Home › Vehicle Interior › DOOR LOCK › DOOR CONTROL RELAY
RM33K0E _58 Vehicle Interior _043547 DOOR LOCK _0233538 DOOR CONTROL RELAY G

DOOR LOCK  DOOR CONTROL RELAY  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the door lock relay removal/installation are shown below.

Necessary Procedures After Parts Removed / Installed / Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal
w/ Power Back Door System:

Reset back door close position


Power back door system (Click here)

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

for Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55667 3.REMOVE INSTRUMENT PANEL REGISTER BEZEL GARNISH

Hide 55011A 4.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55012A 5.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55405B 6.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Hide 55522B 7.REMOVE RADIO TUNER OPENING COVER (w/o Audio)

Hide 86120 8.REMOVE RADIO RECEIVER ASSEMBLY (w/ Audio, for Radio Receiver Type)

Hide 86140A 9.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio, for Radio and Display Type)

Hide 86120L 10.REMOVE NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)

Hide 55905J 11.REMOVE CONTROL KNOB SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 84013A 12.REMOVE INTEGRATION PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55900 13.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Hide 55407C 14.REMOVE LOWER INSTRUMENT COVER SUB-ASSEMBLY

Hide 84930G 15.REMOVE DOOR LOCK CONTROL RELAY

a.
B438905C01
1.625,0.698 1.354,0.323 1.354,0.323 1.073,0.323 true 1.646,1.083 1.302,1.521 1.302,1.521 1.021,1.521 true 0.854,0.24 1.167,0.438 0.313,0.198 10 true *1 0.854,1.438 1.167,1.635 0.313,0.198 10 true *2
*1 No. 1 Door Lock Control Relay
*2 No. 2 Door Lock Control Relay


Remove the door lock control relay.


Hide 84930G 16.INSPECT NO. 1 DOOR LOCK CONTROL RELAY

a.
E256068N01
2.896,0.719 3.052,0.896 false 2.396,0.583 2.594,0.583 false 2.229,0.896 2.375,0.76 false 2.74,1.052 2.49,1.208 false 2.5,1.542 2.719,1.427 false 0.281,1.396 0.438,1.594 0.156,0.198 10 false 1 1.573,1.396 1.729,1.594 0.156,0.198 10 false 2 0.292,0.677 0.448,0.875 0.156,0.198 10 false 3 1.573,0.406 1.729,0.604 0.156,0.198 10 false 4 1.573,0.896 1.729,1.094 0.156,0.198 10 false 5 2.792,0.604 2.948,0.802 0.156,0.198 10 false 1 2.417,0.667 2.573,0.865 0.156,0.198 10 false 2 2.281,0.479 2.438,0.677 0.156,0.198 10 false 3 2.792,0.958 2.948,1.156 0.156,0.198 10 false 4 2.75,1.323 2.906,1.521 0.156,0.198 10 false 5

Inspect the No. 1 door lock control relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage is not applied to terminals 1 and 2 Below 1 Ω
Battery voltage is applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 1 door lock control relay.



Hide 84930H 17.INSPECT NO. 2 DOOR LOCK CONTROL RELAY

a.
E256068N01
2.896,0.719 3.052,0.896 false 2.396,0.583 2.594,0.583 false 2.229,0.896 2.375,0.76 false 2.74,1.052 2.49,1.208 false 2.5,1.542 2.719,1.427 false 0.281,1.396 0.438,1.594 0.156,0.198 10 false 1 1.573,1.396 1.729,1.594 0.156,0.198 10 false 2 0.292,0.677 0.448,0.875 0.156,0.198 10 false 3 1.573,0.406 1.729,0.604 0.156,0.198 10 false 4 1.573,0.896 1.729,1.094 0.156,0.198 10 false 5 2.792,0.604 2.948,0.802 0.156,0.198 10 false 1 2.417,0.667 2.573,0.865 0.156,0.198 10 false 2 2.281,0.479 2.438,0.677 0.156,0.198 10 false 3 2.792,0.958 2.948,1.156 0.156,0.198 10 false 4 2.75,1.323 2.906,1.521 0.156,0.198 10 false 5

Inspect the No. 2 door lock control relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage is not applied to terminals 1 and 2 Below 1 Ω
Battery voltage is applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 2 door lock control relay.



Hide 84930G 18.INSTALL DOOR LOCK CONTROL RELAY

a.
B438905C03
1.625,0.698 1.354,0.323 1.354,0.323 1.073,0.323 true 1.646,1.083 1.302,1.521 1.302,1.521 1.021,1.521 true 0.854,0.24 1.167,0.438 0.313,0.198 10 true *1 0.854,1.438 1.167,1.635 0.313,0.198 10 true *2
*1 No. 1 Door Lock Control Relay
*2 No. 2 Door Lock Control Relay


Install the door lock control relay.


Hide 55407C 19.INSTALL LOWER INSTRUMENT COVER SUB-ASSEMBLY

Hide 55900 20.INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Hide 84013A 21.INSTALL INTEGRATION PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55905J 22.INSTALL CONTROL KNOB SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55522B 23.INSTALL RADIO TUNER OPENING COVER (w/o Audio)

Hide 86120 24.INSTALL RADIO RECEIVER ASSEMBLY (w/ Audio, for Radio Receiver Type)

Hide 86140A 25.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio, for Radio and Display Type)

Hide 86120L 26.INSTALL NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)

Hide 55405B 27.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Hide 55011A 28.INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55012A 29.INSTALL NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55667 30.INSTALL INSTRUMENT PANEL REGISTER BEZEL GARNISH

Hide 31.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION