Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER(for RHD) › 2013.12–2016.11
RM3160E _54 Brake _019693 BRAKE SYSTEM (OTHER) _0108091 BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD)  INSTALLATION  


PROCEDURE

Hide 44785 1.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster assembly.


Hide 44610 2.INSTALL BRAKE BOOSTER ASSEMBLY

a.

Temporarily install the brake booster assembly to the vehicle body.


b.

Temporarily install the lock nut and brake master cylinder push rod clevis to the brake booster assembly.

NOTICE:

Fully tighten the lock nut when adjusting the brake pedal height.



c.

Install the 4 nuts to secure the brake booster assembly.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 47264A 3.INSTALL PUSH ROD PIN

Hide 47101A 4.INSTALL BRAKE PEDAL RETURN SPRING

Hide 11201 5.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11322F 7.INSTALL NO. 2 TIMING GEAR COVER

Hide 23292D 8.INSTALL FUEL HOSE PROTECTOR

Hide 19500 9.INSTALL IGNITION COIL ASSEMBLY

a.

Install the 3 ignition coil assemblies with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82121 10.INSTALL ENGINE WIRE

a.

Install the engine wire to the cylinder head cover sub-assembly with the bolt.


b.
C294918C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


Install the bolt, engage the 4 clamps and connect the 10 connectors.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 44781 11.INSTALL HOSE BRACKET

a.

Install the hose bracket with the bolt.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


b.

Engage the clamp to install the engine wire.


Hide 12262 12.CONNECT NO. 2 VENTILATION HOSE

a.

Connect the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.


Hide 17125 13.INSTALL NO. 1 SURGE TANK STAY

Hide 22267A 14.INSTALL THROTTLE BODY BRACKET

Hide 17190 15.INSTALL INTAKE AIR SURGE TANK ASSEMBLY

Hide 22271 16.INSTALL THROTTLE BODY GASKET

Hide 22030 17.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 18.INSTALL BRAKE LINE

a.
C294915C01
1.271,0.219 1.938,0.5 1.938,0.5 1.938,1.125 true 1.563,1.469 1.563,1.917 true 1.104,0.469 1.448,0.635 1.448,0.635 1.448,1.083 true 1.5,1.948 1.813,2.104 0.313,0.156 10 false *1 1.104,0.115 1.417,0.271 0.313,0.156 10 false *2 0.927,0.375 1.24,0.531 0.313,0.156 10 false *3
*1 Front No. 6 Brake Tube
*2 Front No. 7 Brake Tube
*3 Front No. 8 Brake Tube


Install the front No. 6 brake tube and front No. 7 brake tube, and engage the 3 clamps to secure the 3 brake lines.

NOTICE:
·

Do not damage the 3 clamps.

·

Do not kink or damage the brake lines.



HINT:

Install the front No. 6 brake tube and front No. 7 brake tube while avoiding the front No. 8 brake tube.



b.
C294914N01
1.479,0.833 1.635,1.031 0.156,0.198 10 true A 1.531,1.49 1.688,1.688 0.156,0.198 10 true A 1.958,1.281 2.115,1.479 0.156,0.198 10 true B

Engage the clamp to secure the 3 brake lines.

NOTICE:
·

Do not damage the clamp.

·

Do not kink or damage the brake lines.




c.

Using a union nut wrench, connect the 3 brake lines to the brake actuator assembly.

Torque:
Brake Line (A) : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)
Brake Line (B) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




Hide 88704 19.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction hose sub-assembly.


b.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the suction hose sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the 2 O-rings to the suction hose sub-assembly


d.
C294913

Connect the suction hose sub-assembly to the No. 1 air conditioning accessory assembly.

NOTICE:

Do not deform the refrigerant lines.



e.
C294911

Install the piping clamp to the suction hose sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT LINE>INSTALLATION


Hide 20.INSTALL AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape from the air conditioner tube and accessory assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioner tube and accessory assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the air conditioner tube and accessory assembly.


d.

Insert the air conditioner tube and accessory assembly to the air conditioning unit assembly.


e.

Install the air conditioner tube and accessory assembly with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Do not deform the refrigerant lines.



f.

Install the air conditioner tube and accessory assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Do not deform the refrigerant lines.



g.

Engage the clamp to install the air conditioner tube and accessory assembly to the brake actuator assembly.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




h.

Engage the clamp to install the air conditioner tube and accessory assembly.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




Hide 88704 21.INSTALL SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction hose sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction hose sub-assembly.


d.

Insert the suction hose sub-assembly to the air conditioning unit assembly.


e.
C294909

Rotate the hook connector as shown in the illustration.


f.

Insert the tube joint into the fitting hole securely and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


g.
C292899

Install the suction hose sub-assembly to the piping clamp.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




h.

Engage the claw to lock the piping clamp.


i.

Install the suction hose sub-assembly to the suction hose clamp, and engage the claw to secure it.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




j.

Engage the clamp to install the suction hose sub-assembly to the brake actuator assembly.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




k.

Engage the clamp to install the suction hose sub-assembly.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




Hide 12313 22.INSTALL ENGINE MOVING CONTROL ROD BRACKET

Hide 12327A 23.INSTALL NO. 2 ENGINE MOUNTING STAY RH

Hide 44773F 24.CONNECT UNION TO CHECK VALVE HOSE

a.

Connect the union to check valve hose to the brake booster assembly, and slide the clip to secure it.


Hide 47233 25.INSTALL RESERVOIR BRACKET

a.

Install the reservoir bracket with the 2 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Engage the clamp to install the engine room main wire.


Hide 47220D 26.INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

a.
C294904C01
0.76,3.698 0.76,4.104 true 0.458,3.698 0.458,4.115 true 0.708,4.115 1.021,4.271 0.313,0.156 10 false *1 0.385,4.125 0.698,4.281 0.313,0.156 10 false *2
*1 Brake Master Cylinder Reservoir Assembly
*2 Reservoir Bracket


Move the brake master cylinder reservoir assembly as shown in the illustration to engage the 2 claws.


b.

Connect the reservoir level switch connector and install the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 82111 27.INSTALL ENGINE ROOM MAIN WIRE

a.
C294900C01
2.229,2.438 2.385,2.844 true 2.323,2.844 2.542,3.042 0.219,0.198 10 true *a
*a Wire Harness Protector


Engage the 5 clamps to install the engine room main wire.


b.

Engage the clamp to install the wire harness protector.


c.

Install the bolt to secure the wire harness protector.


Hide 17801 28.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17705 29.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 30.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 31.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY WITH WAY

Hide 33.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 36.INSPECT FOR COOLANT LEAK

Hide 37.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR TANK

Hide 38.INSPECT AND ADJUST BRAKE PEDAL

Hide 11209 39.INSTALL V-BANK COVER SUB-ASSEMBLY

Hide 40.INSTALL FRONT WHEEL RH

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)