2014 Hilux · Service Manual BRAKE

C1415 Rear Speed Sensor RH Output Malfunction

Diagnostic trouble codes · Vehicles built Apr 2012 – Jul 2012

Also covers:

Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTCs C1401 and C1402 (Click here).
DTC Code
DTC Detection Condition
Trouble Area
C1415
C1416
One of the following conditions is met:
  1. An open in the sensor signal circuit occurs 255 times or more.
  2. At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals 75 times or more within 5 seconds.
  3. At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.
  1. Rear speed sensor RH/LH
  2. Speed sensor circuit
  3. Rear skid control rotor RH/LH
  4. Skid control ECU (Brake actuator assembly)
C1277
C1278
Stored during Test Mode.
  1. Rear speed sensor RH/LH
  2. Rear skid control rotor RH/LH

HINT:
  1. DTCs C1415 and C1277 are for the rear speed sensor RH.
  2. DTCs C1416 and C1278 are for the rear speed sensor LH.


WIRING DIAGRAM

Refer to DTCs C1407 and C1408 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (Click here).
  2. Check the speed sensor signal after replacement (Click here).
  3. Before disconnecting the connector, make sure that there are no problems with the connection.
  4. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Speed Open
    Rear speed sensor RH open circuit detection / Error or Normal
    Normal
    -
    RL Speed Open
    Rear speed sensor LH open circuit detection / Error or Normal
    Normal
    -

    OK:
    Normal (there are no momentary interruptions).

    HINT:
    Perform the above inspection before removing the sensor or disconnecting a connector.



NG
Go to step 8
OK


2. READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    Rear speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.
    RL Wheel Speed
    Rear speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.

  1. Check the speed value output from the speed sensor displayed on the intelligent tester.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 5
OK


3. PERFORM TEST MODE (SIGNAL CHECK)
  1. Perform the signal check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are cleared.



NG
Go to step 5
OK


4. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    for LHD
    B
    for RHD
    C

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

5. CHECK REAR SPEED SENSOR INSTALLATION
  1. Turn the ignition switch off.

  1. C108871E11
    Check the speed sensor installation (Click here).
    Text in Illustration 
    *1
    Rear Speed Sensor
    *a
    No clearance
    *b
    CORRECT
    *c
    INCORRECT

    OK:
    The installation bolt is tightened properly.
    There is no clearance between the sensor and rear axle housing.



NG
INSTALL REAR SPEED SENSOR CORRECTLY
OK


6. INSPECT REAR SPEED SENSOR TIP
  1. Turn the ignition switch off.

  1. Remove the rear speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil or foreign matter on the sensor tip.

    NOTICE:
    Do not replace the speed sensor if no damage to the speed sensor tip is found.

    HINT:
    1. If the sensor is contaminated with oil or other foreign material, clean the sensor.
    2. If there is iron powder sticking to the rotor, this will result in a malfunction. Therefore, confirm that the rotor is not contaminated with foreign material before replacing the sensor.



NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


7. INSPECT REAR SKID CONTROL ROTOR
  1. Turn the ignition switch off.

  1. Remove the rear axle shaft with backing plate (Click here).

  1. Check the rear skid control rotor.

    OK:
    No scratches, oil or foreign matter on the rotor.



NG
CLEAN OR REPLACE REAR SKID CONTROL ROTOR
OK


8. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    S35-17 (RR+) - S41-2
    Always
    Below 1 Ω
    S35-17 (RR+) - Body ground
    Always
    10 kΩ or higher
    S35-16 (RR-) - S41-1
    Always
    Below 1 Ω
    S35-16 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH 
    Tester Connection
    Condition
    Specified Condition
    S35-5 (RL+) - S40-2
    Always
    Below 1 Ω
    S35-5 (RL+) - Body ground
    Always
    10 kΩ or higher
    S35-4 (RL-) - S40-1
    Always
    Below 1 Ω
    S35-4 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK TERMINAL VOLTAGE (SENSOR POWER SUPPLY VOLTAGE TERMINAL)
  1. Turn the ignition switch off.

  1. Connect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the speed sensor connector.

  1. C238771E03
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH 
    Tester Connection
    Switch Condition
    Specified Condition
    S41-2 - Body ground
    Ignition switch ON
    8 to 14 V
    for LH 
    Tester Connection
    Switch Condition
    Specified Condition
    S40-2 - Body ground
    Ignition switch ON
    8 to 14 V

    Text in Illustration 
    *A
    for RH
    *B
    for LH
    *a
    Front view of wire harness connector
    (to Rear Speed Sensor)
    Result 
    Result
    Proceed to
    OK
    A
    NG
    for LHD
    B
    for RHD
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A


10. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
Go to step 11
A

USE SIMULATION METHOD TO CHECK (Click here)

11. REPLACE REAR SPEED SENSOR
  1. Turn the ignition switch off.

  1. Replace the rear speed sensor (Click here).


NEXT


12. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPLACE REAR SKID CONTROL ROTOR (Click here)
A

END


← C1415 Rear Speed Sensor RH Output Malfunction (+ C1277, C1278, C1416) (Nov 2011 – Mar 2012)C1415 Rear Speed Sensor RH Output Malfunction (+ C1277, C1278, C1416) (Aug 2012 – Jul 2013) →