 0.052,0.719 0.208,0.896 0.156,0.177 10 true 5 0.469,1.396 0.625,1.563 0.156,0.167 10 true 3 1.042,1.375 1.24,1.552 0.198,0.177 10 true 1 1.656,1.365 1.844,1.542 0.188,0.177 10 true 2 2.26,1.375 2.438,1.552 0.177,0.177 10 true 4 2.833,1.5 3.01,1.667 0.177,0.167 10 true 7 0.156,2.01 0.365,2.177 0.208,0.167 10 true 18 0.396,1.99 0.604,2.156 0.208,0.167 10 true 14 0.802,1.99 1,2.156 0.198,0.167 10 true 10 1.323,1.927 1.531,2.104 0.208,0.177 10 true 8 1.885,1.917 2.104,2.094 0.219,0.177 10 true 12 2.469,1.917 2.688,2.094 0.219,0.177 10 true 16 3.104,1.958 3.302,2.135 0.198,0.177 10 true 21 0.104,0.01 0.302,0.188 0.198,0.177 10 true 20
V100135

Bolt
V100136

Nut
V100137

Nozzle Holder Clamp Seat


Tighten the 14 bolts, 4 nozzle holder clamp seats, 2 nuts and camshaft position sensor in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

When reusing the camshaft position sensor, check the O-rings.

·

Make sure that the O-ring is not cracked or jammed when installing it on the cylinder head cover sub-assembly.

·

Replace with a new part if it is dropped or if it receives a strong impact.

·

Check the torque of bolts 1 to 4 again.




Hide 23682 27.INSTALL NOZZLE HOLDER GASKET

Hide 23670 28.TEMPORARILY INSTALL INJECTOR ASSEMBLY

Hide 12501 29.INSTALL GENERATOR BRACKET SUB-ASSEMBLY

Hide 12281A 30.INSTALL NO. 1 ENGINE HANGER

Hide 16575C 31.INSTALL NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)

Hide 13471 32.INSTALL CRANKSHAFT PULLEY (for Automatic Transmission)

Hide 13407 33.INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY (for Manual Transmission)

Hide 13496 34.INSTALL CRANKSHAFT PULLY COVER (for Automatic Transmission)

Hide 88451B 35.INSTALL VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

Hide 16620 36.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.

Install the V-ribbed belt tensioner assembly to the timing chain cover sub-assembly with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16603 37.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.

Install the No. 1 idler pulley sub-assembly to the generator bracket sub-assembly with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16304 40.INSTALL WATER OUTLET SUB-ASSEMBLY

Hide 16207 41.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 15407 42.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 17141 43.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

Hide 17141 46.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

Hide 87101 48.INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

Hide 16268 50.INSTALL NO. 1 WATER BY-PASS PIPE

Hide 51.INSTALL WATER BY-PASS HOSE (for Water Cooled Compressor Housing Turbocharger)

Hide 12261 53.INSTALL PCV HOSE (except Cold Area Specification Vehicles)

Hide 89463C 54.INSTALL NO. 1 NITROGEN OXIDES SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)

Hide 17291 55.INSTALL TURBINE OUTLET ELBOW (w/o EGR Cooler)

Hide 57.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY (w/o DPF)

Hide 58.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY (w/ DPF)

Hide 89463C 59.CONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)

Hide 17167 62.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o DPF)

Hide 17167 63.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)

Hide 89467B 64.INSTALL AIR FUEL RATIO SENSOR (w/o Exhaust Gas Temperature Sensor for EGR)

Hide 16281 66.CONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)

Hide 16282 67.INSTALL NO. 5 WATER BY-PASS HOSE (w/ DPF)

Hide 12229 68.INSTALL PCV PIPE (for Cold Area Specification Vehicles)

Hide 16632B 69.INSTALL NO. 2 IDLER PULLEY BRACKET (w/o Air Conditioning System)

Hide 88431 70.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

Hide 88320 71.INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 23701 73.TEMPORARILY INSTALL NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23670 74.TIGHTEN INJECTOR ASSEMBLY

Hide 23701 75.TIGHTEN NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 76.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 23760 77.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 79.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 23770 81.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 23804C 82.INSTALL FUEL INLET PIPE SUB-ASSEMBLY

Hide 23815D 83.INSTALL NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23804D 84.INSTALL NO. 4 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23804D 85.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)

Hide 23271H 86.INSTALL NO. 1 FUEL HOSE

Hide 23273H 87.INSTALL NO. 2 FUEL HOSE

Hide 23243B 88.INSTALL FUEL PUMP MOTOR WIRE

Hide 22803 89.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 91.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 11409 93.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 25624 94.INSTALL EGR VALVE ADAPTER (w/o EGR System)

Hide 95.INSTALL EGR VALVE ADAPTER SUB-ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)

Hide 25800 96.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System with EGR Cooler)

Hide 16209 97.INSTALL NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 25804 98.INSTALL VACUUM CONTROL VALVE SET (w/ EGR Cooler)

Hide 25601 99.INSTALL EGR PIPE WITH COOLER SUB-ASSEMBLY (for Laminated EGR Pre-cooler)

Hide 25601 100.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System)

Hide 16206B 102.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/o EGR Cooler)

Hide 16206B 103.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ EGR Cooler)

Hide 89425D 105.INSTALL NO. 5 EXHAUST GAS TEMPERATURE SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)

Hide 12631A 109.INSTALL ENGINE COVER BRACKET

Hide 25734 111.TEMPORARILY INSTALL NO. 2 VACUUM PIPE (w/ DPF)

Hide 25733A 112.TEMPORARILY INSTALL NO. 1 VACUUM PIPE (w/ DPF)

Hide 89425 115.INSTALL EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 89481B 116.INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ DPF)

Hide 26100G 118.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 82121 119.INSTALL ENGINE WIRE

Hide 12632 120.INSTALL NO. 2 ENGINE COVER BRACKET (for Air Cooled Type Intercooler)