Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  C00409E  Brake Pedal Switch "A" Stuck On  C00409F  Brake Pedal Switch "A" Stuck Off  


DESCRIPTION

The brake pedal load sensing switch (brake pedal support assembly) signal turns on when the brake pedal is depressed with a force exceeding a predetermined level.

The skid control ECU (brake actuator assembly) uses this circuit to detect if the brake pedal is depressed or not.

DTC No. Detection Item DTC Detection Condition Trouble Area
C00409E Brake Pedal Switch "A" Stuck On Either of the following is detected:
·

When the +BS terminal voltage is 9.5 V or higher with the stop light switch signal off, the brake pedal load sensing switch (brake pedal support assembly) signal on, the master cylinder pressure below 0.7 MPa (71.1 kgf/cm2, 101 psi), and the engine speed 500 rpm or higher, the deceleration is below 0.08 G for 10 seconds or more.

·

When the +BS terminal voltage is 9.5 V or higher, the condition that the brake pedal load sensing switch (brake pedal support assembly) signal remains on while the vehicle speed increases from 0 km/h (0 mph) to 30 km/h (19 mph) occurs 5 times in succession.


·

Brake pedal load sensing switch (brake pedal support assembly)

·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)


C00409F Brake Pedal Switch "A" Stuck Off Either of the following is detected:
·

When the +BS terminal voltage is from 9.5 to 17.4 V with the stop light switch signal on, the brake pedal load sensing switch (brake pedal support assembly) signal off, and the master cylinder pressure 6 MPa (61.2 kgf/cm2, 870 psi) or more, the deceleration is 0.4 G or more for 1 second or more.

·

When the +BS terminal voltage is from 9.5 to 17.4 V with the stop light switch signal on, the brake pedal load sensing switch (brake pedal support assembly) signal off, and the master cylinder pressure exceeding 6 MPa (61.2 kgf/cm2, 870 psi), the vehicle speed is 0 km/h (0 mph) for 5 seconds or more.


·

Brake pedal load sensing switch (brake pedal support assembly)

·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY


HINT:

When P057111 and/or P057113 is output together with C00409E and/or C00409F, inspect and repair the trouble areas indicated by P057111 and/or P057113 first.

for P057111: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>P057111

for P057113: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>P057113


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SW AND BRAKE PEDAL LOAD SENSING SW)
a.

Check that the stop light switch display and brake pedal load sensing switch (brake pedal support assembly) display observed on the GTS change according to brake pedal operation.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly status
(STP or STP2 terminal input)
OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:
·

Stop light control relay off: STP terminal status displayed.

·

Stop light control relay on: STP2 terminal status displayed.



Brake Pedal Load Sensing SW Brake pedal load sensing switch (brake pedal support assembly) OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
-
Chassis > Brake/EPB > Data List
Tester Display
Stop Light SW
Brake Pedal Load Sensing SW
50003 435 59,61
OK:

The GTS displays OFF / ON according to brake pedal operation.



b.

Slowly depress the brake pedal, and check when the stop light switch assembly and brake pedal load sensing switch (brake pedal support assembly) turn on.

OK:

First the stop light switch assembly should turn on, and then the brake pedal load sensing switch (brake pedal support assembly) should turn on.



Result:
Result Proceed to
OK A
NG (Turning on of the brake pedal load sensing switch (brake pedal support assembly) is not confirmed.) B
NG (The brake pedal load sensing switch (brake pedal support assembly) turns on first.) C



A

2.CLEAR DTC

B

4.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY

C

6.CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTC C00409E and C00409F are not output. A
DTC C00409E and/or C00409F are output. B



A

B

4.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY
a.

Turn the ignition switch off.


b.

Inspect the brake pedal load sensing switch (brake pedal support assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL LOAD SENSING SWITCH>ON-VEHICLE INSPECTION

OK:

The brake pedal load sensing switch (brake pedal support assembly) is normal.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE PEDAL SUPPORT ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE PEDAL SUPPORT ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-2 (FSW+) - A39-28 (FSW+) Always Below 1 Ω
A45-2 (FSW+) or A39-28 (FSW+) - Body ground Always 10 kΩ or higher
A45-1 (FSW-) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch assembly installation.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for Gasoline Model LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for Gasoline Model RHD)>ADJUSTMENT

OK:

The brake pedal height and stop light switch assembly installation are normal.



Result:
Proceed to
OK
NG



OK

NG

ADJUST BRAKE PEDAL HEIGHT OR STOP LIGHT SWITCH ASSEMBLY INSTALLATION