Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1429    Open or Short in Brake Pedal Load Sensing Switch

for Preparation Click here


DESCRIPTION

The brake pedal load sensing switch is turned on when the brake pedal is depressed with force exceeding a predetermined level.
The skid control ECU detects if the brake pedal is depressed or not via this circuit.

DTC Code
DTC Detection Condition
Trouble Area
C1429
An open or short in the brake pedal load sensing switch continues for 0.3 seconds or more.
  1. Brake pedal load sensing switch
  2. Brake pedal load sensing switch circuit
  3. Brake actuator assembly (Skid control ECU)

WIRING DIAGRAM


C168343E01


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).

HINT:
When C1425 and/or C1426 is output together with C1429, inspect and repair the trouble areas indicated by C1425 and/or C1426 first (Click here, or Click here).

1.READ VALUE ON TECHSTREAM (BRAKE PEDAL LOAD SENSING SWITCH)
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Select the Data List mode on Techstream (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Brake Pedal Load Sensing SW
    Brake pedal load sensing switch / ON or OFF
    ON: Brake pedal depressed beyond the specified point
    OFF: Brake pedal not depressed beyond the specified point
    -

  1. Check that the brake pedal load sensing switch display observed on Techstream changes according to brake pedal operation.

    OK:
    The Techstream displays ON or OFF according to brake pedal operation.



NG
Go to step 3
OK


2.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Perform the road and braking test.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTC (C1429) is not output
    A
    DTC (C1429) is output
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH

C168971E01

NOTICE:
  1. Do not remove the brake pedal load sensing switch from the brake pedal sub-assembly.
  2. When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal sub-assembly.

  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the brake pedal load sensing switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (FSW+) - 1 (GND)
    Brake pedal load sensing switch OFF
    (Brake pedal depressed)
    950 to 1050 Ω
    2 (FSW+) - 1 (GND)
    Brake pedal load sensing switch ON
    (Brake pedal released)
    203 to 223 Ω



NG
REPLACE BRAKE PEDAL SUB-ASSEMBLY (BRAKE PEDAL LOAD SENSING SWITCH) (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)


    C168344E02
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-27 (FSW+) - A20-2 (FSW+)
    Always
    Below 1 Ω
    A24-27 (FSW+) - Body ground
    Always
    10 kΩ or higher
    A20-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)