Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C0371/71    Yaw Rate Sensor (Test Mode DTC)

DTC    C1234/34    Yaw Rate Sensor Malfunction

DTC    C1243/43    Acceleration Sensor Stuck Malfunction

DTC    C1244/44    Open or Short in Acceleration Sensor Circuit

DTC    C1245/45    Acceleration Sensor Output Malfunction

DTC    C1279/79    Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)

DTC    C1381/97    Acceleration Sensor Power Supply Voltage Malfunction

for Preparation Click here


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system.
The yaw rate sensor has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).
If there are any problems in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, DTCs U0123/62 (malfunction in CAN communication with the yaw rate sensor) and U0124/95 (malfunction in CAN communication with the acceleration sensor) are output.
These DTCs are also output when calibration has not been completed.
DTCs C0371/71 and C1279/79 will be deleted when the yaw rate and acceleration sensor sends a yaw rate and/or acceleration signal or when Test Mode ends. DTCs C0371/71 and C1279/79 are output only in Test Mode.

DTC Code
INF Code
DTC Detection Condition
Trouble Area
C1234/34
331
332
333
334
335
337
When ECU IG1 terminal voltage is between 9.5 and 17.4 V, the sensor malfunction signal is received from the yaw rate sensor.
Yaw rate and acceleration sensor
C1243/43
317
While the vehicle speed changes from over 30 km/h (18 mph) to 0 km/h (0 mph), the values of GL1 and GL2 do not change 16 times or more.
Yaw rate and acceleration sensor
C1244/44
314
Either of the following is detected:
  1. A malfunction signal is received from the acceleration sensor.
  2. After the difference between GL1 and GL2 becomes 0.6 G or more with the vehicle stationary, the difference remains greater than 0.4 G for 60 seconds or more.
  1. Yaw rate and acceleration sensor
  2. Sensor installation
C1245/45
313
At a vehicle speed of 30 km/h (18 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed sensor exceeds 0.35 G for 60 seconds or more.
  1. Yaw rate and acceleration sensor
  2. Sensor installation
C1381/97
315
At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is received for 10 seconds or more.
  1. Yaw rate and acceleration sensor
  2. Yaw rate and acceleration sensor power source circuit
  3. Skid control ECU
C0371/71
-
Detected only during Test Mode.
Yaw rate and acceleration sensor
C1279/79
-
Detected only during Test Mode.
  1. Yaw rate and acceleration sensor
  2. Sensor installation

WIRING DIAGRAM


C146554E06


INSPECTION PROCEDURE

NOTICE:
When replacing the yaw rate and acceleration sensor, perform zero point calibration (Click here).

HINT:
When U0123/62 and/or U0124/95 is output together with C1234/34, C1243/43, C1244/44, C1245/45, and/or C1381/97, inspect and repair the trouble areas indicated by U0123/62 and/or U0124/95 first (Click here).

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (READY).

  1. Drive the vehicle at a speed of 30 km/h (18 mph) or more, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.

  1. Turn the power switch on (IG) again and check that no CAN communication system DTC is output (Click here).

  1. Check if DTC C1210/36 (zero point calibration of yaw rate sensor undone) or C1336/98 (zero point calibration of acceleration sensor undone) is output (Click here).

    Result:

    Result
    Proceed to
    DTCs (C1210/36, C1336/98 and CAN communication system DTC) are not output
    A
    CAN communication system DTC is output
    B
    DTCs (C1210/36 and/or C1336/98) are output
    C



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)

C
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)
A


2.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION
  1. Turn the power switch off.

  1. Check that the yaw rate and acceleration sensor has been installed properly (Click here).

    OK:
    The sensor is tightened to the specified torque.
    The sensor is not tilted.



NG
INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY (Click here)
OK


3.INSPECT YAW RATE AND ACCELERATION SENSOR (IG TERMINAL)
C156491E11
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the yaw rate and acceleration sensor connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O6-4 (IG) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)
OK


4.INSPECT YAW RATE AND ACCELERATION SENSOR (GND TERMINAL)


    C156491E12
  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O6-1 (GND) - Body ground
    Always
    Below 1 Ω

    NOTICE:
    Check the yaw rate and acceleration sensor signal after replacement (Click here).

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK

REPLACE YAW RATE AND ACCELERATION SENSOR (Click here)