82125J
1.INSTALL TRANSMISSION WIRE
Coat the O-ring of the transmission wire with Toyota Genuine ATF WS.
Install the transmission wire to the automatic transaxle case sub-assembly with the bolt.
Connect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.
Install the temperature sensor to the transmission valve body assembly with the bolt and temperature sensor clamp.
| *a | Transmission Wire (Temperature Sensor Wire) |
| *b | Transmission Revolution Sensor (NC) Wire |
To prevent it from being pinched between the transmission valve body assembly and the transmission case side cover, pass the transmission revolution sensor (NC) wire under the transmission wire (temperature sensor wire) as shown in the illustration.
Connect the 9 solenoid valve connectors.
|
Do not let transmission wire protrude into this area. |
To prevent it from being pinched between the transmission valve body assembly and the transmission case side cover, do not let the transmission wire ride up over the area shown in the illustration.
To prevent it from being pinched between the transmission case side cover and the automatic transaxle case sub-assembly, do not let the transmission wire protrude toward the transmission case side cover installation surface.
Engage the clamp, and connect the transmission wire to the solenoid lock plate.
35151F
2.INSTALL TRANSMISSION CASE SIDE COVER (for TMC Made)
| *a | TMC Made |
| *b | AW Made |
TMC (TOYOTA) Made and AW (AISIN AW) Made components can be identified by the differing locations where the serial number is stamped.
|
Area to be cleaned |
Clean the transmission case side cover installation surface of the automatic transaxle case sub-assembly.
Completely remove any oil or grease from the contact surfaces of the automatic transaxle case sub-assembly.
Clean the 3 bolt holes shown in the illustration.
| *a | Adhesive |
Apply adhesive to 2 or 3 threads on the end of the bolt (A) and 2 bolts (D).
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Make sure to install the bolts immediately after applying adhesive to prevent foreign matter from attaching to them.
The bolt (A) and 2 bolts (D) are in the locations shown in the following step.
Temporarily install a new transmission case side cover to the automatic transaxle case sub-assembly with the 2 bolts ((A) and (B)).
Bolt (A) is an adhesive-coated bolt.
To avoid damaging the gasket, prevent it from contacting the surrounding area during installation procedures.
Temporarily install the 6 bolts (C) and 2 bolts (D).
Bolt (D) is an adhesive-coated bolt.
Operate the engine support bridge and the jack to lower the engine and automatic transaxle assembly.
| *a | Torque Wrench Fulcrum Length |
Fully tighten the 10 bolts in the order shown in the illustration.
If a socket wrench will not fit, use a union nut wrench.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) Bolt (A) and Bolt(D):
5.7 N*m (58 kgf*cm, 50 in.*lbf)
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) Bolt (B) and Bolt (C):
6.2 N*m (63 kgf*cm, 55 in.*lbf)
Tighten the engine mounting insulator LH with the nut.
Tighten the front engine mounting insulator assembly with the bolt.
Connect the transmission wire connector.
35151F
3.INSTALL TRANSMISSION CASE SIDE COVER (for AISIN AW Made)
| *a | TMC Made |
| *b | AW Made |
TMC (TOYOTA) Made and AW (AISIN AW) Made components can be identified by the differing locations where the serial number is stamped.
|
Area to be cleaned |
Clean the transmission case side cover installation surface of the automatic transaxle case sub-assembly.
Completely remove any oil or grease from the contact surfaces of the automatic transaxle case sub-assembly.
Temporarily install a new transmission case side cover to the automatic transaxle case sub-assembly with the 2 bolts (A and B).
To avoid damaging the gasket, prevent it from contacting the surrounding area during installation procedures.
Temporarily install the 8 bolts (C).
Operate the engine support bridge and the jack to lower the engine and automatic transaxle assembly.
| *a | Torque Wrench Fulcrum Length |
Fully tighten the 10 bolts in the order shown in the illustration.
If a socket wrench will not fit, use a union nut wrench.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
6.2 N*m (63 kgf*cm, 55 in.*lbf)
Tighten the engine mounting insulator LH with the nut.
Tighten the front engine mounting insulator assembly with the bolt.
Connect the transmission wire connector.
32901C
4.CONNECT OIL COOLER UNION SUB-ASSEMBLY
| *1 | Oil Cooler Union Bolt |
| *2 | Gasket |
Pass the oil cooler union sub-assembly through 2 new gaskets and temporarily install it to the automatic transaxle case sub-assembly.
Temporarily install the oil cooler union sub-assembly bracket portion to the automatic transaxle case sub-assembly with the bolt.
Fully tighten the oil cooler union bolt.
Fully tighten the bolt.
32942
5.CONNECT OUTLET NO. 1 OIL COOLER HOSE
32971
6.CONNECT TRANSMISSION OIL THERMOSTAT
Connect the transmission oil thermostat to the front frame assembly with the 2 bolts.
7.REMOVE ENGINE SUPPORT BRIDGE
8.REMOVE ENGINE HANGER
9.INSTALL WIRE HARNESS CLAMP BRACKET
17176
10.INSTALL AIR SURGE TANK TO INTAKE MANIFOLD GASKET
17190
11.INSTALL INTAKE AIR SURGE TANK ASSEMBLY
25860
12.CONNECT PURGE VALVE (PURGE VSV)
22030
13.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
12261
14.CONNECT VENTILATION HOSE
28800
15.INSTALL BATTERY
17700
16.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
17750A
17.INSTALL INLET AIR CLEANER ASSEMBLY
53295E
18.INSTALL COOL AIR INTAKE DUCT SEAL
53298E
19.INSTALL RADIATOR SIDE SEAL RH
53299D
20.INSTALL RADIATOR SIDE DEFLECTOR SEAL LH
55701J
21.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
22.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
23.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
24.ADD AUTOMATIC TRANSAXLE FLUID
53737B
25.INSTALL FRONT FENDER APRON SEAL LH
53736
26.INSTALL FRONT FENDER APRON SEAL RH
53876A
27.INSTALL FRONT FENDER LINER LH
53875A
28.INSTALL FRONT FENDER LINER RH
51441
29.INSTALL NO. 1 ENGINE UNDER COVER
11209
30.INSTALL V-BANK COVER SUB-ASSEMBLY
31.INSTALL FRONT WHEELS