The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel supply pump assembly removal/installation are shown below.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
| Injector assembly (including shuffling the injector assemblies between the cylinders) | ·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
| Supply pump assembly | Fuel inlet pipe sub-assembly |
·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Timing chain case assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.
Make sure foreign matter does not enter the fuel path.
1. PRECAUTION
After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
17111
3.REMOVE INTAKE MANIFOLD
51406A
4.REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)
52618
5.REMOVE LOWER FRONT BUMPER ABSORBER
51405A
6.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
17030
7.REMOVE AIR HOSE ASSEMBLY (for Air Cooled Type Intercooler)
25761B
8.DISCONNECT NO. 1 VACUUM TRANSMITTING HOSE (for Air Cooled Type)
17303T
9.REMOVE AIR PIPE SUB-ASSEMBLY (for Air Cooled Type Intercooler)
53106B
10.REMOVE RADIATOR COVER SUB-ASSEMBLY
17751
11.REMOVE NO. 1 AIR CLEANER INLET
44360
12.DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY
16640
13.REMOVE INTERCOOLER RESERVE TANK ASSEMBLY (for Water Cooled Type Intercooler)
16470
14.REMOVE RADIATOR RESERVE TANK ASSEMBLY
16571C
15.REMOVE NO. 1 RADIATOR HOSE
16552C
16.REMOVE NO. 2 INTERCOOLER COOLING WATER HOSE (for Water Cooled Type Intercooler)
16551C
17.REMOVE NO. 1 INTERCOOLER COOLING WATER HOSE (for Water Cooled Type Intercooler)
161B0
18.REMOVE ELECTRIC WATER PUMP ASSEMBLY (for Water Cooled Type Intercooler)
88359
19.REMOVE VISCOUS HEATER V BELT (w/ Viscous Heater)
20.DISCONNECT INTERCOOLER COOLING WATER PIPE ASSEMBLY (for Water Cooled Type Intercooler)
16711
21.REMOVE FAN SHROUD
16620
22.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
23273H
23.REMOVE NO. 2 FUEL HOSE
Slide the 2 clips and remove the No. 2 fuel hose from the supply pump assembly and No. 3 nozzle leakage pipe assembly.
23271H
24.REMOVE NO. 1 FUEL HOSE
Slide the 2 clips and remove the No. 1 fuel hose from the supply pump assembly and No. 2 fuel pipe.
25.REMOVE NO. 4 FUEL PIPE (w/ Pressurized Fuel Filter without DPF)
Remove the No. 4 fuel pipe 2 union bolts and 2 gaskets from the supply pump assembly and fuel filter.
22803
26.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY
Remove the fuel injection pump cover sub-assembly from the supply pump assembly.
23243B
27.REMOVE FUEL PUMP MOTOR WIRE
Disconnect the fuel pump motor wire connector.
Detach the clamp and remove the fuel pump motor wire.
11324
28.REMOVE TIMING CHAIN COVER PLATE
Remove the 3 bolts and timing chain cover plate.
Remove the gasket.
22100
29.REMOVE SUPPLY PUMP ASSEMBLY
| *A | w/ Pressurized Fuel Filter |
| *B | w/o Pressurized Fuel Filter |
Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.
With SST set, do not turn the crankshaft more than a half rotation.
| *a | Timing Mark |
Align the timing mark of the crankshaft pulley sub-assembly and timing chain cover by rotating the crankshaft clockwise.
| *a | Hold |
|
Turn |
Using SST, hold the crankshaft pulley assembly and loosen the fuel supply pump shaft nut.
Do not excessively loosen the supply pump shaft nut, otherwise SST cannot be installed.
Rotate the supply pump shaft nut once to loosen it.
| *A | w/ Pressurized Fuel Filter |
| *B | w/o Pressurized Fuel Filter |
Loosen the 3 nuts from the supply pump assembly.
Do not completely remove the nuts. Otherwise, the supply pump assembly may fall off.
Install SST with 3 bolts.
Install SST with the bolts included with SST.
| *a | Engine Front Side |
| *b | Engine Rear Side |
| *c | SST Hexagonal Portion |
Make sure that the installation direction of SST is as shown in the illustration.
Align the hexagonal portion of SST with the supply pump shaft nut to install SST.
Remove the 2 bolts and No. 1 fuel pump bracket from the supply pump assembly and cylinder block sub-assembly.
| *a | Hold |
|
Turn |
Install the handle to SST. While holding the crankshaft pulley assembly in place with the crankshaft holding tool, turn the handle in the counterclockwise direction to disconnect the supply pump assembly.
Remove the 3 nuts and supply pump assembly from the timing chain case assembly.
Remove the O-ring from the supply pump assembly.