Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected

DTC    P0305    Cylinder 5 Misfire Detected

DTC    P0306    Cylinder 6 Misfire Detected

for Preparation Click here


DESCRIPTION

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emission levels. High concentrations of HC can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increases in emissions and to limit the possibility of thermal damage, the ECM (included in the hybrid vehicle control ECU) monitors the misfire rate. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds.
If the misfire exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and sets a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinder detected
(2 trip detection logic)
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Injector
  6. Fuel pressure
  7. Mass air flow meter
  8. Engine coolant temperature sensor
  9. Compression pressure
  10. Valve clearance
  11. Valve timing
  12. PCV valve and hose
  13. PCV hose connections
  14. Intake system
  15. Hybrid vehicle control ECU
P0301
P0302
P0303
P0304
P0305
P0306
Misfiring of specific cylinder detected
(2 trip detection logic)
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Injector
  6. Fuel pressure
  7. Mass air flow meter
  8. Engine coolant temperature sensor
  9. Compression pressure
  10. Valve clearance
  11. Valve timing
  12. PCV valve and hose
  13. PCV hose connections
  14. Intake system
  15. Hybrid vehicle control ECU
When DTCs for misfiring cylinders are randomly set, but DTC P0300 is not set, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is set only when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION


A087798E04

The ECM (included in the hybrid vehicle control ECU) illuminates the MIL and sets a DTC when either one of the following conditions, which could cause emission control system performance deterioration, is detected (2 trip detection logic).
  1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs once.
  2. After the first 1000 crankshaft revolutions, an excessive misfiring rate (approximately 20 to 60 misfires per 1000 crankshaft revolutions) occurs 4 times in sequential crankshaft revolutions.
The ECM flashes the MIL and sets a DTC when either one of the following conditions, which could cause the three-way catalytic converter damage, is detected (2 trip detection logic).
  1. In every 200 crankshaft revolutions at a high engine rpm, the threshold misfiring percentage is recorded once.
  2. In every 200 crankshaft revolutions at a normal engine rpm, the threshold misfiring percentage is recorded 3 times.

MONITOR STRATEGY


Related DTCs
P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
P0305: Cylinder 5 misfire
P0306: Cylinder 6 misfire
Required Sensors/Components (Main)
Injector, Ignition coil, Spark plug
Required Sensors/Components (Related)
Crankshaft, Camshaft, Engine coolant temperature and intake air temperature sensors and Mass air flow meter
Frequency of Operation
Continuous
Duration
1000 to 4000 crankshaft revolutions: Emission related misfire
200 to 600 crankshaft revolutions: Catalyst damaging misfire
MIL Operation
2 driving cycles: Emission related misfire
MIL flashes immediately: Catalyst damaging misfire
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Misfire: 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient engine coolant temperature for closed loop)
P0327, P0328, P0332, P0333 (Knock sensor)
P0335 (Crankshaft position sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
Battery voltage
8 V or more
VVT system
No operated by scan tool
Engine RPM
750 to 5800 rpm
Both of following conditions 1 and 2 met
-
1. Engine coolant temperature
-10°C (14°F) or more
2. Either of following conditions (a) or (b) met
-
(a) Engine coolant temperature at engine start
More than -7°C (19°F)
(b) Engine coolant temperature
More than 20°C (68°F)
Fuel cut
OFF

Monitor period of emission-related misfire: 
First 1000 revolutions after engine start, or Check Mode
Crankshaft 1000 revolutions
Except above
Crankshaft 1000 revolutions x 4

Monitor period of catalyst-damaging (MIL blinks): 
All of following conditions 1, 2 and 3 met
Crankshaft 200 revolutions x 3
1. Driving cycles
1st
2. Check mode
OFF
3. Engine RPM
Less than 2600 rpm
Except above
Crankshaft 200 revolutions

TYPICAL MALFUNCTION THRESHOLDS


Monitor period of related misfire: 
Misfire rate
1% or more

Monitor period of damaging misfire (MIL blinks): 
Number of misfire per 170 revolutions
72 or more (varies with intake air amount and RPM)
Paired cylinders misfire (MIL blinks immediately)
Detected

MONITOR RESULT

Refer to CHECKING MONITOR STATUS (Click here).

WIRING DIAGRAM


A184182E02


CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG).
  3. Turn the Techstream on.
  4. Record the DTC(s) and freeze frame data.
  5. Using the Techstream, switch the ECM (included in the hybrid vehicle control ECU) from normal mode to check mode (Click here).
  6. Read the misfire counts of each cylinder (Cylinder #1 Misfire Count to Cylinder #6 Misfire Count with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.)
  7. Drive the vehicle several times with the conditions, such as engine rpm and engine load, shown in Misfire RPM and Misfire Load in the Data List.

    HINT:
    In order to store misfire DTCs, it is necessary to drive the vehicle for the period of time shown in the table below, with the Misfire RPM and Misfire Load in the Data List.

    Engine RPM
    Duration
    Idling
    5 minutes or more
    1000
    3 minutes or more
    2000
    1.5 minutes or more
    3000
    1 minute or more

  8. Check whether misfires have occurred by checking the DTCs and freeze frame data.

    HINT:
    Do not turn the power switch off until the stored DTC(s) and freeze data have been recorded. When the ECM (included in the hybrid vehicle control ECU) returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be erased.

  9. Record the DTC(s), freeze frame data and misfire counts.

INSPECTION PROCEDURE

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was Lean or Rich, and other data from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.
  4. The misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors is considered to be a possible cause of the problem:
    1. The fuel tank is low full.
    2. Improper fuel is used.
    3. The spark plugs have been contaminated.
    4. The problem is complex.
  5. After finishing repairs, check the misfire counts of the cylinders (Cylinder #1 Misfiring Count to Cylinder #6 Misfiring Count).
  6. Be sure to confirm that no misfiring cylinder DTCs are set again by conducting the confirmation driving pattern, after repairs.
  7. For 6 and 8 cylinder engines, the ECM (included in the hybrid vehicle control ECU) intentionally does not set specific misfiring cylinder DTCs at high engine RPM. If misfires occur only in high engine RPM areas, only DTC P0300 is set.
    In the event of DTC P0300 being present, perform the following operations:
    1. Clear the DTCs (Click here).
    2. Start the engine and conduct the confirmation driving pattern.
    3. Read the misfiring rates of each cylinder or DTC(s) using the Techstream.
    4. Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.
    5. After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not set.
  8. When one of Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +-20%, the air-fuel ratio may be Rich (-20% or less) or Lean (+20% or more).
  9. When the Coolant Temp in the freeze frame data is less than 75°C (167°F), misfires have occurred while warming up the engine.
  10. An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be detected.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC output)
    Proceed to
    P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306
    A
    P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 and other DTCs
    B

    HINT:
    If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305 and P0306 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the Techstream to the DLC3.

  1. Put the engine in inspection mode (Click here).

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire LOAD (engine load) values.

    HINT:
    The Misfire RPM and Misfire Load indicate the vehicle conditions under which the misfire occurred.


NEXT


3.CHECK PCV HOSE CONNECTIONS

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


4.CHECK MISFIRE COUNT (CYL #1, #2, #3, #4, #5 AND #6)
  1. Connect the Techstream to the DLC3.

  1. Put the engine in inspection mode (Click here).

  1. Turn the Techstream on.

  1. Clear the DTCs.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire / Cylinder #1 Misfire Count, #2, #3, #4, #5 and #6.

  1. Start the engine.

  1. Read each value of Cylinder #1 to #6 displayed on the tester. If no misfire counts occur in any cylinders, perform the following conditions:

    1. Shift the gear selector lever to the D position.

    2. Repeat steps (e) to (g) above.

    3. Check the Cylinder #1 Misfire Count to #6.

    4. If misfire counts are still not displayed, perform the following two steps and then check the misfire counts again.

  1. Drive the vehicle with Misfire RPM and Misfire Load noted in step 2.

  1. Read the Cylinder #1 Misfire Count to #6 or DTCs displayed on the Techstream.

    Result:

    Misfire count
    Proceed to
    1 or 2 cylinders have misfire counts
    A
    3 cylinders or more have misfire counts
    B



B
Go to step 16
A


5.CHECK SPARK PLUG


    A126880
  1. Remove the ignition coil and the spark plug of the misfiring cylinder.

  1. Measure the spark plug electrode gap.

    Standard:
    Between 1.0 mm and 1.3 mm (0.039 in. and 0.051 in.)

  1. Check the electrode for carbon deposits.
    Recommended spark plug: 
    Manufacture
    Product
    DENSO
    SK20R11
    NGK
    IFR6A11

    NOTICE:
    If the electrode gap is not as specified, replace the spark plug. Do not adjust the electrode gap.



NG
REPLACE SPARK PLUG (Click here)
OK


6.CHECK FOR SPARK
  1. Disconnect the injector connectors to prevent the engine from starting.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

  1. Remove the ignition coil from the cylinder head.

  1. Install the spark plug onto the ignition coil.

  1. Touch the spark plug tip to the cylinder head.

  1. Crank the engine for less than 2 seconds and check for spark.

    OK:
    Spark jumps across electrode gap.

  1. Install the ignition coil.

  1. Reconnect the injector connectors.



NG
Go to step 29
OK


7.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


8.CHECK HARNESS AND CONNECTOR (INJECTOR OF MISFIRING CYLINDER POWER SOURCE)


    A183068E02
  1. Disconnect the injector connectors (of the misfiring cylinder).

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    B13-2 - Body ground
    Power switch on (IG)
    11 to 14 V
    No. 2
    B14-2 - Body ground
    Power switch on (IG)
    11 to 14 V
    No. 3
    B15-2 - Body ground
    Power switch on (IG)
    11 to 14 V
    No. 4
    B16-2 - Body ground
    Power switch on (IG)
    11 to 14 V
    No. 5
    B17-2 - Body ground
    Power switch on (IG)
    11 to 14 V
    No. 6
    B18-2 - Body ground
    Power switch on (IG)
    11 to 14 V

  1. Reconnect the injector connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INJ NO. 2 FUSE - INJECTOR)
OK


9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - FUEL INJECTOR)


    A182708E01
  1. Disconnect the injector connectors.

  1. Disconnect the hybrid vehicle control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Check for open:
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    B13-1 - B1-1 (#10)
    Always
    Below 1 Ω
    No. 2
    B14-1 - B1-2 (#20)
    Always
    Below 1 Ω
    No. 3
    B15-1 - B1-3 (#30)
    Always
    Below 1 Ω
    No. 4
    B16-1 - B1-4 (#40)
    Always
    Below 1 Ω
    No. 5
    B17-1 - B1-5 (#50)
    Always
    Below 1 Ω
    No. 6
    B18-1 - B2-7 (#60)
    Always
    Below 1 Ω
    Check for short:
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    B13-1 - Body ground
    Always
    10 kΩ or higher
    No. 2
    B14-1 - Body ground
    Always
    10 kΩ or higher
    No. 3
    B15-1 - Body ground
    Always
    10 kΩ or higher
    No. 4
    B16-1 - Body ground
    Always
    10 kΩ or higher
    No. 5
    B17-1 - Body ground
    Always
    10 kΩ or higher
    No. 6
    B18-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the hybrid vehicle control ECU connectors.

  1. Reconnect the injector connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL INJECTOR - HYBRID VEHICLE CONTROL ECU)
OK


10.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the injector resistance (Click here).

  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


11.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks.

    OK:
    No leaks in intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


12.CHECK VALVE TIMING
  1. Check the valve timing (Click here).



NG
ADJUST VALVE TIMING
OK


13.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 29
OK


14.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Check the engine coolant temperature (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


15.INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here ).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

16.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks in intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


17.CHECK VALVE TIMING
  1. Check the valve timing (Click here).



NG
ADJUST VALVE TIMING
OK


18.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 29
OK


19.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Check the engine coolant temperature (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


20.INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


21.CHECK SPARK PLUG


    A126880
  1. Remove the ignition coil and the spark plug of the misfiring cylinder.

  1. Measure the spark plug electrode gap.

    Maximum gap:
    Between 1.0 mm and 1.3 mm (0.039 in. and 0.051 in.)

  1. Check the electrode for carbon deposits.
    Recommended spark plug: 
    Manufacture
    Product
    DENSO
    SK20R11
    NGK
    IFR6A11

    NOTICE:
    If the electrode gap is not as specified, replace the spark plug. Do not adjust the electrode gap.



NG
REPLACE SPARK PLUG (Click here)
OK


22.CHECK FOR SPARK
  1. Disconnect the injector connectors to prevent the engine from starting.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

  1. Remove the ignition coil from the cylinder head.

  1. Install the spark plug onto the ignition coil.

  1. Touch the spark plug tip to the cylinder head.

  1. Crank the engine for less than 2 seconds and check for spark.

    OK:
    Spark jumps across electrode gap.

  1. Install the ignition coil.

  1. Reconnect the injector connectors.



NG
Go to step 28
OK


23.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


24.CHECK HARNESS AND CONNECTOR (INJECTOR OF MISFIRING CYLINDER POWER SOURCE)


    A183068E02
  1. Disconnect the injector connectors (of the misfiring cylinder).

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    B13-2 - Body ground
    Power switch on (IG)
    11 to 14 V
    No. 2
    B14-2 - Body ground
    Power switch on (IG)
    11 to 14 V
    No. 3
    B15-2 - Body ground
    Power switch on (IG)
    11 to 14 V
    No. 4
    B16-2 - Body ground
    Power switch on (IG)
    11 to 14 V
    No. 5
    B17-2 - Body ground
    Power switch on (IG)
    11 to 14 V
    No. 6
    B18-2 - Body ground
    Power switch on (IG)
    11 to 14 V

  1. Reconnect the injector connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INJ NO. 2 FUSE - INJECTOR)
OK


25.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INJECTOR OF MISFIRING)


    A182708E01
  1. Disconnect the injector connectors.

  1. Disconnect the hybrid vehicle control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Check for open:
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    B13-1 - B1-1 (#10)
    Always
    Below 1 Ω
    No. 2
    B14-1 - B1-2 (#20)
    Always
    Below 1 Ω
    No. 3
    B15-1 - B1-3 (#30)
    Always
    Below 1 Ω
    No. 4
    B16-1 - B1-4 (#40)
    Always
    Below 1 Ω
    No. 5
    B17-1 - B1-5 (#50)
    Always
    Below 1 Ω
    No. 6
    B18-1 - B2-7 (#60)
    Always
    Below 1 Ω
    Check for short:
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    B13-1 - Body ground
    Always
    10 kΩ or higher
    No. 2
    B14-1 - Body ground
    Always
    10 kΩ or higher
    No. 3
    B15-1 - Body ground
    Always
    10 kΩ or higher
    No. 4
    B16-1 - Body ground
    Always
    10 kΩ or higher
    No. 5
    B17-1 - Body ground
    Always
    10 kΩ or higher
    No. 6
    B18-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the hybrid vehicle control ECU connectors.

  1. Reconnect the injector connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL INJECTOR - HYBRID VEHICLE CONTROL ECU)
OK


26.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the injector resistance (Click here).

  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

27.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the installed spark plug to a spark plug that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil and connect the ignition coil connector.

    2. Disconnect the injector connectors.

    3. Ground the spark plug.

    4. Check if spark occurs while the engine is being cranked.

      OK:
      Spark jumps across electrode gap.



NG
Go to step 28
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

28.CHANGE TO NORMAL IGNITION COIL AND CHECK SPARK OF MISFIRING CYLINDER


NG
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
OK

REPLACE IGNITION COIL ASSEMBLY (Click here)  

29.CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage .



NG
REPAIR OR REPLACE FUEL LINE
OK

REPLACE FUEL PUMP (Click here)