Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › ENGINE › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019663 2GR-FE ENGINE MECHANICAL _0109576 ENGINE G

2GR-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 17801 5.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


b.

Visually check that the air cleaner filter element sub-assembly is not excessively damaged or oily.

HINT:
·

If necessary, replace the air cleaner filter element sub-assembly.

·

If there is any dirt or clogs in the air cleaner filter element sub-assembly, clean it with compressed air.

·

If any dirt or clogs remain even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.




c.

Install the air cleaner filter element sub-assembly.


Hide 16620 6.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY


b.

Check that nothing is caught in the V-ribbed belt tensioner assembly by turning it clockwise and counterclockwise.

HINT:

If a malfunction exists, replace the V-ribbed belt tensioner assembly.




Hide 7.INSPECT VALVE LASH ADJUSTER ASSEMBLY NOISE

a.

Rev up the engine several times. Check that the engine does not emit unusual noises.


b.

If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the inspection.

HINT:

If any defects or problems are found during the inspection, perform valve lash adjuster assembly inspection.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION



Hide 8.INSPECT IGNITION TIMING

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine / Data List / IGN Advance.

Powertrain > Engine > Data List
Tester Display
IGN Advance
50003 234 29
Standard Ignition Timing:

9.5 to 24.5° BTDC at idle


NOTICE:
·

Check the ignition timing with the cooling fans off.

·

Turn off all the electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.




v.

Check that the ignition timing advances immediately when the engine speed is increased.


vi.

Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1 / ON.

Powertrain > Engine > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
IGN Advance
50004 234 13 29

vii.

Monitor IGN Advance.


viii.

Perform the Active Test.

Standard Ignition Timing:

8 to 12° BTDC at idle


NOTICE:
·

Check the ignition timing with the cooling fans off.

·

Turn off all the electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.





c.

When not using the GTS:

i.
A206183C65
1.771,1.479 2.083,1.917 2.083,1.917 2.167,1.917 true 1.604,0.927 1.333,0.396 1.333,0.396 1.219,0.396 true 0.073,0.083 0.438,0.385 0.365,0.302 10 false *a 2.208,1.833 2.521,2.031 0.313,0.198 10 false TC 1,0.313 1.396,0.552 0.396,0.24 10 false CG
*a DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:
·

Confirm the terminal numbers before connecting them. Connecting the wrong terminals may damage electrical components.

·

Check the ignition timing with the cooling fans off.

·

Turn off all the electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.




ii.

Remove the V-bank cover sub-assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL


iii.

Connect the clip of the timing light to the ignition coil wire for the No. 1 cylinder.

NOTICE:

Use a timing light that detects primary signals.



iv.

Start the engine and run it at idle.


v.

Check the ignition timing at idle.

Standard Ignition Timing:

8 to 12° BTDC at idle


NOTICE:
·

Check the ignition timing with the cooling fans off.

·

Turn off all the electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.



HINT:

Run the engine at 1000 to 1300 rpm for 5 seconds, and then check that the engine speed returns to engine idle speed.



vi.

Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.


vii.

Check the ignition timing at idle.

Standard Ignition Timing:

9.5 to 24.5° BTDC at idle


NOTICE:
·

Check the ignition timing with the cooling fans off.

·

Turn off all the electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.




viii.

Confirm that the ignition timing advances immediately when the engine speed is increased.


ix.

Disconnect the clip of the timing light from the ignition coil wire for the No. 1 cylinder.


x.

Install the V-bank cover sub-assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION



Hide 9.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 234 9

v.

Read the value displayed on the tester.

Standard Idle Speed:

600 to 700 rpm


NOTICE:
·

Check the idle speed with the cooling fans off.

·

Turn off all the electrical systems and the A/C.

·

When checking the idle speed, the transaxle should be in neutral or park.





c.

When not using the GTS:

i.
A206183C66
1.042,1.906 1.042,1.479 false 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.938,1.938 1.396,2.135 0.458,0.198 10 false TAC
*a DLC3


Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.

SST
09843-18030  

NOTICE:

Be sure to connect the tachometer probe to the correct terminal. Connecting the wrong terminals may damage electrical components.



ii.

Start the engine and run it at idle.


iii.

Check the idle speed.

Standard Idle Speed:

600 to 700 rpm


NOTICE:
·

Check the idle speed with the cooling fans off.

·

Turn off all the electrical systems and the A/C.

·

When checking the idle speed, the transaxle should be in neutral or park.




iv.

Turn the engine switch off.


v.

Disconnect the tachometer probe from terminal 9 (TAC) of the DLC3.



Hide 10.INSPECT COMPRESSION

NOTICE:

Keep the intake manifold and spark plug holes free of foreign matter when measuring the compression pressure.


a.

Warm up and stop the engine.




d.
A129621

Check the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

While cranking the engine, measure the compression pressure.

Standard Compression Pressure:

1300 kPa (13.3 kgf/cm2, 189 psi)


Minimum Compression Pressure:

1000 kPa (10.2 kgf/cm2, 145 psi)


NOTICE:
·

Always use a fully charged battery to obtain an engine speed of 250 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression pressure as quickly as possible.




iii.

If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole then inspect the cylinder compression pressure again.

HINT:
·

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leaks in the cylinder head gasket.






f.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

After the inspection, clear the DTCs, check for DTCs again and make sure the normal system code is output.



Hide 11.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with regulations.


a.

Start the engine.


b.

Run the engine speed at 2500 rpm for approximately 180 seconds.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idle.


d.

Immediately check the CO/HC concentration during idle and when the engine is running at 2500 rpm.

HINT:

When performing the 2 mode (with the engine idling/running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.

If the CO/HC concentration does not comply with the regulations, perform troubleshooting in the order given below.



ii.

See the following table for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problem Cause
Normal High Rough idle
1.

Faulty ignition:

-

Incorrect valve timing

-

Fouled, shorted or improperly gapped spark plugs


2.

Incorrect valve clearance (valve lash adjuster assembly)

3.

Leaks in intake or exhaust valves

4.

Leaks in cylinders


Low High Rough idle
(Fluctuating HC reading)
1.

Vacuum leaks:

-

PCV hoses

-

Intake manifold

-

Throttle with motor body assembly

-

Brake booster line


2.

Lean mixture causing misfire


High High Rough idle
(Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve

3.

Faulty SFI system:

-

Fuel pressure regulator assembly

-

Engine coolant temperature sensor

-

Mass air flow meter sub-assembly

-

ECM

-

Fuel injector assemblies

-

Throttle position sensor (built into throttle with motor body assembly)