When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
After removing the injection pipes, clean them with a brush and compressed air.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
3.DRAIN ENGINE OIL
4.DRAIN ENGINE COOLANT
5.REMOVE ENGINE ASSEMBLY
6.REMOVE NO. 1 TIMING BELT COVER
7.REMOVE TIMING BELT
8.REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY
9.REMOVE NO. 2 IDLE PULLEY ASSEMBLY
10.REMOVE GENERATOR ASSEMBLY
11.REMOVE GENERATOR BRACKET
12.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
13.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
14.REMOVE DIESEL THROTTLE BODY ASSEMBLY (w/ EGR Cooler)
15.REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE (w/ EGR Cooler)
16.REMOVE MANIFOLD STAY (w/o EGR Cooler)
17.DISCONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler)
18.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler)
19.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY
20.REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler)
21.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ EGR Cooler)
22.REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ EGR Cooler)
23.REMOVE INTAKE AIR CONNECTOR (w/ EGR Cooler)
24.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler)
25.REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY
26.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
27.REMOVE FUEL INLET PIPE SUB-ASSEMBLY
28.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
29.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
30.REMOVE CAMSHAFT TIMING PULLEY
31.REMOVE NO. 2 TIMING BELT COVER
32.REMOVE WATER PUMP ASSEMBLY
33.REMOVE TIMING GEAR COVER INSULATOR (w/ EGR Cooler)
34.REMOVE VACUUM PUMP ASSEMBLY
35.REMOVE VANE PUMP ASSEMBLY
36.REMOVE CAMSHAFT POSITION SENSOR
37.REMOVE CRANKSHAFT POSITION SENSOR
38.REMOVE PUMP DRIVE SHAFT PULLEY
Remove the 4 bolts, No. 2 camshaft timing pulley flange and pump drive shaft pulley.
Using SST, hold the crankshaft pulley and remove the nut and O-ring.
39.REMOVE CRANKSHAFT PULLEY
40.REMOVE TIMING GEAR COVER
41.REMOVE INJECTION GEAR
42.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
43.REMOVE CRANKSHAFT TIMING GEAR
44.REMOVE IDLE GEAR THRUST PLATE
45.REMOVE NO. 1 IDLE GEAR
46.REMOVE NO. 1 IDLE GEAR SHAFT
47.REMOVE FUEL SUPPLY PUMP ASSEMBLY
48.REMOVE OIL PAN SUB-ASSEMBLY
49.REMOVE OIL STRAINER SUB-ASSEMBLY
50.REMOVE TIMING GEAR CASE ASSEMBLY