Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE(for 4WD and Pre-Runner) › 2015.06–2016.01
RM3250E _54 Brake _038048 PARKING BRAKE _0176663 PARKING BRAKE CABLE(for 4WD and Pre-Runner) A

PARKING BRAKE  PARKING BRAKE CABLE(for 4WD and Pre-Runner)  REMOVAL  


PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 42403 2.REMOVE REAR BRAKE DRUM SUB-ASSEMBLY

Hide 46201E 3.REMOVE PARKING BRAKE LEVER SUB-ASSEMBLY

Hide 899A0A 4.REMOVE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (w/ Smart Entry and Start System)

Hide 5.REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)

Hide 6.REMOVE FRONT SEAT ASSEMBLY (for Bench Seat Type)

Hide 7.REMOVE REAR SEAT ASSEMBLY

a.

for Smart Cab (w/ Rear Seat Assembly):

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Smart Cab)>REMOVAL


b.

for Double Cab:




Hide 64271C 8.REMOVE BACK PANEL TRIM (for Smart Cab)

Hide 67918E 11.REMOVE REAR DOOR SCUFF PLATE LH (for Double Cab)

Hide 67917C 12.REMOVE REAR DOOR SCUFF PLATE RH (for Double Cab)

Hide 73370C 13.DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

Hide 73360C 14.DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

a.

for Smart Cab:

HINT:

Use the same procedure described for the LH side.



b.

for Double Cab:

HINT:

Use the same procedure described for the LH side.



Hide 58774A 17.REMOVE LUGGAGE COMPARTMENT SIDE COVER LH (for Smart Cab)

Hide 58773A 18.REMOVE LUGGAGE COMPARTMENT SIDE COVER RH (for Smart Cab)

Hide 46334 19.REMOVE INTERMEDIATE LEVER PROTECTOR

a.

Partially remove the floor carpet.

HINT:

It is not necessary to fully remove the floor carpet. Partially remove it so that the intermediate lever protector can be removed in a later step.



b.

Remove the 3 bolts and intermediate lever protector with No. 2 console box mounting bracket.

C325028C01
0.354,0.094 0.667,0.25 0.313,0.156 10 false *A 3.688,0.094 4,0.25 0.313,0.156 10 false *B
*A for Single Cab *B except Single Cab



Hide 58996A 20.REMOVE NO. 2 CONSOLE BOX MOUNTING BRACKET

a.

Remove the 2 bolts and No. 2 console box mounting bracket from the intermediate lever protector.

C325016C01
0.833,0.167 1,0.333 0.167,0.167 10 false *A 4.417,0.167 4.583,0.333 0.167,0.167 10 false *B
*A for Single Cab *B except Single Cab



Hide 46439 21.REMOVE PARKING BRAKE CABLE HEAT INSULATOR

a.
C321838

Remove the 2 bolts and parking brake cable heat insulator.


Hide 46410 24.REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY

a.

Remove the 2 bolts (labeled A).

C321828C01
3.75,1.667 4,1.667 false 4.833,0.385 4.833,0.583 4.833,0.583 4.583,0.583 true 2.833,0.333 3.583,0.333 true 3.417,1.865 3.417,1.333 3.417,1.333 2.917,1.333 true 3.031,2.5 3.542,2.5 true 2.802,2.417 2.969,2.583 0.167,0.167 10 true *3 4.083,1.583 4.25,1.75 0.167,0.167 10 false *1 4.333,0.5 4.5,0.667 0.167,0.167 10 false *2 2.583,0.25 2.75,0.417 0.167,0.167 10 true *4 2.667,1.25 2.833,1.417 0.167,0.167 10 true *5 1.417,1.75 1.583,1.917 0.167,0.167 10 true A 0.333,2.083 0.5,2.25 0.167,0.167 10 true A 1.083,0.25 1.25,0.417 0.167,0.167 10 true B
*1 No. 1 Parking Brake Cable Assembly *2 No. 2 Parking Brake Cable Assembly
*3 No. 3 Parking Brake Cable Assembly *4 Parking Brake Equalizer Sub-assembly
*5 Cable Support Bracket - -



b.

Remove the clip and pin from the No. 3 parking brake cable assembly.


c.

Disconnect the No. 1 parking brake cable assembly from the No. 3 parking brake cable assembly.


d.

Disconnect the No. 1 parking brake cable assembly from the parking brake equalizer sub-assembly.


e.

Disconnect the No. 1 parking brake cable assembly from the cable support bracket.


f.

Remove the No. 1 parking brake cable assembly from inside the vehicle.


g.

Remove the bolt (labeled B) and cable support bracket.


Hide 46420 25.REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY

a.

Disconnect the No. 2 parking brake cable assembly from the parking brake shoe lever.

HINT:

Refer to the procedures up to the removal of the brake shoe.

Click hereBrake>BRAKE (REAR)>REAR BRAKE(for TMT Made 4WD and Pre-Runner)>DISASSEMBLY



b.
C325009

Remove the 2 bolts and disconnect the No. 2 parking brake cable assembly from the backing plate.


c.

Disconnect the No. 2 parking brake cable assembly from the parking brake equalizer sub-assembly.

C321829C01
3.083,1.333 3.083,0.667 3.083,0.667 3.333,0.667 false 1.25,2.146 1.25,2.583 1.25,2.583 0.667,2.583 true 3.417,0.583 3.583,0.75 0.167,0.167 10 false *1 0.417,2.5 0.583,2.667 0.167,0.167 10 false *2
*1 No. 2 Parking Brake Cable Assembly *2 Parking Brake Equalizer Sub-assembly



d.

Remove the 4 bolts and No. 2 parking brake cable assembly.


Hide 46304 26.REMOVE PARKING BRAKE EQUALIZER SUB-ASSEMBLY

a.
C321840

Remove the 2 bolts and parking brake equalizer sub-assembly.


Hide 46430 27.REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.

Disconnect the No. 3 parking brake cable assembly from the parking brake shoe lever.

HINT:

Refer to the procedures up to the removal of the brake shoe.

Click hereBrake>BRAKE (REAR)>REAR BRAKE(for TMT Made 4WD and Pre-Runner)>DISASSEMBLY



b.
C322544

Remove the 2 bolts and disconnect the No. 3 parking brake cable assembly from the backing plate.


c.

Remove the clip.

C321830C01
3.167,5.25 3.5,5.25 3.5,5.25 3.5,4.479 false 2.917,5.167 3.083,5.333 0.167,0.167 10 false *1
*1 No. 3 Parking Brake Cable Assembly - -



d.

Remove the 3 bolts, nut and No. 3 parking brake cable assembly.