Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY(for Double Cab) › 2012.01–2012.04
RM1840EF _59 Vehicle Exterior _009652 DOOR / HATCH _0052795 FUEL LID LOCK CONTROL CABLE ASSEMBLY(for Double Cab) A

DOOR / HATCH  FUEL LID LOCK CONTROL CABLE ASSEMBLY(for Double Cab)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FUEL FILLER OPENING LID LOCK RETAINER

B277117

a.

Install the fuel filler opening lid lock retainer and turn it counterclockwise as shown in the illustration.


Hide 2.INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

B277115

a.

Install the fuel lid lock control cable and turn the fuel filler opening lid lock retainer clockwise as shown in the illustration.


b.

Attach the cable to the clamps shown in the illustration.


c.

Install the grommet to the vehicle body.


d.

Install the fuel lid lock open lever.

B278268
5.271,1.333 5.531,0.385 5.531,0.385 5.365,0.385 true 1.24,7.021 1.417,7.146 false 4.042,4.729 4.531,5.104 true 3.74,5.135 3.823,5.438 false 3.427,5 2.771,4.667 true 5.208,0.292 5.396,0.5 0.188,0.208 10 false *1 1.313,0.74 1.5,0.948 0.188,0.208 10 false *2 5.01,6 5.188,6.219 0.177,0.219 10 false C 2.76,6.01 2.938,6.229 0.177,0.219 10 false B 0.427,5.99 0.604,6.208 0.177,0.219 10 false A 1.458,7.115 1.646,7.323 0.188,0.208 10 false *2 2.604,4.573 2.781,4.792 0.177,0.219 10 false A 3.792,5.448 4.021,5.688 0.229,0.24 10 false B 4.583,5.063 4.76,5.281 0.177,0.219 10 false C
*1 Fuel Lid Lock Open Lever *2 Grommet



Hide 3.INSTALL REAR WHEEL HOUSE LINER LH

a.

Install the rear wheel house liner.


Hide 4.INSTALL REAR NO. 1 WHEEL OPENING EXTENSION SUB-ASSEMBLY LH (w/ Over Fender)

Hide 5.INSTALL FRONT FLOOR CARPET ASSEMBLY

a.

Install the floor carpet.


Hide 6.INSTALL LOWER QUARTER TRIM PANEL LH

a.

Attach the 3 clips and claw to install the lower quarter trim panel.


b.

Install the front door opening trim.


Hide 7.INSTALL LOWER CENTER PILLAR GARNISH LH

a.

Attach the 2 clips, 2 claws and 2 guides to install the lower center pillar garnish.


b.

Install the front door opening trim.


c.

Connect the front seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 9.INSTALL COWL SIDE TRIM BOARD LH

a.

Attach the 2 clips to install the cowl side trim board.


b.

Install the clip.


Hide 12.INSTALL CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 15.INSTALL FRONT SEAT ASSEMBLY RH

a.

for Manual Seat:

HINT:

Use the same procedure described for the LH side.