Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0299070 SFI SYSTEM C

2GR-FKS ENGINE CONTROL  SFI SYSTEM  P21951D  O2 Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Circuit Current Out of Range  P219523  O2 Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Signal Stuck Low  P21961D  O2 Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Circuit Current Out of Range  P219624  O2 Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Signal Stuck High  P21971D  O2 Sensor Signal Biased/Stuck Lean Bank 2 Sensor 1 Circuit Current Out of Range  P219723  O2 Sensor Signal Biased/Stuck Lean Bank 2 Sensor 1 Signal Stuck Low  P21981D  O2 Sensor Signal Biased/Stuck Rich Bank 2 Sensor 1 Circuit Current Out of Range  P219824  O2 Sensor Signal Biased/Stuck Rich Bank 2 Sensor 1 Signal Stuck High  


DESCRIPTION

HINT:

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.


The air fuel ratio sensor generates voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection duration. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is a planar type and integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are a narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A306366E01
1.49,2.167 1,1.75 1,1.75 0.833,1.75 false 1.656,2.094 1.823,1.844 1.823,1.844 1.906,1.844 false 2.938,1.177 3.104,0.396 3.104,0.396 3.188,0.396 false 3.083,1.198 3.25,0.917 3.25,0.917 3.333,0.917 false 3.156,1.198 3.333,1.167 3.333,1.167 3.417,1.167 false 2.875,1.667 3.406,1.5 3.406,1.5 2.99,1.667 false 3.042,1.75 3.417,2.083 3.417,2.083 3.5,2.083 false 0.281,1.656 1.354,1.854 1.073,0.198 10 false Element 0.135,2.385 1.208,2.583 1.073,0.198 10 false Exhaust Gas 1.083,2.49 1.417,2.667 0.333,0.177 10 false A 1.802,2.49 2.135,2.667 0.333,0.177 10 false A 1.948,1.76 2.333,1.917 0.385,0.156 10 false Cover 3.26,0.219 4.417,0.583 1.156,0.365 10 false Solid Electrolyte (Zirconia Element) 3.385,0.833 4.052,0.99 0.667,0.156 10 false Alumina 3.458,1.083 4.125,1.24 0.667,0.156 10 false Heater 3.448,1.417 4.698,1.667 1.25,0.25 10 false Platinum Electrode 3.542,2 4.792,2.25 1.25,0.25 10 false Atmospheric Air 2.531,2.333 3.865,2.5 1.333,0.167 10 false A-A Cross Section 5.323,0.167 6.823,0.5 1.5,0.333 10 false ECM Monitored Air Fuel Ratio Sensor Voltage 5.563,2.25 6.896,2.417 1.333,0.167 10 false Air Fuel Ratio

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P21951D O2 Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Circuit Current Out of Range While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 2.2 mA or higher for 3 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (Bank 1 sensor 1) circuit

·

Air fuel ratio sensor (Bank 1 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure (for low pressure side)

·

Fuel pressure (for high pressure side)

·

Fuel injector assembly (for port injection)

·

Fuel injector assembly (for direct injection)

·

Fuel system

·

ECM


Comes on DTC stored SAE Code: P2195
P219523 O2 Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Signal Stuck Low Both of the following conditions are met for 5 seconds or more (2 trip detection logic):
1.

Air fuel ratio sensor voltage is higher than 3.8 V.

2.

Heated oxygen sensor voltage is 0.21 V or higher.


·

Open or short in air fuel ratio sensor (Bank 1 sensor 1) circuit

·

Air fuel ratio sensor (Bank 1 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure (for low pressure side)

·

Fuel pressure (for high pressure side)

·

Fuel injector assembly (for port injection)

·

Fuel injector assembly (for direct injection)

·

Fuel system

·

ECM


Comes on DTC stored SAE Code: P2195
P21961D O2 Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Circuit Current Out of Range While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 0.47 mA for 3 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (Bank 1 sensor 1) circuit

·

Air fuel ratio sensor (Bank 1 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure (for low pressure side)

·

Fuel pressure (for high pressure side)

·

Fuel injector assembly (for port injection)

·

Fuel injector assembly (for direct injection)

·

Fuel system

·

ECM


Comes on DTC stored SAE Code: P2196
P219624 O2 Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Signal Stuck High Both of the following conditions are met for 5 seconds or more (2 trip detection logic):
1.

Air fuel ratio sensor voltage is less than 2.8 V.

2.

Heated oxygen sensor voltage is less than 0.7 V.


·

Open or short in air fuel ratio sensor (Bank 1 sensor 1) circuit

·

Air fuel ratio sensor (Bank 1 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure (for low pressure side)

·

Fuel pressure (for high pressure side)

·

Fuel injector assembly (for port injection)

·

Fuel injector assembly (for direct injection)

·

Fuel system

·

ECM


Comes on DTC stored SAE Code: P2196
P21971D O2 Sensor Signal Biased/Stuck Lean Bank 2 Sensor 1 Circuit Current Out of Range While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 2.2 mA or higher for 3 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (Bank 2 sensor 1) circuit

·

Air fuel ratio sensor (Bank 2 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure (for low pressure side)

·

Fuel pressure (for high pressure side)

·

Fuel injector assembly (for port injection)

·

Fuel injector assembly (for direct injection)

·

Fuel system

·

ECM


Comes on DTC stored SAE Code: P2197
P219723 O2 Sensor Signal Biased/Stuck Lean Bank 2 Sensor 1 Signal Stuck Low Both of the following conditions are met for 5 seconds or more (2 trip detection logic):
1.

Air fuel ratio sensor voltage is higher than 3.8 V.

2.

Heated oxygen sensor voltage is 0.21 V or higher.


·

Open or short in air fuel ratio sensor (Bank 2 sensor 1) circuit

·

Air fuel ratio sensor (Bank 2 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure (for low pressure side)

·

Fuel pressure (for high pressure side)

·

Fuel injector assembly (for port injection)

·

Fuel injector assembly (for direct injection)

·

Fuel system

·

ECM


Comes on DTC stored SAE Code: P2197
P21981D O2 Sensor Signal Biased/Stuck Rich Bank 2 Sensor 1 Circuit Current Out of Range While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 0.47 mA for 3 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (Bank 2 sensor 1) circuit

·

Air fuel ratio sensor (Bank 2 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure (for low pressure side)

·

Fuel pressure (for high pressure side)

·

Fuel injector assembly (for port injection)

·

Fuel injector assembly (for direct injection)

·

Fuel system

·

ECM


Comes on DTC stored SAE Code: P2198
P219824 O2 Sensor Signal Biased/Stuck Rich Bank 2 Sensor 1 Signal Stuck High Both of the following conditions are met for 5 seconds or more (2 trip detection logic):
1.

Air fuel ratio sensor voltage is less than 2.8 V.

2.

Heated oxygen sensor voltage is less than 0.7 V.


·

Open or short in air fuel ratio sensor (Bank 2 sensor 1) circuit

·

Air fuel ratio sensor (Bank 2 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure (for low pressure side)

·

Fuel pressure (for high pressure side)

·

Fuel injector assembly (for port injection)

·

Fuel injector assembly (for direct injection)

·

Fuel system

·

ECM


Comes on DTC stored SAE Code: P2198

HINT:
·

DTCs P21951D, P219523, P21961D and P219624 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.

·

DTCs P21971D, P219723, P21981D and P219824 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.

·

When any of these DTCs are stored, check the air fuel ratio sensor voltage output by entering the following menus on the GTS: Powertrain / Engine / Data List / A/F (O2) Sensor Voltage B1S1 or A/F (O2) Sensor Voltage B2S1.

·

Short-term fuel trim values can also be read using the GTS.

·

The ECM regulates the voltages at the A1A+, A2A+, A1A- and A2A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor output voltage cannot be confirmed without using the GTS.

·

If an air fuel ratio sensor malfunction is detected, the ECM will store a DTC.



MONITOR DESCRIPTION

Sensor Voltage Detection Monitor:

Under air fuel ratio feedback control, If the air fuel ratio sensor output voltage is less than 2.8 V (very rich condition) for 5 seconds despite the heated oxygen sensor output voltage being less than 0.7 V, the ECM stores DTC P219624 or P219824. Alternatively, if the air fuel ratio sensor output voltage is higher than 3.8 V (very lean condition) for 5 seconds despite the heated oxygen sensor output voltage being 0.21 V or higher, DTC P219523 or P219723 is stored.


Sensor Current Detection Monitor:

A rich air fuel mixture causes a low air fuel ratio sensor current, and a lean air fuel mixture causes a high air fuel ratio sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the air fuel ratio sensor current during fuel-cut and detects any abnormal current values.

If the air fuel ratio sensor output is 2.2 mA or higher for 3 seconds of cumulative time, the ECM interprets this as a malfunction in the air fuel ratio sensor and stores DTC P21951D or 21971D (stuck on high side). If the air fuel ratio sensor output is less than 0.47 mA for 3 seconds or more of cumulative time, the ECM stores DTC P21961D or P21981D (stuck on low side).


A284399E03
2.385,2.281 2.188,1.594 2.188,1.594 2.323,1.594 false 4.406,2.281 4.26,1.667 4.26,1.667 4.396,1.667 false 5.771,2.281 5.677,1.656 5.677,1.656 5.813,1.656 false 0.177,0.115 2.76,0.323 2.583,0.208 10 Air Fuel Ratio Sensor Current Monitor 2.833,0.323 6.094,0.51 3.26,0.188 10 Cumulative Time "t" = t1 + t2 = 3 seconds or more 1.469,1.208 1.854,1.396 0.385,0.188 10 OFF 1.49,0.917 1.875,1.104 0.385,0.188 10 ON 0.646,1.073 1.24,1.281 0.594,0.208 10 Fuel-cut 0.448,2.833 1.802,3.104 1.354,0.271 10 High Side Threshold 2.375,1.51 3.729,1.781 1.354,0.271 10 Delay (3 seconds) 0.49,3.49 1.844,3.76 1.354,0.271 10 Low Side Threshold 0.479,2.219 1.833,2.49 1.354,0.271 10 Sensor Current (mA) 4.448,1.563 5.802,1.833 1.354,0.271 10 Delay (3 seconds) 5.865,1.563 7.073,1.823 1.208,0.26 10 Delay (3 seconds) 6.01,3.813 6.292,4.031 0.281,0.219 10 t2 4.708,3.813 4.99,4.031 0.281,0.219 10 t1 2.385,3.635 3.74,3.906 1.354,0.271 10 3 seconds or more 4.708,4.24 6.365,4.427 1.656,0.188 10 Abnormal Sensor Output 2.417,4.25 4.073,4.438 1.656,0.188 10 Normal Sensor Output 6.667,4.26 7.031,4.448 0.365,0.188 10 Time

MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor
Required Sensors/Components (Related) Heated oxygen sensor
Frequency of Operation Continuous: Sensor voltage detection monitor
Once per driving cycle: Sensor current detection monitor
Duration 3 seconds: Sensor current detection monitor
5 seconds: Sensor voltage detection monitor

TYPICAL ENABLING CONDITIONS

Sensor Voltage Detection Monitor
Time after engine start 30 seconds or more
Battery voltage 11 V or higher
Air fuel ratio sensor status Activated
Fuel system status Closed-loop

Sensor Current Detection Monitor
Battery voltage 11 V or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [11 psi(abs)] or higher
Air fuel ratio sensor status Activated
Continuous time of fuel-cut 3 seconds or more, and less than 10 seconds

TYPICAL MALFUNCTION THRESHOLDS

P2195 and P2197: Sensor Voltage Detection Monitor (Lean Side Malfunction)
Heated oxygen sensor voltage 0.21 V or higher
Air fuel ratio sensor voltage Higher than 3.8 V

P2196 and P2198: Sensor Voltage Detection Monitor (Rich Side Malfunction)
Heated oxygen sensor voltage Less than 0.7 V
Air fuel ratio sensor voltage Less than 2.8 V

P2195 and P2197: Sensor Current Detection Monitor (High Side Malfunction)
Duration of following condition 3 seconds or more
Air fuel ratio sensor current 2.2 mA or higher

P2196 and P2198: Sensor Current Detection Monitor (Low Side Malfunction)
Duration of following condition 3 seconds or more
Air fuel ratio sensor current Less than 0.47 mA

CONFIRMATION DRIVING PATTERN

A283818E28
2.448,1.51 3.052,0.698 3.052,0.698 2.833,0.698 true 5.448,1.667 5.75,0.583 true 5.021,1.521 4.5,1.521 false 6.333,2.25 5.375,2.25 false 4.052,3.531 3.823,3.354 true 4.927,1.677 4.5,0.583 true 5.542,3.167 5.708,3.167 5.708,3.167 5.5,2.74 true 4.708,2.958 4.875,2.958 4.875,2.958 4.99,2.729 true 0.073,0.24 3.25,0.5 3.177,0.26 10 false Engine Coolant Temperature: 75°C or higher 0.156,0.865 1.104,1.094 0.948,0.229 10 false Vehicle Speed 1.156,0.604 2.792,1.021 1.635,0.417 10 false Between 60 and 100 km/h 0.719,2.281 1.167,2.583 0.448,0.302 10 false Idling 1.25,2.865 2.083,3.083 0.833,0.219 10 false Warming up 2.49,2.875 3.219,3.396 0.729,0.521 10 false 10 minutes or more 3.427,1.458 4.479,1.854 1.052,0.396 10 false 60 km/h or more 3.396,0.448 4.542,0.865 1.146,0.417 10 false Accelerator Pedal Depressed 4.667,0.708 5.667,0.917 1,0.208 10 false At least 3 times 5.823,0.438 7.052,0.958 1.229,0.521 10 false Accelerator Pedal Released (Fuel-cut) 6.417,2.146 6.979,2.51 0.563,0.365 10 false 10 km/h 6.25,2.552 6.667,2.802 0.417,0.25 10 false Time 4.375,3.073 5.604,3.344 1.229,0.271 10 false 5 seconds or more 4.094,3.469 5.417,3.667 1.323,0.198 10 false Refer to figure below 3.448,2.865 4.729,3.229 1.281,0.365 10 false 10 seconds or more 1.552,2.167 1.813,2.385 0.26,0.219 10 false [A] 2.708,1.302 2.969,1.521 0.26,0.219 10 false [B] 3.844,2.167 4.083,2.417 0.24,0.25 10 false [C] 4.99,1.302 5.25,1.521 0.26,0.219 10 false [D] 5.5,1.594 5.76,1.813 0.26,0.219 10 false [E] 6.083,3.115 6.344,3.333 0.26,0.219 10 false [F]

A268862E15
3.646,2.625 3.958,0.885 false 3.375,2.625 2.167,0.719 2.167,0.719 2.292,0.719 false 2.271,1.385 2.979,1.385 false 0.104,0.042 3.042,0.24 2.938,0.198 10 false Driving Pattern Detail for [C] through [E]: 0.5,0.594 1.729,0.906 1.229,0.313 10 false Vehicle Speed 2.823,0.156 7,0.406 4.177,0.25 10 false Cumulative Detection Period "t" = t1 + t2 + t3 = 3 seconds or more 1.094,2.365 1.51,2.563 0.417,0.198 10 false Idling 2.188,2.948 2.698,3.229 0.51,0.281 10 false Idling 3.177,3.115 3.833,3.479 0.656,0.365 10 false 5 seconds or more 2.188,2.25 2.448,2.521 0.26,0.271 10 false [C] 3.031,1.146 3.313,1.469 0.281,0.323 10 false [D] 3.469,1.542 3.729,1.813 0.26,0.271 10 false [E] 2.375,0.635 3.563,0.833 1.188,0.198 10 false Delay (3 seconds) 4.01,0.75 5.448,0.948 1.438,0.198 10 false Detection Period t1 4.813,2.375 4.99,2.625 0.177,0.25 10 false t2 6.042,2.396 6.302,2.635 0.26,0.24 10 false t3 6.49,2.781 6.875,2.979 0.385,0.198 10 false Time 4.375,3.115 5.031,3.479 0.656,0.365 10 false 5 seconds or more 5.604,3.115 6.26,3.479 0.656,0.365 10 false 5 seconds or more 1.688,1.292 2.208,1.76 0.521,0.469 10 false 60 km/h or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

8.

Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for at least 10 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

With the shift lever in M [C], accelerate the vehicle to 60 km/h (37 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Soon after performing step [D] above, release the accelerator pedal for at least 5 seconds without depressing the brake pedal in order to execute fuel-cut control [E].

11.

Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).

12.

Repeat steps [C] through [E] above at least 3 times in one driving cycle.

13.

Enter the following menus: Powertrain / Engine / Trouble Codes [F].

14.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

16.

Input the DTC: P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D or P219824.

17.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F] again.




WIRING DIAGRAM

A371564E03
0.896,5.594 1.969,5.792 1.073,0.198 10 false Battery 0.917,3.896 2.146,4.396 1.229,0.5 10 false Semiconductor Pwr Integration ECU 0.99,2.885 2.219,3.083 1.229,0.198 10 false EFI MAIN 0.688,3.208 1.917,3.406 1.229,0.198 10 false EFI-MAIN 0.885,1.552 2.26,1.75 1.375,0.198 10 false EFI NO. 2 1.375,1.26 1.833,1.458 0.458,0.198 10 false A/F 0.354,0.74 1.125,0.969 0.771,0.229 10 false A/F HTR 2.25,0.438 2.406,0.635 0.156,0.198 10 false 1 2.219,0.604 2.531,0.802 0.313,0.198 10 false 1F 2.219,2.563 2.531,2.76 0.313,0.198 10 false 1G 2.271,2.406 2.427,2.604 0.156,0.198 10 false 6 0.573,3.688 0.729,3.885 0.156,0.198 10 false B 0.688,4.969 1.76,5.167 1.073,0.198 10 false FL MAIN 3.448,1.896 4.813,2.5 1.365,0.604 10 false Air Fuel Ratio Sensor (Bank 1 Sensor 1) 3.448,1.729 3.906,1.927 0.458,0.198 10 false C33 3.656,1.25 4.104,1.51 0.448,0.26 10 false A1A- 4.094,1.24 4.708,1.438 0.615,0.198 10 false A1A+ 3.667,0.51 3.979,0.708 0.313,0.198 10 false +B 4.063,0.51 4.677,0.708 0.615,0.198 10 false HA1A 3.5,0.51 3.656,0.708 0.156,0.198 10 false 2 3.5,1.26 3.656,1.458 0.156,0.198 10 false 4 4.51,1.25 4.667,1.448 0.156,0.198 10 false 3 4.5,0.51 4.656,0.708 0.156,0.198 10 false 1 3.646,2.969 3.958,3.167 0.313,0.198 10 false +B 4.052,2.969 4.667,3.167 0.615,0.198 10 false HA2A 4.073,3.719 4.688,3.917 0.615,0.198 10 false A2A+ 3.635,3.719 4.083,3.979 0.448,0.26 10 false A2A- 4.479,2.969 4.635,3.167 0.156,0.198 10 false 1 4.479,3.719 4.635,3.917 0.156,0.198 10 false 3 3.479,2.969 3.635,3.167 0.156,0.198 10 false 2 3.49,3.719 3.646,3.917 0.156,0.198 10 false 4 3.417,4.198 3.875,4.396 0.458,0.198 10 false C32 3.417,4.365 4.781,4.969 1.365,0.604 10 false Air Fuel Ratio Sensor (Bank 2 Sensor 1) 5.188,2.833 5.344,3.031 0.156,0.198 10 false * 5.167,5.438 5.323,5.635 0.156,0.198 10 false * 5.521,0.604 5.979,0.802 0.458,0.198 10 false C1 5.521,1.385 5.979,1.583 0.458,0.198 10 false C1 5.521,2.448 5.979,2.646 0.458,0.198 10 false C1 5.51,3.083 5.969,3.281 0.458,0.198 10 false C1 5.5,3.865 5.958,4.063 0.458,0.198 10 false C1 5.521,5.021 5.979,5.219 0.458,0.198 10 false C1 5.49,5.875 5.948,6.073 0.458,0.198 10 false A43 5.542,0.438 6,0.635 0.458,0.198 10 false 52 5.49,1.219 5.948,1.417 0.458,0.198 10 false 125 5.479,2.26 5.938,2.458 0.458,0.198 10 false 126 5.531,2.906 5.99,3.104 0.458,0.198 10 false 17 5.479,3.688 5.938,3.885 0.458,0.198 10 false 123 5.531,5.708 5.99,5.906 0.458,0.198 10 false 46 5.49,4.854 5.948,5.052 0.458,0.198 10 false 124 6.208,6.396 6.667,6.594 0.458,0.198 10 false ECM 5.844,5.771 6.458,5.969 0.615,0.198 10 false MREL 5.844,0.51 6.458,0.708 0.615,0.198 10 false HA1A 5.854,1.292 6.469,1.49 0.615,0.198 10 false A1A+ 5.854,2.354 6.469,2.552 0.615,0.198 10 false A1A- 5.844,2.99 6.458,3.188 0.615,0.198 10 false HA2A 5.854,3.771 6.469,3.969 0.615,0.198 10 false A2A+ 5.854,4.927 6.469,5.125 0.615,0.198 10 false A2A- 1.75,6.115 3.438,6.313 1.688,0.198 10 false *: Shielded 0.667,3.51 0.823,3.708 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D OR P219824)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D or P219824 is output A
DTC P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D or P219824 and P013613, P013617, P01361C, P015613, P015617 or P01561C are output
DTC P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D or P219824 and other DTCs are output B


HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.




A

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?


Result:
Proceed to
YES
NO



YES

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D OR P219824)

NO

4.READ VALUE USING GTS (A/F (O2) SENSOR CURRENT)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D OR P219824)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

j.

Input the DTC: P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D or P219824.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D or P219824 is output)
B




A

DTC CAUSED BY RUNNING OUT OF FUEL

B

4.READ VALUE USING GTS (A/F (O2) SENSOR CURRENT)
4.READ VALUE USING GTS (A/F (O2) SENSOR CURRENT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Enter the following menus: Powertrain / Engine / Data List / A/F (O2) Sensor Current B1S1 or A/F (O2) Sensor Current B2S1.

Powertrain > Engine > Data List
Tester Display
A/F (O2) Sensor Current B1S1
A/F (O2) Sensor Current B2S1
50003 372 230,432

f.

Check the test value of the air fuel ratio sensor output current during fuel-cut, referring to the Driving Pattern Detail for [C] through [E] in Confirmation Driving Pattern.

HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the GTS.



Result:
Test Value Proceed to
Within normal range
(0.47 mA or higher, and less than 2.2 mA)
A
Outside normal range
(less than 0.47 mA, or 2.2 mA or higher)
B




A

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

15.REPLACE AIR FUEL RATIO SENSOR
5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


e.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


f.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2 or A/F (O2) Sensor Voltage B2S1 and O2 Sensor Voltage B2S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
A/F (O2) Sensor Voltage B1S1
A/F (O2) Sensor Voltage B2S1
O2 Sensor Voltage B1S2
O2 Sensor Voltage B2S2
50004 372 8 225,512,218,510

g.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


h.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2 A/F (O2) Sensor Voltage B2S1 and O2 Sensor Voltage B2S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS Display (Sensor) Injection Volume Status Voltage
A/F (O2) Sensor Voltage B1S1
A/F (O2) Sensor Voltage B2S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2 Sensor Voltage B1S2
O2 Sensor Voltage B2S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


Result:
Status of A/F (O2) Sensor Voltage B1S1 or A/F (O2) Sensor Voltage B2S1 Status of O2 Sensor Voltage B1S2 or O2 Sensor Voltage B2S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to
Lean Lean Actual air fuel ratio lean A
Rich Rich Actual air fuel ratio rich
Lean Lean/Rich Air fuel ratio sensor malfunction B
Rich Lean/Rich Air fuel ratio sensor malfunction
Lean/Rich Lean/Rich Normal


Lean: During the Control the Injection Volume for A/F Sensor of the Active Test, the air fuel ratio sensor output voltages (A/F (O2) Sensor Voltage B1S1 and A/F (O2) Sensor Voltage B2S1) are consistently higher than 3.4 V, and the heated oxygen sensor output voltages (O2 Sensor Voltage B1S2 and O2 Sensor Voltage B2S2) are consistently below 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor of the Active Test, the A/F (O2) Sensor Voltage B1S1 and A/F (O2) Sensor Voltage B2S1 are consistently below 3.1 V, and the O2 Sensor Voltage B1S2 and O2 Sensor Voltage B2S2 are consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the air fuel ratio sensor or heated oxygen sensor alternates correctly.


HINT:

Refer to "Data List / Active Test" [A/F (O2) Sensor Voltage B1S1, A/F (O2) Sensor Voltage B2S1, O2 Sensor Voltage B1S2 and O2 Sensor Voltage B2S2].

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST




A

6.CHECK INTAKE SYSTEM

B

15.REPLACE AIR FUEL RATIO SENSOR
6.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2GR-FKS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from the intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

7.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE INTAKE SYSTEM

7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)

NG

REPAIR OR REPLACE EXHAUST SYSTEM

8.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)
a.

Check the fuel pressure (for low pressure side).

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

9.INSPECT FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)

NG

14.CHECK FUEL LINE
9.INSPECT FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)
a.

Inspect the fuel injector assembly (for port injection) (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL INJECTOR(for Port Injection)>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (for port injection).

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (FUEL PRESSURE (HIGH))

NG

REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)

10.READ VALUE USING GTS (FUEL PRESSURE (HIGH))
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).

Powertrain > Engine > Data List
Tester Display
Fuel Pressure (High)
50003 372 265

e.

Read the values.

Standard:

2400 to 19500 kPag (3000 rpm, engine warmed up, shift lever in P, A/C off).



Result:
Proceed to
OK
NG



OK

11.INSPECT FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION)

NG

REPAIR OR REPLACE FUEL SYSTEM (FOR HIGH PRESSURE SIDE)

11.INSPECT FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION)
a.

Inspect the fuel injector assembly (for direct injection).

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL INJECTOR(for Direct Injection)>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (for direct injection).

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

12.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION)

12.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D OR P219824)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D OR P219824)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

j.

Input the DTC: P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D or P219824.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D or P219824 is output)
B




A

END

B

14.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE FUEL SYSTEM

15.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

16.CHECK WHETHER DTC OUTPUT RECURS (DTC P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D OR P219824)
16.CHECK WHETHER DTC OUTPUT RECURS (DTC P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D OR P219824)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

j.

Input the DTC: P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D or P219824.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P21951D, P219523, P21961D, P219624, P21971D, P219723, P21981D or P219824 is output)
B




A

END

B