Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL (for Dynamic Torque Vectoring AWD)
RM37A0E _52 Drivetrain _086863 AXLE AND DIFFERENTIAL _0421147 REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL(for Dynamic Torque Vectoring AWD) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL(for Dynamic Torque Vectoring AWD)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear differential carrier oil seal and transmission coupling dust seal replacement are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Gas leaks from exhaust system Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Electro magnetic control coupling sub-assembly (Electro magnetic control coupling sub-assembly LH, electro magnetic control coupling sub-assembly RH)
·

ECU data initialization

·

ECU data write


Dynamic Torque Vectoring AWD System (Click here)
Torque vectoring differential carrier assembly
·

ECU data initialization

·

Disconnect system function check



CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 41330M 2.REMOVE TRANSMISSION COUPLING DUST SEAL

a.
C426356C01
2.031,2.49 2.146,2.698 2.146,2.698 2.313,2.698 true 0.906,1.26 1.094,1.479 1.094,1.479 1.281,1.479 false 2.354,2.635 2.771,2.885 0.417,0.25 10 true SST 1.292,1.385 1.542,1.583 0.25,0.198 10 false *1
*1 Transmission Coupling Dust Seal


Using SST, remove the transmission coupling dust seal from the electro magnetic control coupling sub-assembly.

SST
09308-00010  

NOTICE:

Do not damage the electro magnetic control coupling sub-assembly.



Hide 41110 3.REMOVE TORQUE VECTORING DIFFERENTIAL CARRIER ASSEMBLY

Hide 7.REMOVE ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY (for LH Side)

Hide 8.REMOVE ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 41201C 10.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL (for LH Side)

a.
C408438C01
2.906,0.833 3,1.083 3,1.083 3.156,1.083 true 3,0.333 2.667,0.333 2.667,0.333 2.667,0.417 false 2.635,1.333 2.885,1.333 false 1.083,1.385 0.833,1.885 0.833,1.885 0.417,1.885 true 3.042,0.271 3.375,0.521 0.333,0.25 10 false *1 3.198,1.021 3.365,1.271 0.167,0.25 10 false *a 0.25,1.823 0.583,2.073 0.333,0.25 10 false *b
*1 Rear Differential Carrier Oil Seal
*a Cut Position
*b Protective Tape


Using a knife, cut off the lip of the rear differential carrier oil seal.


b.

Using a screwdriver with its tip wrapped with protective tape, pry out the rear differential carrier oil seal.

NOTICE:

Do not damage the rear differential carrier assembly.



Hide 41201C 11.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL (for RH Side)

a.
C408436C01
2.927,0.833 3.01,1.083 3.01,1.083 3.177,1.083 true 2.667,0.417 2.667,0.333 2.667,0.333 2.917,0.333 true 1.417,1.313 0.917,1.813 0.917,1.813 0.667,1.813 true 2.958,0.271 3.208,0.521 0.25,0.25 10 false *1 3.219,1.01 3.385,1.26 0.167,0.25 10 false *a 0.49,1.719 0.823,1.969 0.333,0.25 10 false *b
*1 Rear Differential Carrier Oil Seal
*a Cut Position
*b Protective Tape


Using a knife, cut off the lip of the rear differential carrier oil seal.


b.

Using a screwdriver with its tip wrapped with protective tape, pry out the rear differential carrier oil seal.

NOTICE:

Do not damage the rear differential carrier assembly.



Hide 41201C 12.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL (for LH Side)

a.

Coat the lip of a new rear differential carrier oil seal with MP grease.


b.
C408439C01
2.167,1.542 2.333,1.708 2.333,1.708 2.5,1.708 false 0.333,1.917 0.833,1.917 false 0.479,1.917 0.479,2.667 0.479,2.667 0.729,2.667 false 2.542,1.646 2.875,1.979 0.333,0.333 10 false *1 0.031,1.854 0.448,2.104 0.417,0.25 10 false SST 3.177,1.177 3.344,1.427 0.167,0.25 10 false A
*1 Rear Differential Carrier Oil Seal


Using SST and a hammer, install the rear differential carrier oil seal.

SST
09223-46011  
09523-36010  

Standard Distance (A):

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Install the rear differential carrier oil seal uniformly.

·

Press fit the rear differential carrier oil seal straight.

·

Do not damage the rear differential carrier oil seal.

·

Do not excessively press in the rear differential carrier oil seal.

·

Make sure to install the rear differential carrier oil seal as specified, otherwise a malfunction such as an oil leak may occur.




Hide 41201C 13.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL (for RH Side)

a.

Coat the lip of a new rear differential carrier oil seal with MP grease.


b.
C408437C01
2.177,1.531 2.344,1.781 2.344,1.781 2.594,1.781 false 0.323,1.75 0.823,1.75 false 0.552,1.75 0.552,2.75 0.552,2.75 0.719,2.75 true 2.635,1.719 2.885,1.969 0.25,0.25 10 false *1 3.177,1.208 3.385,1.438 0.208,0.229 10 false A 0.031,1.688 0.615,2.021 0.583,0.333 10 false SST
*1 Rear Differential Carrier Oil Seal


Using SST and a hammer, install the rear differential carrier oil seal.

SST
09223-46011  
09523-36010  

Standard Distance (A):

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Install the rear differential carrier oil seal uniformly.

·

Press fit the rear differential carrier oil seal straight.

·

Do not damage the rear differential carrier oil seal.

·

Do not excessively press in the rear differential carrier oil seal.

·

Make sure to install the rear differential carrier oil seal as specified, otherwise a malfunction such as an oil leak may occur.




Hide 14.INSTALL ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY (for LH Side)

Hide 15.INSTALL ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 41330M 20.INSTALL TRANSMISSION COUPLING DUST SEAL

a.

Coat the lip of a new transmission coupling dust seal with MP grease.


b.
C426357C01
1.969,2.604 2.5,2.25 2.5,2.25 2.031,2.375 true 1.156,1.115 1.563,1.115 false 1.229,0.198 1.563,0.573 0.333,0.375 10 false A 2.531,2.167 2.948,2.417 0.417,0.25 10 true SST 1.604,1.042 1.844,1.26 0.24,0.219 10 false *1
*1 Transmission Coupling Dust Seal


Using SST and a hammer, install the transmission coupling dust seal to the electro magnetic control coupling sub-assembly.

SST
09316-10010  
09950-70010  (09951-07150)

Standard Distance (A):

2.0 to 2.8 mm (0.0788 to 0.1102 in.)


NOTICE:
·

Install the transmission coupling dust seal uniformly.

·

Press fit the transmission coupling dust seal straight.

·

Do not damage the transmission coupling dust seal.

·

Do not damage the No. 1 rear differential dust deflector.

·

Do not excessively press in the transmission coupling dust seal.

·

Make sure to install the transmission coupling dust seal as specified, otherwise a malfunction such as an oil leak may occur.