Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER(for AWD) › from 2018.09
RM3160E _52 Drivetrain _019687 AXLE AND DIFFERENTIAL _0109441 REAR AXLE CARRIER(for AWD) A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER(for AWD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48759 1.INSTALL LOWER CONTROL ARM PIN

a.
C199843N01
1.021,1.198 1.646,1.198 false 0.74,1.125 1.167,1.375 0.427,0.25 10 false SST

Secure the rear axle carrier sub-assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using SST, install a new lower control arm pin to the rear axle carrier sub-assembly as shown in the illustration.

SST
09650-17011  


Hide 42305 2.TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY

a.

Secure the rear axle carrier sub-assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C199841

Using a brass bar and a hammer, push out the bushing until it is positioned as shown in the illustration.

HINT:

Pushing out the bushing makes it easier to install the rear axle carrier sub-assembly.



c.
C199847C03
2.375,1.979 3.052,1.979 true 2.604,2.083 2.604,2.302 2.604,2.302 2.917,2.302 true 3.094,1.875 3.406,2.031 0.313,0.156 10 false *a 2.948,2.219 3.24,2.448 0.292,0.229 10 false *b 0.479,1.802 0.625,2.021 0.146,0.219 10 true A 0.563,2.896 0.75,3.063 0.188,0.167 10 true D 2.813,0.406 2.958,0.583 0.146,0.177 10 true B 0.865,0.771 1.01,0.958 0.146,0.188 10 true C 0.771,2.896 0.938,3.073 0.167,0.177 10 true D
*a Wooden Block
*b Jack


Temporarily install the rear axle carrier sub-assembly to the rear No. 1 suspension arm assembly with the spacer and nut (A).

NOTICE:

Fully tighten the nut (A) after stabilizing the suspension.



d.

Install the rear axle carrier sub-assembly to the rear No. 2 suspension arm assembly with the bolt (B) and nut.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

NOTICE:
·

Insert the bolt with the threaded end facing the front of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.




e.

Install the rear axle carrier sub-assembly to the rear upper control arm assembly with the bolt (C) and nut.

Torque:
145 N*m (1479 kgf*cm, 107 ft.*lbf)

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.




f.

Install the rear axle carrier sub-assembly to the rear lower shock absorber bracket sub-assembly with the 2 bolts (D).

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


g.

Slowly lower the rear No. 2 suspension arm assembly.


Hide 3.TEMPORARILY INSTALL PARKING BRAKE ASSEMBLY

a.
C293821

Temporarily install the parking brake assembly to the rear axle carrier sub-assembly with the nut.

NOTICE:
·

Do not twist the parking brake cable when installing the parking brake assembly.

·

Fully tighten the nut after installing the rear trailing arm assembly.




Hide 48780E 4.INSTALL REAR TRAILING ARM ASSEMBLY

Hide 5.INSTALL PARKING BRAKE ASSEMBLY

a.
C293052

Install the parking brake assembly with the nut.

Torque:
160 N*m (1632 kgf*cm, 118 ft.*lbf)


Hide 42440 6.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

Hide 89546 7.INSTALL REAR SPEED SENSOR

a.
C296196

Install the rear speed sensor to the rear trailing arm assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Do not twist the rear speed sensor when installing it.



b.
C293840

Install the rear speed sensor to the rear axle carrier sub-assembly with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not twist the rear speed sensor when installing it.



Hide 42431 8.INSTALL REAR DISC

Hide 42491 9.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 10.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

a.

Install the rear disc brake caliper assembly to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


b.
C293049

Install the rear flexible hose to the rear upper control arm assembly with the bolt.

Torque:
18.8 N*m (192 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not twist the rear flexible hose when installing it.

·

Do not damage the rear flexible hose when installing it.

·

If the rear flexible hose is damaged, replace it with a new one.




c.
C293048C02
1.458,0.813 1.958,0.813 true 1.354,1.396 1.635,1.396 true 1.271,0.708 1.448,0.906 0.177,0.198 10 true *1 1.156,1.271 1.333,1.479 0.177,0.208 10 true *2
*1 Rear Brake Tube
*2 Rear Flexible Hose
V100136

Clip


Install the rear flexible hose with a new clip.

NOTICE:

Install the clip as far as it will go.



d.

Using a union nut wrench, connect the rear flexible hose to the rear brake tube while holding the rear flexible hose with a wrench.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




Hide 42312B 11.INSTALL REAR AXLE SHAFT NUT

a.

Clean the threaded parts on the rear drive shaft assembly and a new rear axle shaft nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new rear drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.
C293043

Using a 30 mm socket wrench, while applying the parking brakes, temporarily install the rear axle shaft nut.

Torque:
294 N*m (2998 kgf*cm, 217 ft.*lbf)


c.
C296159

Using a chisel and hammer, stake the rear axle shaft nut.


Hide 12. BLEED BRAKE LINE

Hide 48720A 14.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

a.
C336800

Install the rear No. 1 suspension arm assembly with the nut.

Torque:
145 N*m (1479 kgf*cm, 107 ft.*lbf)


Hide 15.ADJUST PARKING BRAKE

Hide 16.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 17.INSPECT AND ADJUST REAR WHEEL ALIGNMENT