Home › TRANSMISSION ยท R150 / R151 MANUAL TRANSMISSION › MANUAL TRANSMISSION ASSEMBLY

MANUAL TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY


C168651E01
  1. Align the input shaft with the clutch disc and install the transmission to the engine.

  1. Install the 7 bolts.

    Torque:
    for bolt A:
    72 N*m{ 730 kgf*cm , 53 ft.*lbf }
    for bolt B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



2. INSTALL EXHAUST MANIFOLD STAY


B086194E07
  1. Install the exhaust manifold stay with the 3 bolts.

    Torque:
    for bolt A:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    for bolt B:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }
    for bolt C:
    72 N*m{ 730 kgf*cm , 53 ft.*lbf }



3. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR


G034222E03
  1. Install the mounting insulator with the 4 bolts.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }



4. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


B085193E08
  1. Install the frame crossmember with the 4 bolts and 4 nuts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf } for bolt A

  1. Install the 4 set bolts to the rear No. 1 engine mounting insulator.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf } for bolt B



5. INSTALL STARTER ASSEMBLY
for 2TR-FBE: (Click here)
for 2TR-FE 1.6 kW Type: (Click here)
for 2TR-FE 1.7 kW Type: (Click here)


6. CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY


G034217E02
  1. Install the clutch release cylinder with the 2 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }



7. CONNECT WIRE HARNESS
  1. Connect the back-up light switch connector and speedometer sensor connector.



8. INSTALL FRONT EXHAUST PIPE ASSEMBLY
for 2TR-FBE: (Click here)
for 2TR-FE: (Click here)


9. INSTALL REAR PROPELLER SHAFT ASSEMBLY
for DANA made: (Click here)
except DANA made: (Click here)


10. ADD MANUAL TRANSMISSION OIL


D025304E06

Oil grade:
GL-4

Viscosity:
SAE 75W-90

Standard capacity:
2.6 liters (2.7 US qts, 2.3 Imp. qts)

Torque:
37 N*m{ 377 kgf*cm , 27 ft.*lbf }



11. INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY
  1. Cover the shift lever cap with a cloth.

  1. Press down on the shift lever cap and rotate it clockwise to install it.

    HINT:
    Apply MP grease to the tip of the shift lever.



12. INSTALL SHIFT LEVER BOOT ASSEMBLY


G034215E07
  1. Install the shift lever boot with the 4 screws and 2 clips.



13. INSTALL CONSOLE BOX ASSEMBLY
(Click here)


14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



15. INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }



16. INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }