C1407 Open or Short in Rear Speed Sensor RH Circuit
Diagnostic trouble codes · Vehicles built Jun 2011 – Oct 2011
Also covers:
- C1408 Open or Short in Rear Speed Sensor LH Circuit
Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Refer to DTCs C1401 and C1402 (Click here).| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1407 C1408 |
Either condition is met:
|
|
- HINT:
- DTC C1407 is for the rear speed sensor RH.
- DTC C1408 is for the rear speed sensor LH.
- DTC C1407 is for the rear speed sensor RH.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the brake actuator assembly, perform calibration (Click here).
- Check the speed sensor signal after replacement (Click here).
- Before disconnecting the connector, make sure that there are no problems with the connection.
- After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
- After replacing the brake actuator assembly, perform calibration (Click here).
| 1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Speed Open
Rear speed sensor RH open circuit detection / Error or Normal
Normal
-
RL Speed Open
Rear speed sensor LH open circuit detection / Error or Normal
Normal
-
- OK:
- Normal (there are no momentary interruptions).
- HINT:
- Perform the above inspection before removing the sensor or disconnecting a connector.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Wheel Speed
Rear speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
RL Wheel Speed
Rear speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
Check the speed value output from the speed sensor displayed on the intelligent tester.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
|
|
||||
| OK | |
| 3. RECONFIRM DTC |
Clear the DTC (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
for LHD
B
for RHD
C
- HINT:
- If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area (Click here).
|
|
||||
|
|
||||
| A | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the speed sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RH Tester Connection
Condition
Specified Condition
S35-17 (RR+) - S41-2
Always
Below 1 Ω
S35-17 (RR+) - Body ground
Always
10 kΩ or higher
S35-16 (RR-) - S41-1
Always
Below 1 Ω
S35-16 (RR-) - Body ground
Always
10 kΩ or higher
for LH Tester Connection
Condition
Specified Condition
S35-5 (RL+) - S40-2
Always
Below 1 Ω
S35-5 (RL+) - Body ground
Always
10 kΩ or higher
S35-4 (RL-) - S40-1
Always
Below 1 Ω
S35-4 (RL-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK TERMINAL VOLTAGE (SENSOR POWER SUPPLY VOLTAGE TERMINAL) |
Turn the ignition switch off.
Connect the skid control ECU (brake actuator assembly) connector.
Disconnect the speed sensor connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
for RH Tester Connection
Switch Condition
Specified Condition
S41-2 - Body ground
Ignition switch ON
8 to 14 V
for LH Tester Connection
Switch Condition
Specified Condition
S40-2 - Body ground
Ignition switch ON
8 to 14 V
Text in Illustration *A
for RH
*B
for LH
*a
Front view of wire harness connector
(to Rear Speed Sensor)
Result Result
Proceed to
OK
A
NG
for LHD
B
for RHD
C
|
|
||||
|
|
||||
| A | ||
| ||
