2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag activation.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE HOOD SUB-ASSEMBLY
  1. Disconnect the washer nozzle hose.

  1. Remove the 4 bolts and hood.


3. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD and Pre-Runner)
  1. Remove the 4 bolts and No. 1 engine under cover.


4. REMOVE NO. 2 ENGINE UNDER COVER (for 4WD and Pre-Runner)
  1. Remove the 2 bolts and No. 2 engine under cover.


5. DRAIN ENGINE OIL
  1. Remove the oil filter cap.

  1. Remove the oil drain plug, and drain the engine oil from the oil pan.

    NOTICE:
    Collect the oil in an oil disposal container.


6. LOOSEN FUEL TANK CAP ASSEMBLY

7. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A099591E01
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug and the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


    A112147E01


8. REMOVE BATTERY BRACKET

9. REMOVE BATTERY AND BATTERY TRAY

10. REMOVE AIR CLEANER ASSEMBLY
  1. for Ventilation Hose Type:
    Disconnect the ventilation hose.

  1. Disconnect the mass air flow meter connector.

  1. Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner.


11. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ EGR Cooler)

  1. A135916
    Remove the 3 bolts, 2 nuts and engine cover.


12. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/o EGR Cooler)

A111785
  1. Remove the 3 bolts, 2 nuts and engine cover.


13. REMOVE INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR (w/ EGR Cooler)

  1. A149802
    Detach the 2 clamps.

  1. Disconnect the vacuum hose from the manifold absolute pressure sensor.

  1. Disconnect the IAT sensor connector and manifold absolute diesel pressure sensor connector.

  1. A149933
    Loosen the 2 hose clamps of the No. 1 air hose.

  1. A149934
    Loosen the 2 hose clamps of the No. 2 air hose.

  1. A135919
    Remove the 4 bolts and intercooler.


14. REMOVE INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR (w/o EGR Cooler)

  1. A110364
    Disconnect the vacuum hose from the manifold absolute pressure sensor.

  1. Disconnect the IAT sensor connector and manifold absolute diesel pressure sensor connector.

  1. A110365
    Loosen the 2 hose clamps of the No. 1 air hose.

  1. A110366
    Loosen the 2 hose clamps of the No. 2 air hose.

  1. A112764
    Remove the 4 bolts and CAC.


15. REMOVE RADIATOR ASSEMBLY
(Click here)

16. DISCONNECT HEATER HOSE

  1. A236415
    Disconnect the 2 heater hoses.


17. DISCONNECT PRESSURE FEED TUBE ASSEMBLY

  1. A236416
    Disconnect the oil reservoir to pump hose.

  1. A236417
    Disconnect the pressure feed tube.


18. DISCONNECT FUEL HOSE

  1. A236418
    Disconnect the 2 fuel hoses.


19. DISCONNECT UNION TO CONNECTOR TUBE HOSE

  1. A236419
    Disconnect the union to connector tube hose.


20. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

B278058E01
  1. Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.

    Text in Illustration 
    *1
    Stopper

  1. B278059E01
    Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
    Text in Illustration 
    *1
    Hinge


21. DISCONNECT WIRE HARNESS

A236420
  1. Remove the upper relay block cover.

  1. Remove the side relay block cover.

  1. Remove the nut and disconnect the engine room junction block wire.

  1. Disconnect the 2 engine room junction block connectors.

  1. Remove the bolt and disconnect the ground cable.

  1. A233020
    Remove the 2 nuts, detach the clamp and disconnect the wire harness.

  1. A238474E01
    Disconnect the 3 EDU connectors.

  1. Disconnect the 4 ECM connectors.

  1. A238642E01
    Disconnect the turbo motor driver connector.

  1. w/ A.D.D.
    Disconnect the 4WD control ECU connector.

  1. for Automatic Transmission:
    Disconnect the 3 TCM connectors.

  1. Disconnect the 4 ECU connectors.


22. DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
  1. Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.


23. REMOVE TRANSMISSION ASSEMBLY
  1. R151/R151F:
    (Click here)
  2. A340F:
    (Click here)
  3. A750F:
    (Click here)

24. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

  1. D029616E01
    Place matchmarks on the clutch cover and flywheel.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the 6 set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.


25. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

NOTICE:
Keep the lining part of the clutch disc, pressure plate and surface of the flywheel away from oil and foreign matter.


26. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

  1. A072851E02
    Using SST, hold the crankshaft pulley.
    SST
    09213-58014  
    09330-00021  

  1. A114803
    Remove the 8 bolts and flywheel.


27. REMOVE PUMP IMPELLER DRIVE PLATE (for Automatic Transmission)

  1. A072851E02
    Using SST, hold the crankshaft pulley.
    SST
    09213-58014  
    09330-00021  

  1. A114804
    Remove the 8 bolts, the rear drive plate spacer, the pump impeller drive plate, and the flywheel and ring gear.


28. REMOVE REAR END PLATE
  1. Remove the bolt and end plate.


29. REMOVE ENGINE ASSEMBLY

  1. A224109E02
    Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.

    HINT:
    Part No.
    No. 1 Engine hanger
    w/ EGR Cooler
    12284-30060
    Bolt (91552-81014)
    w/o EGR Cooler
    12284-30020
    Bolt (91552-81014)
    No. 2 Engine hanger
    12282-67030
    Bolt (91642-81030)

    Torque:
    for No. 1 engine hanger:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    for No. 2 engine hanger:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

    NOTICE:
    Install the engine hangers with new bolts.

  1. Attach an engine sling device and hang the engine with a chain block.

  1. A148168
    Remove the bolt and No. 2 cylinder block insulator.

  1. A098988E01
    Remove the 4 bolts and 4 nuts.

  1. Remove the engine by operating the engine sling device and chain block.


30. FIX ENGINE ON ENGINE STAND

31. REMOVE ENGINE WIRE
  1. Remove the engine wire.


32. REMOVE NO. 1 TIMING BELT COVER

A015094E01
  1. Remove the bolt and water hose clamp.

  1. Remove the wire harness clamp.

  1. Remove the 6 bolts and timing belt cover.


33. REMOVE TIMING BELT
(Click here)

34. REMOVE CRANKSHAFT PULLEY

  1. A072413E02
    Using SST, remove the pulley bolt.
    SST
    09213-58014  
    09330-00021  

  1. A072414E02
    Using SST, remove the pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply oil or grease to the threads and tip of SST (center bolt) before using it.


35. REMOVE TURBOCHARGER SUB-ASSEMBLY (w/ EGR Cooler)
(Click here)

36. REMOVE TURBOCHARGER SUB-ASSEMBLY (w/o EGR Cooler)
(Click here)

37. REMOVE EXHAUST MANIFOLD

  1. A152664
    Remove the 8 nuts and exhaust manifold.


38. INSPECT EXHAUST MANIFOLD

A098949E01
  1. Using a precision straightedge and feeler gauge, measure the surface contacting the cylinder head for warpage.

    Maximum warpage:
    0.40 mm (0.0157 in.)

    If the warpage is more than the maximum, replace the exhaust manifold.


39. REMOVE GENERATOR ASSEMBLY

A111821
  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.


40. REMOVE GENERATOR BRACKET
  1. Remove the bolt and generator bracket.


41. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

A098937E01
  1. Remove the 4 bolts and V-ribbed belt tensioner.


42. REMOVE INTERCOOLER SUPPORT BRACKET
  1. Remove the 2 bolts and intercooler support bracket.


43. REMOVE NO. 2 INTERCOOLER SUPPORT BRACKET
  1. Remove the 2 bolts and No. 2 intercooler support bracket.


44. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
  1. Remove the 4 bolts and No. 1 compressor mounting bracket.


45. REMOVE WATER INLET

A097637E01
  1. Remove the 3 bolts and water inlet.


46. REMOVE THERMOSTAT

47. REMOVE WATER OUTLET

  1. A149947E01
    Remove the 2 bolts and water outlet.


48. REMOVE GLOW PLUG ASSEMBLY
  1. w/ EGR Cooler:
    (Click here)
  2. w/o EGR Cooler:
    (Click here)

49. REMOVE OIL FILTER SUB-ASSEMBLY

B011502E01
  1. Using SST, remove the oil filter.

    SST
    09228-07501  

    HINT:
    Insert the drain hose in the oil filter. Put the drain oil container beneath the drain hose to collect the oil from the oil filter.


50. REMOVE INTAKE MANIFOLD
  1. w/ EGR Cooler:
    (Click here)
  2. w/ EGR system without EGR Cooler:
    (Click here)
  3. w/o EGR System:
    (Click here)

51. INSPECT INTAKE MANIFOLD

A098945E01
  1. Using a precision straightedge and feeler gauge, measure the surface contacting the cylinder head for warpage.

    Maximum warpage:
    0.40 mm (0.0157 in.)

    If the warpage is more than the maximum, replace the intake manifold.


52. REMOVE FUEL SUPPLY PUMP ASSEMBLY

G036615E01
  1. Remove the bolt and clamp.

  1. Remove the 2 bolts and oil level gauge guide.

  1. A098969E05
    Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.

  1. A098895E01
    Disconnect the 2 fuel hoses.

  1. A098896E01
    Disconnect the 2 connectors.

  1. A070710E01
    Remove the 4 bolts indicated by the arrows in the illustration.

  1. Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.

  1. A070711E02
    Remove the set nut and O-ring while holding the crankshaft pulley by using SST.
    SST
    09213-58013  
    09330-00021  

  1. A098897E01
    Loosen the 2 nuts.

  1. A070714E01
    Using SST, disconnect the pump from the injection gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply lubricant to the threads and tip of SST (center bolt) before using it.

  1. Remove the 2 nuts and pump.

    NOTICE:
    1. Do not hold the pump or carry it holding the pipe.
    2. The pump must be kept horizontal.

  1. Remove the O-ring.


53. REMOVE COMMON RAIL ASSEMBLY
  1. Disconnect the 2 connectors.

  1. A231856
    Remove the 2 bolts, common rail and No. 2 intake manifold insulator.

    NOTICE:
    Do not remove the pressure discharge valve and fuel pressure sensor.


54. REMOVE OIL COOLER COVER SUB-ASSEMBLY

A151174
  1. Disconnect the oil pressure switch connector and wire harness.

  1. Remove the 2 nuts and No. 2 vacuum transmitting pipe.

  1. Remove the 13 bolts and oil cooler cover.


55. REMOVE TIMING GEAR COVER INSULATOR (w/ EGR Cooler)

  1. A148171
    Remove the bolt and timing gear cover insulator.


56. REMOVE VACUUM PUMP ASSEMBLY

  1. A098930E01
    Remove the 2 nuts, vacuum pump and 2 O-rings.


57. REMOVE VANE PUMP ASSEMBLY

  1. A233594
    Remove the 2 nuts, vane pump and O-ring.


58. REMOVE CRANKSHAFT POSITION SENSOR
  1. Remove the bolt and crankshaft position sensor.


59. REMOVE CAMSHAFT POSITION SENSOR
  1. Remove the bolt and camshaft position sensor.


60. REMOVE ENGINE COOLANT TEMPERATURE SENSOR
  1. Using a 19 mm deep socket wrench, remove the engine coolant temperature sensor and gasket.


61. REMOVE FRONT ENGINE MOUNTING INSULATOR
  1. Remove the 2 nuts and 2 front engine mounting insulators.


62. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET RH

  1. A233593E01
    Remove the 4 bolts and No. 1 front engine mounting bracket.


63. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET LH
  1. Remove the 4 bolts and No. 1 front engine mounting bracket.

← COMPONENTS (from Aug 2012)REMOVAL (Aug 2012 – Jul 2013) →