Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1247/47    Stroke Sensor Malfunction

DTC    C1346/71    Stroke Sensor Zero Point Learning Malfunction (Test Mode DTC)

DTC    C1392/48    Stroke Sensor Zero Point Calibration Undone

for Preparation Click here


DESCRIPTION

The stroke sensor inputs the pedal stroke into the skid control ECU.
DTC C1346/71 will be deleted when the brake pedal stroke sensor sends a stroke sensor signal or when Test Mode ends. DTC C1346/71 is output only in Test Mode.

DTC Code
INF Code
DTC Detection Condition
Trouble Area
C1247/47
171
Sensor power source voltage (VCSK) is 3.6 V or less or 4.95 V or more for at least 1.2 seconds.
  1. Brake pedal stroke sensor
  2. Brake pedal stroke sensor power supply
  3. Skid control ECU
↑
172
Ratio of sensor output voltage 1 (SKS1) to sensor power source voltage (VCSK) is less than 3% or 97% or more for at least 1.2 seconds.
  1. Brake pedal stroke sensor
  2. Brake pedal stroke sensor circuit
↑
173
Ratio of sensor output voltage 2 (SKS2) to sensor power source voltage (VCSK) is less than 3% or 97% or more for at least 1.2 seconds.
↑
↑
174
Sensor output 1 (SKS1) calculation value becomes 20 mm or more for at least 1.2 seconds at an interval of 0.006 seconds (changes due to interference).
↑
↑
175
Sensor output 2 (SKS2) calculation value becomes 20 mm or more for at least 1.2 seconds at an interval of 0.006 seconds (changes due to interference).
↑
↑
176
Zero point stored value (ratio to power source voltage) of sensor output 1 (SKS1) is 0.46 or more or 0.03 or less.
  1. Brake pedal stroke sensor
  2. Brake pedal stroke sensor circuit
  3. Sensor installation
↑
177
Zero point stored value (ratio to power source voltage) of sensor output 2 (SKS2) is 0.46 or more or 0.03 or less.
↑
↑
179
Either of the following is detected:
  1. Sum of SKS1/VCSK and SKS2/VCSK is 1.155 or more or 0.845 or less for at least 1 second.
  2. Difference between sensor output 1 (SKS1) and sensor output 2 (SKS2) is excessively large for at least 0.2 seconds.
  1. Brake pedal stroke sensor
  2. Brake pedal stroke sensor circuit
↑
180
Either of the following is detected:
  1. Difference between zero point output value and stored value is 0.5 or more for at least 0.05 seconds.
  2. Short between SKS1 and SKS2 output line.
  1. Brake pedal stroke sensor
  2. Brake pedal stroke sensor circuit
  3. Skid control ECU
C1392/48
178
Zero point calibration of stroke sensor is unfinished.
  1. Brake pedal stroke sensor zero point calibration incomplete (Initialization and calibration of linear solenoid valve incomplete)
  2. Skid control ECU
C1346/71
-
Detected only during Test Mode.
Brake pedal stroke sensor

WIRING DIAGRAM


C173865E01


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU or brake pedal stroke sensor, perform initialization and calibration of the linear solenoid valve (Click here).

HINT:
Check the condition of each related circuit connector before troubleshooting (Click here).

1.CHECK BRAKE PEDAL
  1. Check that the brake pedal and the brake pedal stroke sensor are properly installed and that the pedal can be operated normally.

  1. Check and adjust the brake pedal height (Click here).

  1. Adjust the brake pedal stroke sensor (Click here).


NEXT


2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL STROKE SENSOR)


    C173866E01
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connector and the brake pedal stroke sensor connector.

  1. Check both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A47-6 (VCSK) - A50-3 (VCSK)
    Always
    Below 1 Ω
    A47-6 (VCSK) - Body ground
    Always
    10 kΩ or higher
    A47-8 (SKG) - A50-1 (SKG)
    Always
    Below 1 Ω
    A47-8 (SKG) - Body ground
    Always
    10 kΩ or higher
    A47-20 (SKS1) - A50-4 (SKS1)
    Always
    Below 1 Ω
    A47-20 (SKS1) - Body ground
    Always
    10 kΩ or higher
    A47-22 (SKS2) - A50-2 (SKS2)
    Always
    Below 1 Ω
    A47-22 (SKS2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE
  1. Reconnect the skid control ECU connector and the brake pedal stroke sensor connector.

  1. Perform initialization and calibration of the linear solenoid valve (Click here).


NEXT


4.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Perform a road test.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C1247/47 and/or C1392/48) are output
    A
    DTCs (C1247/47 and C1392/48) are not output
    B



B
END
A


5.INSPECT SKID CONTROL ECU (SENSOR INPUT)


    C173833E04
  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A47-6 (VCSK) - Body ground
    Power switch on (IG)
    3.75 to 4.95 V

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A47-8 (SKG) - Body ground
    Always
    Below 1 Ω



NG
REPLACE SKID CONTROL ECU (Click here)
OK


6.READ VALUE USING TECHSTREAM (BRAKE PEDAL STROKE SENSOR)
  1. Connect the pedal effort gauge (Click here).

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the Data List mode on the Techstream (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stroke Sensor
    Stroke sensor /
    min.: 0 V, max.: 5 V
    When brake pedal is released:
    0.7 to 1.3 V
    -
    Stroke Sensor2
    Stroke sensor 2 /
    min.: 0 V, max.: 5 V
    When brake pedal is released:
    3.7 to 4.3 V
    -

  1. When depressing the brake pedal with the amount of force listed in the table below, check that the output value displayed on the Techstream is within the standard voltage.

    HINT:
    The brake pedal must be depressed gradually.


    Standard voltage:

    Brake Effort N (kgf, lbf)
    Stroke Sensor
    (Data List Display)
    Stroke Sensor2
    (Data List Display)
    50 (5.1, 11.2)
    1.15 to 1.55 V
    3.40 to 3.80 V
    100 (10.2, 22.4)
    1.30 to 1.70 V
    3.25 to 3.65 V
    150 (15.3, 34.0)
    1.40 to 1.80 V
    3.15 to 3.55 V
    200 (20.4, 45.0)
    1.50 to 1.90 V
    3.05 to 3.45 V



NG
REPLACE BRAKE PEDAL STROKE SENSOR (Click here)
OK


7.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Perform a road test.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C1247/47 and C1392/48) are not output
    A
    DTCs (C1247/47 and/or C1392/48) are output
    B



B
REPLACE SKID CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)