Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0299070 SFI SYSTEM J

2GR-FKS ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646E29
1.229,0.823 3.042,1.125 1.813,0.302 10 false from EFI-MAIN Fuse 1.219,1.177 2.979,1.531 1.76,0.354 10 false from EFI-MAIN Relay 0.135,1.969 2.625,2.469 2.49,0.5 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.135,2.646 2.563,3.031 2.427,0.385 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.969,3.094 5.313,3.406 0.344,0.313 10 false ECM 2.885,0.677 3.563,1 0.677,0.323 10 false BATT 2.823,1.042 3.49,1.292 0.667,0.25 10 false +B, +B2 3.063,2.021 3.427,2.25 0.365,0.229 10 false VC 4.396,0.875 6.188,1.229 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.76 6.354,2.115 0.99,0.354 10 false Microprocessor 4.073,2.844 4.333,3.063 0.26,0.219 10 false R

When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

·

For the circuit diagram of the ECM power source refer to the ECM power source circuit.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit

·

VC Output Circuit

A358794E05
0.521,0.479 0.979,0.677 0.458,0.198 10 false C41 0.51,2.052 0.969,2.25 0.458,0.198 10 false Z5 0.51,3.313 0.969,3.51 0.458,0.198 10 false C35 0.531,4.625 0.99,4.823 0.458,0.198 10 false C54 0.521,5.917 0.979,6.115 0.458,0.198 10 false C36 0.531,7.24 0.99,7.438 0.458,0.198 10 false C53 2.844,0.385 3.302,0.583 0.458,0.198 10 false 5 2.844,1.104 3.302,1.302 0.458,0.198 10 false 6 2.854,1.469 3.313,1.667 0.458,0.198 10 false 4 2.844,0.729 3.302,0.927 0.458,0.198 10 false 3 2.854,2 3.313,2.198 0.458,0.198 10 false 3 2.854,2.354 3.313,2.552 0.458,0.198 10 false 2 2.844,2.719 3.302,2.917 0.458,0.198 10 false 1 2.844,3.271 3.302,3.469 0.458,0.198 10 false 3 2.844,4.583 3.302,4.781 0.458,0.198 10 false 3 2.844,3.635 3.302,3.833 0.458,0.198 10 false 2 2.854,4.938 3.313,5.135 0.458,0.198 10 false 2 2.854,6.219 3.313,6.417 0.458,0.198 10 false 2 2.854,5.854 3.313,6.052 0.458,0.198 10 false 3 2.844,4 3.302,4.198 0.458,0.198 10 false 1 2.844,5.302 3.302,5.5 0.458,0.198 10 false 1 2.854,6.573 3.313,6.771 0.458,0.198 10 false 1 2.844,7.917 3.302,8.115 0.458,0.198 10 false 1 2.844,7.552 3.302,7.75 0.458,0.198 10 false 2 2.833,7.177 3.292,7.375 0.458,0.198 10 false 3 0.521,0.656 2.021,1.448 1.5,0.792 10 false Throttle Body with Motor Assembly 0.5,2.208 2.354,2.531 1.854,0.323 10 false Crankshaft Position Sensor 0.51,3.479 1.917,4.208 1.406,0.729 10 false VVT Sensor (for Intake Camshaft of Bank 1) 0.521,4.802 2.063,5.531 1.542,0.729 10 false VVT Sensor (for Exhaust Camshaft of Bank 1) 0.521,6.094 1.927,6.823 1.406,0.729 10 false VVT Sensor (for Intake Camshaft of Bank 2) 0.521,7.406 2.063,8.135 1.542,0.729 10 false VVT Sensor (for Exhaust Camshaft of Bank 2) 2.563,0.479 3.021,0.677 0.458,0.198 10 false VC 2.573,0.833 3.031,1.031 0.458,0.198 10 false E2 2.479,1.198 2.938,1.396 0.458,0.198 10 false VTA 2.417,1.563 2.875,1.76 0.458,0.198 10 false VTA2 2.542,2.083 3,2.281 0.458,0.198 10 false VC 2.51,2.438 2.969,2.635 0.458,0.198 10 false NE- 2.531,3.375 2.99,3.573 0.458,0.198 10 false VC 2.417,3.719 2.875,3.917 0.458,0.198 10 false VVR- 2.396,4.094 2.854,4.292 0.458,0.198 10 false VVR+ 2.479,4.677 2.938,4.875 0.458,0.198 10 false VC2 2.521,5.021 2.979,5.219 0.458,0.198 10 false EX- 2.5,5.396 2.958,5.594 0.458,0.198 10 false EX+ 2.531,5.958 2.99,6.156 0.458,0.198 10 false VC 2.438,6.302 2.896,6.5 0.458,0.198 10 false VVL- 2.406,6.688 2.865,6.885 0.458,0.198 10 false VVL+ 2.49,7.281 2.948,7.479 0.458,0.198 10 false VC2 2.521,7.635 2.979,7.833 0.458,0.198 10 false EX- 2.49,2.823 2.948,3.021 0.458,0.198 10 false NE+ 2.5,8.021 2.958,8.219 0.458,0.198 10 false EX+ 5.271,8.021 5.729,8.219 0.458,0.198 10 false EV2+ 5.75,8.438 6.208,8.635 0.458,0.198 10 false ECM 5.271,6.698 5.729,6.896 0.458,0.198 10 false VV2+ 5.271,6.26 5.729,6.458 0.458,0.198 10 false VV2- 5.26,5.875 5.719,6.073 0.458,0.198 10 false VCV2 5.271,5.417 5.729,5.615 0.458,0.198 10 false EV1+ 5.281,4.104 5.74,4.302 0.458,0.198 10 false VV1+ 5.271,3.656 5.729,3.854 0.458,0.198 10 false VV1- 5.26,3.281 5.719,3.479 0.458,0.198 10 false VCV1 5.26,2.813 5.719,3.01 0.458,0.198 10 false NE+ 5.271,2.354 5.729,2.552 0.458,0.198 10 false NE- 5.281,2 5.74,2.198 0.458,0.198 10 false VCNE 5.271,1.219 5.729,1.417 0.458,0.198 10 false VTA1 6.292,0.219 6.75,0.417 0.458,0.198 10 false 5 V 5.281,0.385 5.74,0.583 0.458,0.198 10 false VCTA 5.271,1.573 5.729,1.771 0.458,0.198 10 false VTA2 4.938,0.313 5.24,0.51 0.302,0.198 10 false 121 4.938,0.677 5.24,0.875 0.302,0.198 10 false 120 4.938,1.042 5.24,1.24 0.302,0.198 10 false 122 4.979,1.396 5.281,1.594 0.302,0.198 10 false 89 4.979,1.927 5.292,2.167 0.313,0.24 10 false 96 4.99,2.281 5.302,2.521 0.313,0.24 10 false 95 4.948,2.646 5.26,2.885 0.313,0.24 10 false 128 4.979,3.208 5.292,3.448 0.313,0.24 10 false 99 4.938,3.563 5.25,3.802 0.313,0.24 10 false 100 4.938,3.927 5.25,4.167 0.313,0.24 10 false 132 4.948,5.24 5.26,5.479 0.313,0.24 10 false 131 4.99,5.792 5.302,6.031 0.313,0.24 10 false 98 4.99,6.156 5.302,6.396 0.313,0.24 10 false 97 4.948,6.521 5.26,6.76 0.313,0.24 10 false 129 4.938,7.844 5.25,8.083 0.313,0.24 10 false 130 4.969,8.052 5.281,8.292 0.313,0.24 10 false C1 4.969,6.719 5.281,6.958 0.313,0.24 10 false C1 4.979,6.333 5.292,6.573 0.313,0.24 10 false C1 4.979,5.969 5.292,6.208 0.313,0.24 10 false C1 4.969,5.438 5.281,5.677 0.313,0.24 10 false C1 4.969,4.125 5.281,4.365 0.313,0.24 10 false C1 4.979,3.76 5.292,4 0.313,0.24 10 false C1 4.979,3.385 5.292,3.625 0.313,0.24 10 false C1 4.969,2.823 5.281,3.063 0.313,0.24 10 false C1 4.969,2.469 5.281,2.708 0.313,0.24 10 false C1 4.969,2.115 5.281,2.354 0.313,0.24 10 false C1 4.969,1.594 5.281,1.833 0.313,0.24 10 false C1 4.979,1.24 5.292,1.479 0.313,0.24 10 false C1 4.958,0.865 5.271,1.104 0.313,0.24 10 false C1 4.969,0.5 5.281,0.74 0.313,0.24 10 false C1 5.281,0.74 5.74,0.938 0.458,0.198 10 false ETA

A376974E02
4.958,0.688 5.417,0.885 0.458,0.198 10 false A43 4.948,1.052 5.406,1.25 0.458,0.198 10 false A43 4.948,1.417 5.406,1.615 0.458,0.198 10 false A43 4.958,1.781 5.417,1.979 0.458,0.198 10 false A43 4.958,2.146 5.417,2.344 0.458,0.198 10 false A43 4.958,2.51 5.417,2.708 0.458,0.198 10 false A43 5,3.083 5.458,3.281 0.458,0.198 10 false C1 5,3.448 5.458,3.646 0.458,0.198 10 false C1 5,3.813 5.458,4.01 0.458,0.198 10 false C1 5.01,4.177 5.469,4.375 0.458,0.198 10 false C1 5,4.99 5.458,5.188 0.458,0.198 10 false C1 5.01,5.354 5.469,5.552 0.458,0.198 10 false C1 5.01,6.615 5.469,6.813 0.458,0.198 10 false C1 5.365,4.885 5.823,5.083 0.458,0.198 10 false ETHW 5.354,3.344 5.813,3.542 0.458,0.198 10 false E2G 5.354,2.99 5.813,3.188 0.458,0.198 10 false VC 5.354,1.688 5.813,1.885 0.458,0.198 10 false EPA2 5.344,1.323 5.802,1.521 0.458,0.198 10 false EPA 5.344,0.958 5.802,1.156 0.458,0.198 10 false VCP2 5.344,0.594 5.802,0.792 0.458,0.198 10 false VCPA 5.354,2.146 5.813,2.344 0.458,0.198 10 false VPA 5.354,2.51 5.813,2.708 0.458,0.198 10 false VPA2 5.365,3.813 5.823,4.01 0.458,0.198 10 false VG 5.365,4.177 5.823,4.375 0.458,0.198 10 false THA 5.365,5.354 5.823,5.552 0.458,0.198 10 false PR 5.354,6.604 5.813,6.802 0.458,0.198 10 false PFL 5,0.51 5.458,0.708 0.458,0.198 10 false 49 4.99,0.875 5.448,1.073 0.458,0.198 10 false 52 4.99,1.24 5.448,1.438 0.458,0.198 10 false 48 5,1.604 5.458,1.802 0.458,0.198 10 false 51 5,1.969 5.458,2.167 0.458,0.198 10 false 47 4.99,2.333 5.448,2.531 0.458,0.198 10 false 50 5,2.917 5.458,3.115 0.458,0.198 10 false 90 4.969,3.281 5.427,3.479 0.458,0.198 10 false 115 4.969,3.646 5.427,3.844 0.458,0.198 10 false 116 4.969,4 5.427,4.198 0.458,0.198 10 false 102 4.969,4.802 5.427,5 0.458,0.198 10 false 133 5.021,5.188 5.479,5.385 0.458,0.198 10 false 87 4.969,6.438 5.427,6.635 0.458,0.198 10 false 134 2.896,5.781 3.354,5.979 0.458,0.198 10 false 1 2.917,6.146 3.375,6.344 0.458,0.198 10 false 3 2.927,6.51 3.385,6.708 0.458,0.198 10 false 2 2.906,4.531 3.323,4.76 0.417,0.229 10 false 1 2.917,2.979 3.333,3.208 0.417,0.229 10 false 3 2.917,4.885 3.375,5.083 0.458,0.198 10 false 2 2.927,3.688 3.385,3.885 0.458,0.198 10 false 1 2.927,5.25 3.385,5.448 0.458,0.198 10 false 3 2.927,3.333 3.385,3.531 0.458,0.198 10 false 2 2.938,4.073 3.396,4.271 0.458,0.198 10 false 4 2.917,0.594 3.375,0.792 0.458,0.198 10 false 4 2.906,0.938 3.323,1.167 0.417,0.229 10 false 1 2.917,1.313 3.375,1.51 0.458,0.198 10 false 5 2.917,1.677 3.375,1.875 0.458,0.198 10 false 2 2.917,2.406 3.375,2.604 0.458,0.198 10 false 3 2.906,2.021 3.365,2.219 0.458,0.198 10 false 6 2.438,0.688 3.031,0.938 0.594,0.25 10 false VCPA 2.448,1.042 3.042,1.292 0.594,0.25 10 false VCP2 2.521,1.417 3.115,1.667 0.594,0.25 10 false EPA 2.448,1.781 3.042,2.031 0.594,0.25 10 false EPA2 2.521,2.146 3.115,2.396 0.594,0.25 10 false VPA 2.458,2.49 3.052,2.74 0.594,0.25 10 false VPA2 2.646,3.073 3.24,3.323 0.594,0.25 10 false 5V 2.542,3.438 3.135,3.688 0.594,0.25 10 false E2G 2.625,3.802 3.219,4.052 0.594,0.25 10 false FG 2.552,4.167 3.146,4.417 0.594,0.25 10 false THA 2.635,4.625 3.229,4.875 0.594,0.25 10 false VC 2.646,4.979 3.24,5.229 0.594,0.25 10 false E2 2.625,5.344 3.219,5.594 0.594,0.25 10 false PR 2.625,5.885 3.219,6.135 0.594,0.25 10 false VC 2.635,6.229 3.229,6.479 0.594,0.25 10 false E2 2.573,6.615 3.167,6.865 0.594,0.25 10 false PFL 0.583,5.875 1.177,6.125 0.594,0.25 10 false C77 0.583,4.615 1.177,4.865 0.594,0.25 10 false C76 0.563,3.104 1.156,3.354 0.594,0.25 10 false C63 0.563,0.719 1.156,0.969 0.594,0.25 10 false A53 0.563,0.885 2.135,1.281 1.573,0.396 10 false Accelerator Pedal Sensor Assembly 0.552,3.26 1.833,3.854 1.281,0.594 10 false Mass Air Flow Meter Sub-assembly 0.583,4.771 2.156,5.479 1.573,0.708 10 false Fuel Pressure Sensor (for High Pressure Side) 0.583,6.042 2.167,6.5 1.583,0.458 10 false Fuel Pressure Sensor (for Low Pressure Side)


CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK EFI NO. 2 FUSE VOLTAGE

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK EFI NO. 2 FUSE VOLTAGE
A400031C01
1.844,3.104 2.99,2.573 true 1.656,3.021 1.969,3.219 0.313,0.198 10 false *2 0.135,0.104 0.448,0.302 0.313,0.198 10 false *1
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 EFI NO. 2 Fuse


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (EFI NO. 2 fuse) - Body ground Ignition switch ON 11 to 14 V


HINT:
·

Check the fuse with it installed to the No. 1 engine room relay block and No. 1 junction block assembly.

·

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.




Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

5.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)
a.

Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

6.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1))

B

6.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1))
a.

Disconnect the VVT sensor (for intake camshaft of bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

7.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2))

B

REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1)

7.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2))
a.

Disconnect the VVT sensor (for intake camshaft of bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

8.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1))

B

REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2)

8.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1))
a.

Disconnect the VVT sensor (for exhaust camshaft of bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

9.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2))

B

REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1)

9.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2))
a.

Disconnect the VVT sensor (for exhaust camshaft of bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

10.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))

B

REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2)

10.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))
a.

Disconnect the fuel pressure sensor (for high pressure side) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

11.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE))

B

REPLACE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY LH (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))

11.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE))
a.

Disconnect the fuel pressure sensor (for low pressure side) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (for low pressure side).

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

12.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)

B

REPLACE FUEL DELIVERY PIPE RH (FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE))

12.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

13.CHECK HARNESS AND CONNECTOR

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

13.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Disconnect the crankshaft position sensor connector.


d.

Disconnect the VVT sensor (for intake camshaft of bank 1) connector.


e.

Disconnect the VVT sensor (for intake camshaft of bank 2) connector.


f.

Disconnect the VVT sensor (for exhaust camshaft of bank 1) connector.


g.

Disconnect the VVT sensor (for exhaust camshaft of bank 2) connector.


h.

Disconnect the fuel pressure sensor (for high pressure side) connector.


i.

Disconnect the fuel pressure sensor (for low pressure side) connector.


j.

Disconnect the mass air flow meter sub-assembly connector.


k.

Disconnect the ECM connectors.


l.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-121 (VCTA) - Body ground Always 10 kΩ or higher
A43-49 (VCPA) - Body ground Always 10 kΩ or higher
A43-52 (VCP2) - Body ground Always 10 kΩ or higher
C1-96 (VCNE) - Body ground Always 10 kΩ or higher
C1-99 (VCV1) - Body ground Always 10 kΩ or higher
C1-98 (VCV2) - Body ground Always 10 kΩ or higher
C1-90 (VC) - Body ground Always 10 kΩ or higher
A43-2 (+B) - 1 (EFI NO. 2 fuse) Always Below 1 Ω
A43-3 (+B2) - 1 (EFI NO. 2 fuse) Always Below 1 Ω
A43-2 (+B) - Body ground Always 10 kΩ or higher
A43-3 (+B2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR