ENGINE ASSEMBLY > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE HOOD SUB-ASSEMBLY |
Disconnect the washer nozzle hose.
Remove the 4 bolts and hood.
| 3. REMOVE NO. 1 ENGINE UNDER COVER |
| 4. REMOVE NO. 2 ENGINE UNDER COVER |
| 5. DRAIN ENGINE OIL |
Remove the oil filler cap.
Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.
Wipe the oil pan and drain plug.
Install a new gasket and the oil pan drain plug.
| 6. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.
![]() |
Drain the coolant by removing the radiator reservoir cap and, using a wrench, remove the vent plug.
Loosen the cylinder block drain cock plug.

| *1 | Radiator Reservoir | *2 | Radiator Reservoir Cap |
| *3 | Vent Plug | *4 | Cylinder Block Drain Cock Plug |
| *5 | Radiator Drain Cock Plug | - | - |
| 7. DRAIN MANUAL TRANSMISSION OIL (for Manual Transmission) |
Remove the drain plug and gasket to drain the oil.
Install a new gasket and the drain plug.
| 8. DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission) |
Remove the drain plug and gasket, and drain ATF.
Install a new gasket and the drain plug.
| 9. DRAIN POWER STEERING FLUID |
| 10. REMOVE BATTERY CLAMP SUB-ASSEMBLY |
Remove the bolt, nut and battery clamp.
| 11. REMOVE BATTERY |
| 12. REMOVE BATTERY TRAY |
| 13. REMOVE AIR CLEANER ASSEMBLY |
Disconnect the mass air flow meter connector.
Loosen the hose clamp.
Remove the 2 bolts and air cleaner.
| 14. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY |
![]() |
Remove the 3 bolts, 2 cap nuts and No. 1 engine cover.
![]() | Cap Nut |
| 15. REMOVE INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR |
| 16. REMOVE RADIATOR ASSEMBLY |
| 17. REMOVE STARTER ASSEMBLY |
| 18. REMOVE FRONT EXHAUST PIPE ASSEMBLY |
| 19. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
| 20. DISCONNECT HEATER HOSE |
![]() |
Disconnect the 2 heater hoses.
| 21. DISCONNECT PRESSURE FEED TUBE ASSEMBLY |
![]() |
Disconnect the oil reservoir to pump hose.
![]() |
Disconnect the pressure feed tube.
| 22. DISCONNECT FUEL HOSE |
![]() |
Disconnect the 2 fuel hoses.
| 23. DISCONNECT UNION TO CONNECTOR TUBE HOSE |
![]() |
Disconnect the union to connector tube hose.
| 24. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.
| *1 | Stopper |
![]() |
Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
| *1 | Hinge |
| 25. DISCONNECT WIRE HARNESS |
![]() |
Remove the upper relay block cover.
Remove the side relay block cover.
Remove the nut and disconnect the engine room junction block wire.
Disconnect the 2 engine room junction block connectors.
Remove the bolt and disconnect the ground cable.
![]() |
Remove the 2 nuts, detach the clamp and disconnect the wire harness.
![]() |
Disconnect the 3 injector driver connectors.
![]() |
Disconnect the turbo motor driver connector.
for Automatic Transmission:
Disconnect the 3 TCM connectors.
Disconnect the 4 ECM connectors.
| 26. DISCONNECT COOLER COMPRESSOR ASSEMBLY |
Remove the 4 bolts and disconnect the cooler compressor.
| 27. REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission) |
| 28. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for Automatic Transmission) |
| 29. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission) |
| 30. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR |
Remove the 4 bolts and rear No. 1 engine mounting insulator.
| 31. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission) |
![]() |
Place matchmarks on the clutch cover and flywheel.
Loosen each set bolt one turn at a time until spring tension is released.
Remove the 6 set bolts and pull off the clutch cover.
| 32. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission) |
| 33. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission) |
![]() |
Using SST, hold the crankshaft pulley.
![]() |
Remove the 8 bolts and flywheel.
| 34. REMOVE PUMP IMPELLER DRIVE PLATE (for Automatic Transmission) |
![]() |
Using SST, hold the crankshaft pulley.
![]() |
Remove the 8 bolts, the rear drive plate spacer, the pump impeller drive plate, and the flywheel.
| 35. REMOVE REAR END PLATE |
Remove the bolt and rear end plate.
| 36. INSTALL ENGINE HANGERS |
![]() |
Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
| No. 1 Engine Hanger | 12284-30060 or 12284-30070 |
| No. 2 Engine Hanger | 12282-67030 |
| Bolt | 91552-81014 and 91642-81030 |
| 37. REMOVE ENGINE ASSEMBLY |
![]() |
Attach an engine sling device and hang the engine with a chain block.
Remove the 4 bolts and 4 nuts.
Remove the engine by operating the engine sling device and chain block.
| 38. INSTALL ENGINE TO ENGINE STAND |
Install the engine to an engine stand with the bolts.
Remove the 2 bolts and 2 engine hangers.
| 39. REMOVE ENGINE WIRE |
Remove the engine wire from the engine.
| 40. REMOVE FRONT ENGINE MOUNTING INSULATOR |
![]() |
Remove the 2 nuts and 2 front engine mounting insulators.
| *A | RH Side |
| *B | LH Side |
| 41. REMOVE NO. 1 TIMING BELT COVER |
![]() |
Remove the 6 bolts, 6 washers and timing belt cover.
| 42. REMOVE TIMING BELT |
![]() |
Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
| *1 | Timing Mark |
![]() |
Uniformly loosen and remove the 2 bolts and No. 1 timing belt tensioner.
Remove the timing belt.
![]() |
| 43. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY |
Using a 10 mm hexagon wrench, remove the bolt, No. 1 timing belt idler and washer.
| 44. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, hold the crankshaft pulley and loosen the pulley bolt.
![]() |
Using SST, remove the pulley bolt and crankshaft pulley.
| 45. REMOVE NO. 2 INTERCOOLER SUPPORT BRACKET |
Remove the 2 bolts and No. 2 intercooler support bracket.
| 46. REMOVE NO. 1 INTERCOOLER SUPPORT BRACKET |
Remove the 2 bolts and No. 1 intercooler support bracket.
| 47. REMOVE NO. 2 IDLE PULLEY ASSEMBLY |
Remove the bolt, pulley plate, No. 2 idle pulley and spacer.
| 48. REMOVE GENERATOR ASSEMBLY |
![]() |
Remove the nut and generator wire.
Disconnect the generator connector.
Remove the 2 bolts and generator.
| 49. REMOVE GENERATOR BRACKET |
Remove the bolt and generator bracket.
| 50. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the 4 bolts and V-ribbed belt tensioner.
| 51. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET |
Remove the 4 bolts and No. 1 compressor mounting bracket.
| 52. REMOVE TURBOCHARGER SUB-ASSEMBLY |
| 53. REMOVE EXHAUST MANIFOLD |
![]() |
Remove the 8 nuts, 8 plate washers, 8 collars and exhaust manifold.
Remove the gasket.
| 54. REMOVE WATER INLET |
![]() |
Disconnect the wire harness clamp.
Remove the 3 bolts and water inlet.
Remove the bolt and wire harness clamp bracket from the water inlet.
| 55. REMOVE THERMOSTAT |
Remove the thermostat from the cylinder block.
Remove the gasket from the thermostat.
| 56. REMOVE WATER OUTLET |
![]() |
Remove the 2 bolts, water outlet and gasket.
| 57. REMOVE DIESEL THROTTLE BODY ASSEMBLY |
![]() |
Disconnect the 2 connectors.
![]() |
Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.
| 58. REMOVE INTAKE MANIFOLD |
| 59. REMOVE GLOW PLUG ASSEMBLY |
| 60. REMOVE FUEL INLET PIPE SUB-ASSEMBLY |
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
| *a | Common Rail Side |
| *b | Fuel Supply Pump Side |
| 61. REMOVE OIL FILTER SUB-ASSEMBLY |
![]() |
Using SST, remove the oil filter.
| 62. REMOVE COMMON RAIL ASSEMBLY |
Disconnect the 2 connectors.
![]() |
Remove the 2 bolts, common rail and No. 2 intake manifold insulator.
| 63. REMOVE FUEL SUPPLY PUMP ASSEMBLY |
![]() |
Disconnect the 2 fuel hoses.
![]() |
Disconnect the fuel temperature sensor connector and suction control valve connector.
![]() |
Remove the 4 bolts indicated by the arrows in the illustration.
Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.
![]() |
Remove the set nut and O-ring while holding the crankshaft pulley using SST.
![]() |
Loosen the 2 nuts.
![]() |
Using SST, disconnect the fuel supply pump from the injection gear.
Remove the 2 nuts and fuel supply pump.
Remove the O-ring.
| 64. REMOVE OIL COOLER COVER SUB-ASSEMBLY |
Disconnect the oil pressure switch connector.
Remove the 2 nuts and disconnect the No. 2 vacuum transmitting pipe from the oil cooler cover.
![]() |
Remove the 13 bolts, oil cooler cover and gasket.
| 65. REMOVE VACUUM PUMP ASSEMBLY |
![]() |
Remove the 2 nuts, vacuum pump and 2 O-rings.
| 66. REMOVE VANE PUMP ASSEMBLY |
![]() |
Remove the 2 nuts, vane pump and O-ring.
| 67. REMOVE CRANKSHAFT POSITION SENSOR |
Disconnect the crankshaft position sensor connector.
Detach the 4 clips and remove the bolt and crankshaft position sensor.

| 68. REMOVE CAMSHAFT POSITION SENSOR |
![]() |
Disconnect the camshaft position sensor connector.
Remove the bolt and camshaft position sensor.
| 69. REMOVE ENGINE COOLANT TEMPERATURE SENSOR |
![]() |
Disconnect the engine coolant temperature sensor connector.
Remove the engine coolant temperature sensor.
Remove the gasket from the engine coolant temperature sensor.
| 70. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH |
![]() |
Remove the 4 bolts and front No. 1 engine mounting bracket.
| *A | RH Side |
| *B | LH Side |
| 71. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH |
Remove the 4 bolts and front No. 1 engine mounting bracket.