Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1202/68    Master Reservoir Level Malfunction

for Preparation Click here


DESCRIPTION

When a fluid level drop in the master cylinder reservoir is detected, the signal is input to the skid control ECU.
If the DTC for the fluid level drop is memorized, the warning will be canceled and the DTC will not be stored when the fluid level returns to normal.

DTC Code
INF Code
DTC Detection Condition
Trouble Area
C1202/68
511
Either of the following is detected:
  1. Pump motor operates for specified period when reservoir level drops.
  2. Brake operation signal is input when the reservoir level is abnormal and the power switch is on (IG).
  1. Brake fluid leak
  2. Brake fluid level
  3. Brake fluid level warning switch
  4. Brake fluid level warning switch circuit
  5. Skid control ECU
↑
512
An open in the switch signal circuit continues for 2 seconds or more.
  1. Brake fluid level warning switch
  2. Brake fluid level warning switch circuit
  3. Skid control ECU

WIRING DIAGRAM


C173831E01


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization and calibration of the linear solenoid valve (Click here).

HINT:
When releasing the parking brake, chock the wheels for safety.

1.CHECK BRAKE FLUID LEVEL


    C156531
  1. Check that the brake fluid level is sufficient.

    OK:
    Brake fluid level is sufficient.

    HINT:
    1. If the fluid level drops, check for fluid leaks, and repair as necessary.
    2. Check for brake fluid leakage (Connection between the accumulator and brake actuator, and the brake actuator and wheel cylinders).
    3. If no leak exists, add and adjust fluid and then check that the trouble code is not output again.



    C176022
  1. Check that there are no leaks from the connections between the brake booster pump and brake actuator.

    HINT:
    As a visual check is very difficult, perform the check with the following procedure.

    1. Bleed air from the brake actuator (Click here).

    2. Connect the Techstream to the DLC3.

    3. Turn the power switch on (IG).

    4. Select the Data List mode on the Techstream (Click here).

      ABS / VSC / TRAC: 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Accumulator Sensor
      Accumulator pressure sensor / min.: 0 V, max.: 5 V
      Specified value: 3.3 to 4.7 V
      -

    5. Wait a few minutes without operating the brake pedal.

    6. Check that the output value of the accumulator pressure sensor does not decrease and that the pump motor is not activated due to a decrease in accumulator pressure.

      OK:
      Accumulator pressure does not decrease and the pump motor is not activated due to a decrease in accumulator pressure.



NG
CHECK AND REPAIR BRAKE FLUID LEAKAGE OR ADD FLUID
OK


2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
C156521E01
  1. Turn the power switch off.

  1. Remove the reservoir filler cap and strainer.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    A float is located inside the reservoir. Its position changes according to the level of brake fluid.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Brake fluid level warning Switch OFF (Float up)
    1.9 to 2.1 kΩ
    1 - 2
    Brake fluid level warning Switch ON (Float down)
    Below 1 Ω

    HINT:
    If there are no problems after completing the preceding inspection, adjust the brake fluid to the MAX level with the power switch on (IG).



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)
C173832E01
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A45-6 (LBL) - A21-2
    Always
    Below 1 Ω
    A45-6 (LBL) - Body ground
    Always
    10 kΩ or higher
    A21-1 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT SKID CONTROL ECU (SWITCH INPUT)


    C173833E01
  1. Reconnect the skid control ECU connector and the brake fluid level warning switch connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A45-6 (LBL) - Body ground
    Power switch on (IG)
    8 to 14 V



NG
REPLACE SKID CONTROL ECU (Click here)
OK


5.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (IG).

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTC (C1202/68) is not output
    A
    DTC (C1202/68) is output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE SKID CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)