The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during automatic transaxle assembly removal/installation are shown below.
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
| *a | An Object Exceeding Weight Limit of Transmission Jack |
The automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.
After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
If the ECM has been struck or dropped, replace it.
Perform Vehicle Identification Number (VIN) or frame number registration when replacing the ECM.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION
11361J
1.REMOVE FLYWHEEL HOUSING UNDER COVER
32101A
2.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley set bolt with a wrench.
There will be one black colored drive plate and torque converter assembly setting bolt.
52618
3.REMOVE FRONT BUMPER LOWER ABSORBER
52132A
4.REMOVE NO. 2 FRONT BUMPER REINFORCEMENT
5.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
28100
6.REMOVE STARTER ASSEMBLY
82121
7.DISCONNECT ENGINE WIRE
| *a | Park/Neutral Position Switch Assembly Connector |
| *b | Transmission Wire Connector |
Disconnect the park/neutral position switch assembly connector.
Disengage the claw, rotate the lever and disconnect the transmission wire connector.
Remove the 5 bolts and disengage the 3 clamps to disconnect the engine wire from the automatic transaxle assembly.
8.DISCONNECT VACUUM HOSE
Disengage the clamp to disconnect the vacuum hose from the engine mounting insulator LH.
35104V
9.SEPARATE BREATHER PLUG HOSE
Disengage the 4 hose clamps to separate the breather plug hose.
33197C
10.REMOVE TRANSMISSION BREATHER CLAMP
16260
11.DISCONNECT WATER BY-PASS HOSE ASSEMBLY
12.DISCONNECT HOSE CLAMP
Disengage the clamp to disconnect the hose clamp from the wire harness clamp bracket.
13.INSTALL ENGINE HANGERS
51100G
14.REMOVE FRONT FRAME ASSEMBLY
17118
15.REMOVE MANIFOLD STAY
30500
16.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY
Support the automatic transaxle assembly with a transmission jack.
Secure the automatic transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.
Remove the 11 bolts and automatic transaxle assembly from the engine assembly.
To prevent damage to the 2 knock pins, do not pry between the automatic transaxle assembly and engine assembly.
17.DISCONNECT INLET NO. 2 OIL COOLER HOSE
18.DISCONNECT OUTLET NO. 3 OIL COOLER HOSE
33493A
19.REMOVE TRANSMISSION OIL COOLER
32907C
20.REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE
12311A
21.REMOVE FRONT ENGINE MOUNTING BRACKET
Remove the 3 bolts and front engine mounting bracket from the automatic transaxle assembly.
12372A
22.REMOVE ENGINE MOUNTING INSULATOR LH
Remove the 5 bolts and engine mounting insulator LH from the automatic transaxle assembly.
12303
23.REMOVE REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY
Remove the bolt and wire harness clamp bracket from the rear engine mounting bracket sub-assembly.
Remove the 4 bolts and rear engine mounting bracket sub-assembly from the automatic transaxle assembly.
24.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle assembly.
35150
25.REMOVE TRANSMISSION CASE PLUG ASSEMBLY
Remove the transmission case plug assembly from the automatic transaxle assembly.
26.REMOVE WIRE HARNESS CLAMP BRACKET
Remove the bolt and wire harness clamp bracket from the automatic transaxle assembly.
Remove the 2 bolts and 2 wire harness clamp brackets from the automatic transaxle assembly.
35104V
27.REMOVE BREATHER PLUG HOSE
Using a screwdriver, remove the breather plug hose from the No. 1 breather plug (ATM).
Be careful not to damage the No. 1 breather plug (ATM).
| *1 | Breather Plug Sub-assembly |
| *2 | Breather Plug Hose |
Remove the breather plug sub-assembly from the breather plug hose.
Be careful not to damage the breather plug sub-assembly.
35151A
28.REMOVE UPPER TRANSAXLE CASE COVER
Disengage the 2 clips and remove the upper transaxle case cover from the automatic transaxle assembly.
29.REMOVE TORQUE CONVERTER ASSEMBLY
Remove the torque converter assembly from the automatic transaxle assembly.
30.INSPECT TORQUE CONVERTER ASSEMBLY
32101
31.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY