Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2020.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0382589 ECD SYSTEM(w/ Urea SCR System) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  Engine Difficult to Start or Stalling  


DESCRIPTION

Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Mass Air Flow Meter Sub-assembly
Main fault Decrease in performance (foreign matter is stuck)
Symptoms Lack of power, black smoke
Data List Mass Air Flow Sensor
HINT:

The maximum injection volume is controlled according to the output from the mass air flow meter sub-assembly.



Intake System
Symptom and Corresponding Main Fault
·

Lack of power (no black smoke) due to air cleaner filter element blockage or crushed or leaking air duct

·

Black smoke (no lack of power) due to leakage between the turbocharger and intake manifold


Data List Intake Manifold Absolute Pressure

Turbocharger System
Main fault
·

Air leak in the turbocharged air passage

·

ECM not operating well

·

Turbocharger (turbine, bearing)


Symptoms Lack of power (when vehicle is starting, under heavy load)
(Black smoke is not emitted when racing while vehicle is stopped)
Data List Intake Manifold Absolute Pressure
·

With the ignition switch ON or during idling, Intake Manifold Absolute Pressure = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and Intake Manifold Absolute Pressure becomes higher than atmospheric pressure.

·

Atmospheric pressure decreases by 1 kPa each time elevation increases by 100 m, and is also affected by the current weather conditions.



Exhaust System
Main fault Blockage
Symptoms Lack of power (high engine speed, under heavy load)

Glow System
Main fault Glow system malfunction
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Diagnostic Point
·

Measure the resistance of the glow plug assembly

·

Check the glow plug indicator light



Battery
Main fault Battery is depleted
Symptoms Difficult to start (cannot crank, crank speed is low), horn is quiet
Data List Battery Voltage
·

When cranking, battery voltage is below 5 V.



Engine - 1
Main fault Damaged, seized up
Symptoms Cannot crank, crank speed is low, strange noise

Engine - 2
Main fault Loss of compression
Symptoms Rough idle (lack of power always)
Data List Engine Speed Cylinder
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.


Injection Feedback Value
·

When an Injector Feedback Val is more than 5 mm3/st, there may be a malfunction in the corresponding cylinder.



Start System
Main fault Starter system malfunction
Symptoms Difficult to start
Data List Starter SW
·

Ignition switch (STA) output:

ON: Starter is operating

OFF: Starter is not operating




b.

Diesel Injection

Fuel Supply Pump Assembly
Main fault -
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Pressure (High), Target Fuel Pressure (High)
·

Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High) during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).

·

If the fuel pressure is 20000 kPag below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPag, then idling will be rough.


HINT:

The fuel pressure changes at engine start, but is approx. 25000 kPag at engine start after the engine is warmed up.


Diagnostic Trouble Code Even if Fuel Pressure (High) is below Target Fuel Pressure (High), a DTC will not be stored.

Fuel Filter Element Assembly
Main fault Blockage
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Pressure (High), Target Fuel Pressure (High)
·

Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High) during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).

·

If the fuel pressure is 20000 kPag below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPag, then idling will be rough.


HINT:

The fuel pressure changes at engine start, but is approx. 25000 kPag at engine start after the engine is warmed up.


Diagnostic Trouble Code Even if Fuel Pressure (High) is below Target Fuel Pressure (High), a DTC will not be stored.

Injector Assembly
Main fault Blockage
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Value
·

When an Injector Feedback Value is more than 5 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.



Pressure Discharge Valve
Main fault Does not completely close
Symptoms Difficult to start, engine stall, rough idle, lack of power

Fuel Pressure Sensor
Main fault Open circuit, decrease in performance (foreign matter is stuck)
Symptoms Difficult to start, rough idle, engine stall, lack of power
Data List Fuel Pressure (High), Target Fuel Pressure (High)
·

Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Fuel Pressure (High) follows Target Fuel Pressure (High). If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Fuel Pressure (High) decreases to a value less than Target Fuel Pressure (High)).


Diagnostic Trouble Code When the fuel pressure sensor has a fault, some DTCs may be stored.

Irregular Fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)


c.

Diesel EGR

EGR System
Main fault
·

Does not move smoothly

·

Does not close completely


Symptoms
·

Rough idle

·

EGR valve stuck closed: A loud turbocharger sound.

·

EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).


Data List Actual EGR Valve Position No.1, Target EGR Valve Position No.1
·

Generally, Actual EGR Valve Position No.1. = Target EGR Position +/-5% (fully closed: 0%, fully open: 100%).

·

Using the EGR valve Active Test, check whether Actual EGR Valve Position No.1. follows Target EGR Valve Position No.1 (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).

·

EGR valve is fully closed when the ignition switch is turned to ON (engine stopped).

·

EGR valve opens to the halfway point at idling after the engine is warmed up.


EGR Close Learning Value Bank 1
·

When leaving the vehicle idling, the normal range of EGR Close Learning Value Bank 1 is 0 to 1 V.

·

In cases when EGR Close Learning Value Bank 1 is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.




d.

Diesel Throttle

Diesel Throttle System
Main fault Stuck, does not move smoothly
Symptoms
·

Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.

·

Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.


Data List Actual Throttle Position Bank 1
·

0%: Fully closed

·

100%: Fully open

·

When the ignition switch is ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily.





Data List Related to Startability Malfunctions and Engine Stalls


HINT:

Depending on the vehicle model, the applicable Data List items may vary. Data List items other than the ones used in the diagnostic procedure are for reference only.

·

Intake Manifold Absolute Pressure

·

Mass Air Flow Sensor

·

Intake Air Temperature

·

Coolant Temperature

·

Battery Voltage

·

Starter SW

·

Engine Speed Cylinder #1 to #4

(Output only when the "Check the Cylinder Compression" Active Test is performed)

·

Target Fuel Pressure (High)

·

Fuel Pressure (High)

·

Injection Feedback Value #1 to #4

·

Target Injection Volume

·

Actual Throttle Position Bank 1

·

Target EGR Valve Position No.1

·

Actual EGR Valve Position No.1

·

EGR Close Learning Value Bank 1




Vehicle Control History Freeze Frame Data Items Related to Startability Malfunctions and Engine Stalls


HINT:

The frequency of the malfunction can be determined by confirming the number of times the symptom occurred.

·

Engine Stall Count

·

Engine Stall Count (Fuel Pressure Low)

·

Engine Difficult to Start Count (Engine Starting Time Long)

·

Engine Difficult to Start Count (Engine Stall Immediately After Starting)

·

Engine Difficult to Start Count (Immobiliser)




CAUTION / NOTICE / HINT

Explanation of Symptom



Starting Trouble For good starting it is essential to have:
·

Sufficient cranking speed.

·

Properly operating engine preheating system.

·

Good quality fuel.


The fuel is ignited by the heat which is generated by compression pressure.
With problems such as a depleted battery, the crankshaft speed can become low, or if the engine compression is poor due to leakage, the compression pressure will not rise and there will be difficulty starting.
When the engine is cold, even if there is compression heat, it will escape from the combustion chamber. For this reason, when the engine is started when it is cold, the glow plug assemblies heat the compressed air.
Also, after starting the engine, by charging the glow plug assemblies for a fixed time set according to the engine coolant temperature, diesel knocking and white smoke are prevented. The quantity of fuel injected is determined by the fuel pressure and also the amount of time the injector assembly is open.

Trouble Area Chart According to Problem Cause



A409061E08
0.271,0.146 3.021,0.344 2.75,0.198 10 false Difficult to start 0.875,1 3.625,1.198 2.75,0.198 10 false Does not crank at all 3.615,1.083 6.365,1.281 2.75,0.198 10 false Depleted battery 3.615,1.865 6.365,2.063 2.75,0.198 10 false ECM power supply circuit malfunction 3.646,2.76 5.802,3.219 2.156,0.458 10 false Immobiliser system or fault 0.813,4.146 3.563,4.344 2.75,0.198 10 false Cranking speed too slow 3.667,4.135 6.417,4.333 2.75,0.198 10 false Depleted battery 3.531,4.948 6.188,5.688 2.656,0.74 10 false Increased internal friction of the engine mechanical parts (oil too thick, seizure, etc.) 0.76,5.646 3.51,5.844 2.75,0.198 10 false Difficult to start (cranking is OK) 1.708,6.583 4.458,6.781 2.75,0.198 10 false Fuel pressure is low 4.156,6.563 6.906,6.76 2.75,0.198 10 false Fuel is not supplied to fuel supply pump 4.188,7.333 6.938,7.531 2.75,0.198 10 false Fuel supply pump malfunction 4.177,8.125 6.927,8.323 2.75,0.198 10 false Common rail assembly malfunction 0.833,8.563 3.583,8.76 2.75,0.198 10 false A

A183464E28
0.844,0.094 1,0.26 0.156,0.167 10 false A 4.188,0.76 7.115,1.083 2.927,0.323 10 false Injector power source circuit malfunction 1.76,0.781 3.177,1.01 1.417,0.229 10 false Fuel pressure is high 4.177,1.531 5.781,1.875 1.604,0.344 10 false Air in injector assembly 4.198,2.375 6.167,2.656 1.969,0.281 10 false Injector assembly malfunction 1.771,2.385 3.229,2.646 1.458,0.26 10 false Specific cylinder fault 4.188,3.135 6.031,3.438 1.844,0.302 10 false Low compression pressure 4.188,3.979 6,4.25 1.813,0.271 10 false Glow system malfunction 1.76,3.99 3.448,4.271 1.688,0.281 10 false Difficult to start when cold 4.177,4.76 6.323,5.208 2.146,0.448 10 false Engine coolant temperature sensor malfunction 1.76,6.125 2.896,6.396 1.135,0.271 10 false Poor fuel quality

NOTICE:
·

After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION).



HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


HINT:
·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Make sure to reproduce the conditions present when the malfunction occurred.

·

Using the GTS, read the Data List to confirm the engine operating conditions. This information can be useful when troubleshooting.

·

The vehicle condition when the problem symptoms occurred can be determined using the Vehicle Control History.

·

As the Vehicle Control History data may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.

·

If the problem symptoms do not recur, attempt to reproduce the symptoms and conditions when the malfunction occurred based on the result of the customer problem analysis and Vehicle Control History. Place the priority on confirming the symptoms.

·

When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.

·

The suspected cause of the problem symptoms can be determined using the codes, items, and Freeze Frame Data within the Vehicle Control History.

·

When confirming the Freeze Frame Data, be sure to check all multi Freeze Frame Data.

·

When confirming the Freeze Frame Data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.

·

If the malfunction is currently occurring, use the Data List to confirm the current vehicle condition. By using the Data List, more detailed vehicle information can be confirmed than by using the Vehicle Control History Freeze Frame Data by itself.

·

As Vehicle Control History may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History before returning the vehicle to the customer.



PROCEDURE

1.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.

Result:
Result Proceed to
Cranking is OK. A
Low cranking speed.
HINT:

When cranking speed is low, especially when the temperature is low, check if the engine oil grade matches the recommendation.


B
Does not crank at all. C




A

2.READ ALL OUTPUT DTCS

B

C

33.READ OUTPUT DTC (RELATED TO ENGINE)
2.READ ALL OUTPUT DTCS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: System Select / Health Check.


d.

Check the DTCs.

Result:
Result Proceed to
No DTC is output A
Engine related DTCs are output B




A

3.READ VEHICLE CONTROL HISTORY FREEZE FRAME DATA

B

3.READ VEHICLE CONTROL HISTORY FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55
HINT:

It is also possible to display Vehicle Control History during the Health Check, if "Store All Data" is selected.



e.

Confirm if any data relating to the problem symptoms exist in the Vehicle Control History.

HINT:
·

The vehicle condition when the problem symptoms occurred can be determined by confirming the Vehicle Control History Freeze Frame Data.

·

As the Vehicle Control History data may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.

·

Using information from the customer about when the problem symptom occurred, find the Freeze Frame Data with the appropriate Key Cycle, Total Distance Traveled, etc., to find vehicle history that may be related to the problem symptoms.




f.

Check the vehicle control history code and freeze frame data.

Result:
Vehicle Control History Vehicle Control History Freeze Frame Data Suspected Area Proceed to
Engine Stall is stored
(Vehicle Control History Code: X0800)
"BATT Voltage" in freeze frame data is below 6 V The battery may be fully depleted or the battery terminals may be loose. B
- - A
Engine Stall (Fuel Pressure Low) is stored
(Vehicle Control History Code: X0806)
"Fuel Pressure (High)" in freeze frame data is below 25000 kPag (254.9 kgf/cm2, 3626 psi) Problem supplying fuel to fuel supply pump assembly (low pressure side)
·

Ran out of fuel, air in fuel, fuel frozen (in this case, values of "Coolant Temperature" in freeze frame data are low)

·

Fuel filter element clog, fuel line clog (low pressure side) or fuel leak

·

Feed pump (in fuel supply pump assembly) malfunctioning


Problem supplying fuel to fuel supply pump assembly (low pressure side) or problem on high pressure side
·

Fuel supply pump assembly (pre-stroke control valve operation malfunction)

·

Common rail assembly


C
Engine Stall (Engine Starting Time Long) is stored
(Vehicle Control History Code: X0810)
"Coolant Temperature" in freeze frame data is below 35°C (95°F) Engine starting trouble which occurred with cold engine D
"Engine Speed" in freeze frame data is less than 120 rpm Engine starting trouble may have occurred because engine speed was too low
·

The battery may be fully depleted or the battery terminals may be loose.

·

The viscosity of the engine oil may be inappropriate (low viscosity oil is not used).


B
"BATT Voltage" in freeze frame data is below 6 V Engine starting trouble may have occurred because battery is fully depleted
"Fuel Pressure (High)" in freeze frame data is below 10000 kPag Problem supplying fuel to fuel supply pump assembly (low pressure side)
·

Ran out of fuel, air in fuel, fuel frozen (in this case, values of "Coolant Temperature" in freeze frame data are low)

·

Fuel filter element clog, fuel line clog (low pressure side) or fuel leak

·

Feed pump (in fuel supply pump assembly) malfunctioning


C
"Fuel Pressure (High)" in freeze frame data is below 25000 kPag Problem supplying fuel to fuel supply pump assembly (low pressure side) or problem on high pressure side
·

Fuel supply pump assembly (Pre-stroke control valve operation malfunction)

·

Common rail Assembly

·

Injector assembly (if glow plug assembly is covered with fuel when removed, injector of corresponding cylinder may be stuck open)

·

Fuel line clog (high pressure side), fuel leak


E
- - A
Engine Stall (Engine Stall Immediately After Starting) is stored
(Vehicle Control History Code: X0811)
- - A
Engine Difficult to Start (Immobiliser) is stored
(Vehicle Control History Code: X0812)
-
·

Inspect engine immobiliser system.

·

Inspection looseness in battery terminal.

·

Inspect connection condition of ECM power supply system wiring.


-
The malfunction is not currently occurring and there is no Vehicle Control History related to the problem symptoms stated by the customer. A




A

4.TAKE SNAPSHOT DURING STARTING AND IDLING (PROCEDURE 4)

B

C

6.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY

D

30.READ VALUE USING GTS (COOLANT TEMPERATURE)

E

7.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)
4.TAKE SNAPSHOT DURING STARTING AND IDLING (PROCEDURE 4)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Starting.


d.

Take a snapshot when idling with no load after the engine is warmed up and when starting trouble is occurring.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.

·

When there is trouble starting with a cold engine, take the snapshot when the engine is cold. Then warm up the engine (engine coolant temperature is 75°C (167°F) or higher) and after idling the vehicle for 1 minute (A/C off, electrical load off), take a snapshot of the data for 15 seconds while idling.

·

Take a snapshot when the problem is occurring, such as when the engine is cold. However, if the problem does not reoccur, it is acceptable to only take a snapshot after the engine is warmed up and when the engine is started.




Result:
Proceed to
NEXT



NEXT

5.CHECK SNAPSHOT (COMMON RAIL PRESSURE)
5.CHECK SNAPSHOT (COMMON RAIL PRESSURE)
a.

Check Fuel Pressure (High) in the snapshot taken in procedure 4 when the engine was started.

A227761E37
2.385,0.844 2.469,0.844 2.469,0.844 2.417,1.188 false 2.813,0.542 2.74,0.594 false 4.146,0.583 4.021,0.583 4.021,0.583 3.802,0.771 false 4.01,2.344 3.917,2.344 3.917,2.344 3.802,2.229 false 3.938,2.875 3.865,2.875 3.865,2.875 3.792,2.792 false 5.563,0.406 5.406,0.406 5.406,0.406 5.094,0.927 false 5.667,1.469 5.573,1.469 5.573,1.469 5.417,1.24 false 5.594,2.177 5.479,2.177 5.479,2.177 5.25,1.51 false 1.938,2.333 2.083,2.333 2.083,2.333 2.281,2.99 false 5.292,2.646 5.479,2.177 false 0.052,1.74 0.906,2.198 0.854,0.458 10 false Fuel Pressure (High) 3.969,2.792 4.104,2.969 0.135,0.177 10 false a 2.844,0.469 2.99,0.646 0.146,0.177 10 false b 4.198,0.5 4.365,0.667 0.167,0.167 10 false d 4.052,2.271 4.198,2.448 0.146,0.177 10 false c 1.073,0.771 2.344,1.135 1.271,0.365 10 false Target Fuel Pressure (High) 5.594,0.344 7.063,0.698 1.469,0.354 10 false Abnormal Fuel Pressure 1.083,2.229 1.99,2.833 0.906,0.604 10 false Engine Cranking Start 2.469,3.198 3.573,3.375 1.104,0.177 10 false About 2 seconds 5.594,2.104 7.083,2.479 1.49,0.375 10 false Abnormal Fuel Pressure 5.719,1.417 7.042,1.781 1.323,0.365 10 false Normal Fuel Pressure

Result:
Result Proceed to
At the point in the illustration labeled "a", Fuel Pressure (High) is less than 10000 kPag from the value of Fuel Pressure (High) when cranking started A
At the point in the illustration labeled "c", Fuel Pressure (High) is below Target Fuel Pressure (High) by 15000 kPag or more B
Fuel Pressure (High) increases to a value that is higher than Target Fuel Pressure (High) immediately after cranking, and, at the point in the illustration labeled "d", Fuel Pressure (High) is higher than Target Fuel Pressure (High) C
Except above D


HINT:
·

Even if Fuel Pressure (High) is temporarily higher than Target Fuel Pressure (High), as shown at the point in the illustration labeled "b", the fuel supply pump assembly is normal.

·

Fuel pressure is about 25000 to 35000 kPag when the engine is cranking and the engine coolant temperature is 0°C (32°F) or higher.

·

Fuel Pressure (High) increases rapidly during cranking.





A

6.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY

B

14.READ VALUE USING GTS (FUEL PRESSURE (HIGH))

C

17.INSPECT INJECTOR POWER SOURCE CIRCUIT

D

20.CHECK DATA LIST (INJECTOR FEEDBACK VALUE #1 TO #4 AND TARGET INJECTION VOLUME)
6.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY
a.

Disconnect the inlet hose from the fuel supply pump assembly.


b.

Operate the priming pump and check that fuel is being supplied to the fuel supply pump assembly.

OK:

Fuel is properly supplied to the fuel supply pump when the priming pump is operated.


HINT:
·

When there is a lack of fuel, fuel pressure drops.

·

Inspect for fuel filter element assembly clogging (check that the fuel filter element assembly is not clogged).




c.

Reconnect the inlet hose.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)

NG

12.CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)
a.

Disconnect the pre-stroke control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E102-1 (+B) - E6-3 (PCV+) Always Below 1 Ω
E102-2 (PCV) - E6-4 (PCV-) Always Below 1 Ω
E102-1 (+B) or E6-3 (PCV+) - Body ground and other terminals Always 10 kΩ or higher
E102-2 (PCV) or E6-4 (PCV-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE FUEL SUPPLY PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.BLEED AIR FROM FUEL SYSTEM
9.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

10.READ VALUE USING GTS (FUEL PRESSURE (HIGH) AND STARTER SW)
10.READ VALUE USING GTS (FUEL PRESSURE (HIGH) AND STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Starting / Fuel Pressure (High) and Starter SW.

Powertrain > Engine > Data List
Tester Display
Fuel Pressure (High)
Starter SW
50003 372 265,11

d.

Start the engine.


e.

Read the values while cranking and idling the engine.

Result:
Result Proceed to
The engine cannot be started or the engine can be started but Fuel Pressure (High) is below 20000 kPag 2 seconds after the Starter SW changes from OFF to ON B
Except above A




A

END

B

11.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
11.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
a.

Remove the glow plug assembly assembly for all the cylinders.

Click hereEngine / Hybrid System>1GD-FTV (STARTING)>GLOW PLUG>REMOVAL


b.

Visually check if there is fuel on the glow plug assemblies.

HINT:
·

If there is fuel on a glow plug assembly, fuel may be leaking from an injector assembly.

·

After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPag of the target fuel pressure while cranking the engine.

·

If there is fuel on a glow plug assembly, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.




c.

Install the glow plug assembly.

Click hereEngine / Hybrid System>1GD-FTV (STARTING)>GLOW PLUG>INSTALLATION


Result:
Proceed to
NEXT



NEXT

24.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
12.CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP ASSEMBLY)
a.

Check and repair or replace the clogged fuel pipe.


Result:
Proceed to
NEXT



NEXT

13.BLEED AIR FROM FUEL SYSTEM
13.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

28.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.READ VALUE USING GTS (FUEL PRESSURE (HIGH))
a.

Check Fuel Pressure (High) in the snapshot taken in procedure 4 when the engine was warmed up.

Result:
Result Proceed to
Difference between Fuel Pressure (High) and Target Fuel Pressure (High) is 5000 kPag (51.0 kgf/cm2, 725 psi) or more A
Except above B




A

15.REPLACE FUEL SUPPLY PUMP ASSEMBLY

B

16.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
15.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
16.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies of all cylinders.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

25.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
17.INSPECT INJECTOR POWER SOURCE CIRCUIT
a.

Perform troubleshooting for DTC P062D96 during a startability malfunction, even if P062D96 is not output.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P020112

When troubleshooting the injector power source circuit, check the following locations, as one may contain the cause of the malfunction

·

EDU relay

·

Injector assembly circuit

·

ECM


HINT:
·

When the engine cannot be started due to a malfunction in the injector power source circuit, once the DTCs are cleared, P062D96 cannot be stored even when the problem symptoms are reproduced and a startability malfunction occurs.

Since P062D96 cannot be stored when starting the engine, fuel injection cannot be performed even though fuel injection signals are output from the ECM. Therefore, using the GTS during a startability malfunction to check the data shows that an excessive amount of fuel is supplied to the common rail assembly by the fuel supply pump assembly, and as a result, the Fuel Pressure (High) is higher than the Target Fuel Pressure (High).

·

Perform the following procedure when a malfunction cannot be found during the troubleshooting procedure for P062D96 and the Fuel Pressure (High) when starting the engine is higher than the Target Fuel Pressure (High).

·

Perform the troubleshooting procedure for DTC P062D96 and proceed to the diagnostic flow situations where the engine does not start.




Result:
Result Proceed to
Injector power source circuit is normal A
Injector power source circuit is abnormal B



A

18.INSPECT INJECTOR ASSEMBLY

B

REPAIR OR REPLACE MALFUNCTIONING PARTS

18.INSPECT INJECTOR ASSEMBLY
a.

Disconnect the injector assembly connectors.


b.

Measure the resistance of the injector assembly.

OK:

No open circuit malfunction.



Result:
Proceed to
OK
NG



OK

37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

19.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
19.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

25.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
20.CHECK DATA LIST (INJECTOR FEEDBACK VALUE #1 TO #4 AND TARGET INJECTION VOLUME)
a.

Check Injection Feedback Value #1 to #4 and Target Injection Volume in the snapshot taken in procedure 4 when the engine was idling.

Result:
Result Proceed to
Injection Feedback Value #1 to #4 are 5 mm3/st or less.
Target Injection Volume is more than 15 mm3/st.
A*
Injection Feedback Value for at least one cylinder is more than +5 mm3/st
HINT:

There may be a malfunction in the corresponding cylinder.


B
Except above C


HINT:
·

*: When this case occurs, usually symptoms may be noticeable, such as difficulty starting or lack of power.

·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.





A*

21.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

B

22.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

C

29.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS
21.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies of all cylinders.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

25.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
22.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed Cylinder #1 to #4.

Powertrain > Engine > Active Test
Active Test Display
Check the Cylinder Compression
Data List Display
Engine Speed Cylinder #1
Engine Speed Cylinder #2
Engine Speed Cylinder #3
Engine Speed Cylinder #4
50004 372 42028 134,135,136,137

d.

Check the engine speed during the Active Test.

Result:
Result Proceed to
Except below A
The values of Engine Speed Cylinder #1 to #4 are within 10 rpm of each other. B


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.




A

23.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

B

19.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
23.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
HINT:

Measure the compression of the cylinder that had a high speed during the "Check the Cylinder Compression" Active Test.


a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

24.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

24.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
HINT:

It can be determined that the injector assembly is faulty as the corresponding cylinder is malfunctioning, but has no compression loss.


a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

25.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
25.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

26.BLEED AIR FROM FUEL SYSTEM
26.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

27.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
27.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation codes.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Injector Compensation
50005 372 4596

b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Pilot Quantity Learning
50005 372 4569

Result:
Proceed to
NEXT



NEXT

28.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
28.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END

29.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS
a.

Check the temperature when starting trouble occurs.

Result:
Result Proceed to
Difficult to start only for cold engine. A
Difficult to start both for cold and warmed up engine. B




A

30.READ VALUE USING GTS (COOLANT TEMPERATURE)

B

32.CHECK FUEL QUALITY
30.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Starting / Coolant Temperature.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205

d.

Read the value displayed on the GTS.

OK:

Coolant Temperature is not high when the engine is cold, and not low after the engine is warmed up.



Result:
Proceed to
OK
NG



OK

31.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

NG

31.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

Result:
Proceed to
OK
NG



OK

32.CHECK FUEL QUALITY

NG

32.CHECK FUEL QUALITY
a.

Check that only diesel fuel is being used.


b.

Check that the fuel does not contain any impurities.


Result:
Proceed to
NEXT



NEXT

37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
33.READ OUTPUT DTC (RELATED TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
Engine related DTCs are output B




A

34.CHECK COMMUNICATION BETWEEN GTS AND ECM

B

34.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Check if the normal starting screen appears (check whether communication with the ECM is possible).

HINT:

Use a GTS that is able to communicate with other vehicles.


OK:

Communication is possible (vehicle can be recognized).



Result:
Proceed to
OK
NG



OK

35.READ VALUE USING GTS (STARTER SW AND NEUTRAL POSITION SW)

NG

35.READ VALUE USING GTS (STARTER SW AND NEUTRAL POSITION SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Primary / Starter SW and Neutral Position SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
Neutral Position SW
50003 372 11,20

d.

Read the value displayed on the GTS.

OK:
GTS Display Condition Specified Condition
Starter SW Cranking ON
Neutral Position SW Shift lever in neutral ON



Result:
Result Proceed to
OK A
NG B



A

36.CHECK STARTING SYSTEM

B

36.CHECK STARTING SYSTEM
a.

Inspect the starting system.

HINT:

Be sure to inspect the following areas:

·

Battery

·

Starter relay

·

Starter assembly

·

Immobiliser system




Result:
Proceed to
NEXT



NEXT

37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END