2014 Hilux · Service Manual BRAKE

C1403 Rear Speed Sensor RH Malfunction

Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

Refer to DTCs C1401 and C1402 (Click here).
DTC Code
DTC Detection Condition
Trouble Area
C1403
C1404
One of the following conditions is met:
  1. At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is below that of the other sensors for 15 seconds or more.
  2. At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.
  3. At a vehicle speed of less than 10 km/h (6 mph), the outputs from both rear speed sensors are 0 km/h (0 mph) for a cumulative time of 200 seconds.
  1. Rear speed sensor RH/LH
  2. Rear skid control rotor RH/LH
  3. Sensor installation
C1273
C1274
Stored during Test Mode.
  1. Rear speed sensor RH/LH
  2. Rear skid control rotor RH/LH
  3. Sensor installation

HINT:
  1. DTCs C1403 and C1273 are for the rear speed sensor RH.
  2. DTCs C1404 and C1274 are for the rear speed sensor LH.


INSPECTION PROCEDURE

NOTICE:
Check the speed sensor signal after cleaning or replacement (Click here).


1. CHECK REAR SPEED SENSOR INSTALLATION
  1. Turn the ignition switch off.

  1. C108871E11
    Check the speed sensor installation (Click here).
    Text in Illustration 
    *1
    Rear Speed Sensor
    *a
    No clearance
    *b
    CORRECT
    *c
    INCORRECT

    OK:
    The installation bolt is tightened properly.
    There is no clearance between the sensor and rear axle housing.



NG
INSTALL REAR SPEED SENSOR CORRECTLY
OK


2. INSPECT REAR SPEED SENSOR TIP
  1. Turn the ignition switch off.

  1. Remove the rear speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil or foreign matter on the sensor tip.

    NOTICE:
    Do not replace the speed sensor if no damage to the speed sensor tip is found.

    HINT:
    1. If the sensor is contaminated with oil or other foreign material, clean the sensor.
    2. If there is iron powder sticking to the rotor, this will result in a malfunction. Therefore, confirm that the rotor is not contaminated with foreign material before replacing the sensor.



NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


3. INSPECT REAR SKID CONTROL ROTOR
  1. Turn the ignition switch off.

  1. Remove the rear axle shaft with backing plate (Click here).

  1. Check the rear skid control rotor.

    OK:
    No scratches, oil or foreign matter on the rotor.



NG
CLEAN OR REPLACE REAR SKID CONTROL ROTOR
OK


4. READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    Rear speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.
    RL Wheel Speed
    Rear speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.

  1. Check the speed value output from the speed sensor displayed on the intelligent tester.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)

5. REPLACE REAR SPEED SENSOR
  1. Turn the ignition switch off.

  1. Replace the rear speed sensor (Click here).


NEXT


6. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPLACE REAR SKID CONTROL ROTOR (Click here)
A

END


← C1403 Rear Speed Sensor RH Malfunction (+ C1273, C1274, C1404) (Jun 2011 – Jul 2012)C1403 Rear Speed Sensor RH Malfunction (+ C1273, C1274, C1404) (from Aug 2013) →