Home › Drivetrain › P810 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID VEHICLE TRANSAXLE › from 2020.11
RM37A0E _52 Drivetrain _086860 P810 HYBRID TRANSMISSION / TRANSAXLE _0420886 HYBRID VEHICLE TRANSAXLE A

P810 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle transaxle assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*2: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*3: If the vehicle height has changed due to suspension or tire replacement

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration DTC is output (Click here)
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for 2WD:(Click here)
for 4WD/AWD:(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front wheel alignment adjustment Perform "Calibration"
·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Replacement of front bumper assembly*2
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)
Suspension, tires, etc.*3
·

Measurement of ultrasonic sensor (rear left sensor, rear left center sensor, rear right center sensor, rear right sensor) detection angle

·

Ultrasonic sensor (rear left sensor, rear left center sensor, rear right center sensor, rear right sensor) detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD)>PRECAUTION

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PERFORM RESOLVER INITIALIZATION

NOTICE:

If it is necessary to replace the hybrid vehicle transaxle assembly, make sure to perform resolver initialization before starting work.



Hide 45319 5.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)

Hide 82121 6.DISCONNECT ENGINE WIRE

a.

for LHD, Rear side:

i.

Disconnect the wire harness connector from the rack and pinion power steering gear assembly.

C426761

HINT:

Release the lock before rotating the lock lever.



ii.

Remove the 2 bolts to disconnect the engine wire.


iii.

Disengage the 6 clamps to disconnect the engine wire.



b.

for RHD, Rear side:

i.

Disconnect the wire harness connector from the rack and pinion power steering gear assembly.

C450243

HINT:

Release the lock before rotating the lock lever.



ii.

Remove the 2 bolts to disconnect the engine wire.


iii.

Disengage the 4 clamps to disconnect the engine wire.



c.

Front side:

i.
C426763

Remove the 2 bolts to disconnect the engine wire.



Hide 821H2 7.DISCONNECT HV AIR CONDITIONING WIRE

a.
C426764

Remove the 2 bolts to disconnect the HV air conditioning wire from the hybrid vehicle transaxle assembly.


b.

Disengage the guide to disconnect the HV air conditioning wire from the hybrid vehicle transaxle assembly.


Hide 8.DISCONNECT WATER HOSE

a.
C426765

Disengage the clamp to disconnect the water hose.


Hide 33185B 9.REMOVE TRANSAXLE UNDER STOPPER BRACKET

a.
C426766

Remove the 4 bolts and transaxle under stopper bracket from the hybrid vehicle transaxle assembly.


Hide 32930G 10.REMOVE NO. 2 TRANSMISSION OIL COOLER HOSE ASSEMBLY

a.
C426903

Slide the 2 clips and disconnect the No. 2 transmission oil cooler hose assembly from the oil pump with motor assembly.


b.

Slide the clip and disconnect the No. 2 transmission oil cooler hose assembly from the motor cooling cooler.


c.

Slide the clip and disconnect the No. 2 transmission oil cooler hose assembly from the No. 1 motor cooling pipe.


d.

Disengage the hose clamp to remove the No. 2 transmission oil cooler hose assembly from the No. 2 motor cooling pipe.


Hide G1251B 11.REMOVE NO. 1 MOTOR COOLING PIPE

a.
C430780

Loosen the flare nut of the No. 1 motor cooling pipe and disconnect the No. 1 motor cooling pipe from the union.


b.

Remove the bolt, No. 2 oil cooler tube clamp and No. 1 motor cooling pipe from the No. 2 motor cooling pipe.


Hide 35300B 12.REMOVE OIL PUMP WITH MOTOR ASSEMBLY

Hide 11363A 13.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
C426767

Remove the flywheel housing side cover from the engine assembly.


Hide 51100G 14.REMOVE FRONT FRAME ASSEMBLY

Hide 12361A 15.REMOVE FRONT ENGINE MOUNTING INSULATOR

Hide 12311A 16.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
C426768

Remove the 3 bolts and front engine mounting bracket from the hybrid vehicle transaxle assembly.


Hide 12371A 17.REMOVE REAR ENGINE MOUNTING INSULATOR

Hide 12303 18.REMOVE REAR ENGINE MOUNTING BRACKET

a.
C426769

Remove the 4 bolts and rear engine mounting bracket from the hybrid vehicle transaxle assembly.


Hide 30900 19.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

a.
C426770

Remove the 8 bolts and hybrid vehicle transaxle assembly from the engine assembly.

NOTICE:
·

To avoid damaging the knock pins, do not pry between the hybrid vehicle transaxle assembly and engine assembly.

·

To prevent the splines of the transmission input damper assembly from becoming misaligned, do not allow the hybrid vehicle transaxle assembly to hit the transmission input damper assembly during hybrid vehicle transaxle assembly removal and installation.




Hide G125A 21.REMOVE MOTOR COOLING COOLER

a.
C426954

Slide the clip and disconnect the No. 1 motor cooling hose from the tube connector.


b.
C430799

Remove the 3 bolts and motor cooling cooler from the No. 1 transmission control cable bracket.


Hide G1252A 22.REMOVE NO. 2 MOTOR COOLING PIPE

a.
C426774

Remove the oil cooler union bolt and gasket to disconnect the No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.


b.

Remove the 2 bolts and No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.


Hide 33823 23.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C426776

Remove the 2 bolts and No. 1 transmission control cable bracket from the hybrid vehicle transaxle assembly.


Hide G9216 24.REMOVE NO. 3 INVERTER BRACKET

a.
C426777

Remove the 6 bolts and No. 3 inverter bracket from the hybrid vehicle transaxle assembly.


Hide 82125 25.REMOVE TRANSMISSION WIRE

a.
C426779

Disconnect the connector.


b.

Remove the bolt and transmission wire from the hybrid vehicle transaxle assembly.


Hide 26.REMOVE WIRE HARNESS CLAMP BRACKET

a.

Remove the 4 bolts and 4 wire harness clamp brackets from the hybrid vehicle transaxle assembly.

C426780


Hide 27.REMOVE TRANSAXLE HOUSING PLUG

a.
C426781

Remove the transaxle housing plug and gasket from the hybrid vehicle transaxle assembly.


Hide 28.REMOVE STUD BOLT

a.
C426782

Using a E10 "TORX" socket wrench, remove the 2 stud bolts from the hybrid vehicle transaxle assembly.


Hide 30900N 29.REMOVE TRANSAXLE BREATHER PLUG

HINT:

Perform this procedure only when replacement of the transaxle breather plug is necessary.


a.
C426783

Remove the transaxle breather plug from the hybrid vehicle transaxle assembly.


Hide 30.REMOVE TUBE CONNECTOR

HINT:

Perform this procedure only when replacement of the tube connector or O-ring is necessary.


a.
C430782

Remove the 2 tube connectors from the hybrid vehicle transaxle assembly.


b.

Remove the 2 O-rings from the 2 tube connectors.