Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL OIL SEAL › 2013.12–2016.11
RM3160E _52 Drivetrain _019725 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0107327 DIFFERENTIAL OIL SEAL A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL  REPLACEMENT  


PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 53876A 2.SEPARATE FRONT FENDER LINER LH

Hide 53737B 3.REMOVE FRONT FENDER APRON SEAL LH

Hide 4.DRAIN AUTOMATIC TRANSAXLE FLUID

a.
C201682

Remove the refill plug and gasket from the automatic transaxle assembly.


b.
C239660

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle oil pan sub-assembly.


c.
C201684C20
1.208,2.677 0.833,2.677 false 0.604,3.927 0.417,3.927 0.417,3.927 0.708,3.125 false 1.208,3.219 0.833,3.219 false 1.219,2.594 1.375,2.76 0.156,0.167 10 false *1 1.219,3.135 1.385,3.302 0.167,0.167 10 false *a 0.656,3.844 0.833,4.031 0.177,0.188 10 false *b
*1 No. 1 Transmission Oil Filler Tube
*a Hexagon Socket Wrench
*b Overflow Plug Hole


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.


d.

Drain the automatic transaxle fluid from the automatic transaxle assembly.


e.
C201684C21
1.208,2.677 0.833,2.677 false 0.604,3.927 0.417,3.927 0.417,3.927 0.708,3.125 false 1.208,3.219 0.833,3.219 false 1.219,2.594 1.375,2.76 0.156,0.167 10 false *1 1.219,3.135 1.385,3.302 0.167,0.167 10 false *a 0.656,3.844 0.833,4.031 0.177,0.188 10 false *b
*1 No. 1 Transmission Oil Filler Tube
*a Hexagon Socket Wrench
*b Overflow Plug Hole


Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


f.
C239660

Using a 6 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the automatic transaxle oil pan sub-assembly.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.



g.
C201682

Temporarily install the gasket and refill plug to the automatic transaxle assembly.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



Hide 12321A 6.REMOVE REAR ENGINE MOUNTING BRACKET

Hide 43420H 7.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C301305N01
0.792,0.979 0.688,0.771 0.688,0.771 0.563,0.771 false 0.833,2.438 0.76,2.156 0.76,2.156 0.635,2.156 false 0.271,0.688 0.708,0.969 0.438,0.281 10 false SST 0.323,2.083 0.76,2.365 0.438,0.281 10 false SST

Using SST, remove the front drive shaft oil seal LH from the automatic transaxle assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the transaxle case sub-assembly.



Hide 43410M 8.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C301306N01
0.979,0.625 0.906,0.302 0.906,0.302 0.76,0.302 false 1.802,2.375 1.729,2.177 1.729,2.177 1.583,2.177 false 0.406,0.219 0.854,0.51 0.448,0.292 10 false SST 1.26,2.094 1.708,2.385 0.448,0.292 10 false SST

Using SST, remove the front drive shaft oil seal RH from the automatic transaxle assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the transaxle housing.



Hide 43420H 9.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C274794N01
1.198,1.813 1.823,2.677 1.823,2.677 1.448,1.906 true 1.979,1.313 1.385,0.302 1.385,0.302 2.104,0.896 true 1.75,2.719 2.208,2.917 0.458,0.198 10 SST 1.083,0.208 1.542,0.406 0.458,0.198 10 SST

Using SST and a hammer, install a new front drive shaft oil seal LH to the automatic transaxle assembly.

SST
09316-10010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal LH is installed in the correct direction.

·

Do not damage the front drive shaft oil seal LH lip.




b.

Coat the lip of the front drive shaft oil seal LH with MP grease.


Hide 43410M 10.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C188729N03
1.563,2.073 1.563,2.646 false 2.146,0.771 2.146,1.146 false 1.396,2.667 1.719,2.823 0.323,0.156 10 false SST 1.969,1.146 2.292,1.302 0.323,0.156 10 false SST

Using SST and a hammer, install a new front drive shaft oil seal RH to the automatic transaxle assembly.

SST
09316-60011  (09316-00011)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal RH is installed in the correct direction.

·

Do not damage the front drive shaft oil seal RH lip.




b.

Coat the lip of the front drive shaft oil seal RH with MP grease.


Hide 12321A 11.INSTALL REAR ENGINE MOUNTING BRACKET

Hide 53737B 14.INSTALL FRONT FENDER APRON SEAL LH

Hide 53876A 15.INSTALL FRONT FENDER LINER LH

Hide 51441 16.INSTALL NO. 1 ENGINE UNDER COVER