Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › 2015.06–2016.01
RM3250E _58 Vehicle Interior _038073 HEATING / AIR CONDITIONING _0184342 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

The air conditioning amplifier assembly outputs the magnet clutch on request signal to the ECM. The ECM sends a magnet clutch on permission signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly turns the magnet clutch on based on this signal.

WIRING DIAGRAM

w/ PTC Heater:
E315708E06
5.208,3.385 5.667,3.583 0.458,0.198 10 false G77 5.219,3.552 6.792,4.01 1.573,0.458 10 false Air Conditioning Amplifier Assembly 5.417,1.604 5.875,1.802 0.458,0.198 10 false AC1 5.427,0.885 5.885,1.083 0.458,0.198 10 false ACT 5.427,2.542 5.885,2.74 0.458,0.198 10 false MGC 0.813,1.708 1.271,1.906 0.458,0.198 10 false AC1 0.813,0.979 1.271,1.177 0.458,0.198 10 false ACT 5.125,1.604 5.583,1.802 0.458,0.198 10 false 12 5.115,0.885 5.573,1.083 0.458,0.198 10 false 18 1.208,0.885 2.719,1.094 1.51,0.208 10 false 14*1, 19*2 1.208,1.594 2.719,1.802 1.51,0.208 10 false 15*1, 18*2 5.125,2.542 5.583,2.74 0.458,0.198 10 false 16 4.51,2.542 4.969,2.74 0.458,0.198 10 false 1 3.313,2.542 3.771,2.74 0.458,0.198 10 false 2 3.302,2.948 3.76,3.146 0.458,0.198 10 false 5 4.521,2.948 4.979,3.146 0.458,0.198 10 false 3 3.635,3.385 5.083,3.635 1.448,0.25 10 false A/C COMP 4.802,3.99 5.26,4.188 0.458,0.198 10 false 1 3.188,4.49 4.823,4.74 1.635,0.25 10 false Magnet Clutch Assembly 2.813,4.979 4.448,5.229 1.635,0.25 10 false C3 2.813,5.125 5.479,5.375 2.667,0.25 10 false Compressor Assembly with Magnet Clutch 0.354,2.229 2.26,2.438 1.906,0.208 10 false G86*1, G83*2 0.365,2.385 0.823,2.583 0.458,0.198 10 false ECM 0.583,2.646 2.406,2.875 1.823,0.229 10 false from HTR Relay 4.375,3.99 4.833,4.188 0.458,0.198 10 false MG+ 2.313,2.813 3.198,3.031 0.885,0.219 10 false A/C 5.958,0.74 6.417,0.938 0.458,0.198 10 false 5 V 6.229,1.406 6.688,1.604 0.458,0.198 10 false IC 0.083,5.25 2.333,5.5 2.25,0.25 10 false *1: for 1GD-FTV, 2GD-FTV 0.083,5.5 2.333,5.75 2.25,0.25 10 false *2: for 2KD-FTV

w/o PTC Heater:
E324891E01
5.927,0.76 6.385,0.958 0.458,0.198 10 false 5 V 5.417,0.885 5.875,1.083 0.458,0.198 10 false ACT 5.417,1.604 5.875,1.802 0.458,0.198 10 false AC1 5.417,2.542 5.875,2.74 0.458,0.198 10 false MGC 5.188,0.885 5.646,1.083 0.458,0.198 10 false 4 5.188,1.615 5.646,1.813 0.458,0.198 10 false 2 5.146,2.542 5.604,2.74 0.458,0.198 10 false 10 5.25,3.375 5.708,3.573 0.458,0.198 10 false G34 5.25,3.542 6.833,4.167 1.583,0.625 10 false Air Conditioning Amplifier Assembly 1.208,0.885 3.042,1.083 1.833,0.198 10 false 27*1, 24*2, 14*3, 19*4 1.219,1.604 3.052,1.802 1.833,0.198 10 false 33*1, 30*2, 15*3, 18*4 0.823,0.969 1.281,1.167 0.458,0.198 10 false ACT 0.823,1.719 1.281,1.917 0.458,0.198 10 false AC1 0.042,2.219 1.875,2.417 1.833,0.198 10 false G88*1, G46*2, G86*3, G83*4 0.063,2.375 1.896,2.573 1.833,0.198 10 false ECM 0.573,2.635 2.406,2.833 1.833,0.198 10 false from HTR Relay 2.333,2.792 3.208,2.99 0.875,0.198 10 false A/C 4.531,2.542 4.99,2.74 0.458,0.198 10 false 1 4.542,2.948 5,3.146 0.458,0.198 10 false 3 3.313,2.552 3.771,2.75 0.458,0.198 10 false 2 3.313,2.948 3.771,3.146 0.458,0.198 10 false 5 3.594,3.385 4.594,3.635 1,0.25 10 false A/C COMP 4.833,3.99 5.292,4.188 0.458,0.198 10 false 1 4.375,3.99 4.833,4.188 0.458,0.198 10 false MG+ 3.188,4.469 4.844,4.667 1.656,0.198 10 false Magnet Clutch Assembly 2.771,4.948 4.427,5.146 1.656,0.198 10 false C3 2.771,5.104 5.677,5.313 2.906,0.208 10 false Compressor Assembly with Magnet Clutch 0.083,4.583 1.74,4.781 1.656,0.198 10 false *1: for 1GR-FE 0.083,4.833 1.74,5.031 1.656,0.198 10 false *2: for 1TR-FE, 2TR-FE 0.083,5.083 1.833,5.333 1.75,0.25 10 false *3: for 1GD-FTV, 2GD-FTV 0.083,5.333 1.833,5.583 1.75,0.25 10 false *4: for 2KD-FTV

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and relays for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS (A/C SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Engine and ECT / Data List.


e.

Check the value(s) by referring to the table below.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/C Signal Magnet clutch on request signal ON or OFF ON: "A/C" switch on
OFF: "A/C" switch off
Operates with the engine idling and the blower switch on (LO level).
Powertrain > Engine and ECT > Data List
Tester Display
A/C Signal
50003 234 152
OK:

The display is as specified in normal condition.



Result:
Proceed to
OK
NG



OK

2.INSPECT MAGNET CLUTCH RELAY (A/C COMP)

NG

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECM)
2.INSPECT MAGNET CLUTCH RELAY (A/C COMP)
a.

Remove the A/C COMP relay from the No. 4 instrument panel relay block assembly.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)

NG

REPLACE MAGNET CLUTCH RELAY (A/C COMP RELAY)

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)
a.

w/ PTC Heater:

i.
B409698C04
0.167,1.063 0.667,1.313 0.5,0.25 2.573,1.896 2.24,1.896 2.24,1.896 1.875,1.292 true 0.281,1.104 0.74,1.302 0.458,0.198 10 false G77 0.063,0.031 0.521,0.229 0.458,0.198 10 false *a 2.625,1.802 3.083,2 0.458,0.198 10 false MGC
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G77-16 (MGC) - Body ground Ignition switch off Below 1 V
G77-16 (MGC) - Body ground Ignition switch ON 11 to 14 V




b.

w/o PTC Heater:

i.
E324892C01
0.573,0.854 1.073,1.104 0.5,0.25 2.156,1.76 1.823,1.76 1.823,1.76 1.573,1.177 true 0.688,0.896 1.146,1.094 0.458,0.198 10 false G34 2.198,1.677 2.656,1.875 0.458,0.198 10 false MGC 0.052,0.031 0.51,0.229 0.458,0.198 10 false *a
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G34-10 (MGC) - Body ground Ignition switch off Below 1 V
G34-10 (MGC) - Body ground Ignition switch ON 11 to 14 V




Result:
Proceed to
OK
NG



OK

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL


b.
E322922C04
1.438,0.354 1.938,0.604 0.5,0.25 1.875,1.313 2.104,2.031 2.104,2.031 2.354,2.031 true 1.563,0.396 2.177,0.594 0.615,0.198 10 false G77 2.406,1.948 3.021,2.146 0.615,0.198 10 true MGC 0.042,0.031 0.656,0.229 0.615,0.198 10 true *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


w/ PTC Heater:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G77-16 (MGC) - Body ground
·

Engine idling

·

Blower switch: LO or higher

·

"A/C" switch: On (magnet clutch on)


Below 1 V
G77-16 (MGC) - Body ground
·

Engine idling

·

Blower switch: LO or higher

·

"A/C" switch: Off or on (magnet clutch off)


11 to 14 V




c.
E324893C01
0.479,1.01 0.979,1.26 0.5,0.25 1.5,1.365 1.844,2 1.844,2 2.167,2 true 0.052,0.021 0.365,0.219 0.313,0.198 10 false *a 2.229,1.906 2.719,2.104 0.49,0.198 10 false MGC 0.594,1.042 1.083,1.24 0.49,0.198 10 false G34
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


w/o PTC Heater:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G34-10 (MGC) - Body ground
·

Engine idling

·

Blower switch: LO or higher

·

"A/C" switch: On (magnet clutch on)


Below 1 V
G34-10 (MGC) - Body ground
·

Engine idling

·

Blower switch: LO or higher

·

"A/C" switch: Off or on (magnet clutch off)


11 to 14 V




Result:
Proceed to
OK
NG



OK

5.INSPECT MAGNET CLUTCH ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECM)
6.CHECK HARNESS AND CONNECTOR (A/C COMP RELAY - COMPRESSOR ASSEMBLY WITH MAGNET CLUTCH AND BATTERY)
a.

Remove the A/C COMP relay from the No. 4 instrument panel junction block assembly.


b.

Disconnect the C3 compressor assembly with magnet clutch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - C3-1 (MG+) Always Below 1 Ω
Relay terminal 3 or C3-1 (MG+) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Relay terminal 5 - Body ground Ignition switch off Below 1 V
Relay terminal 5 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECM)
a.

w/ PTC Heater:

i.

Disconnect the G77 air conditioning amplifier assembly connector.


ii.

Disconnect the G86*1 or G83*2 ECM connector.

*1: for 1GD-FTV, 2GD-FTV

*2: for 2KD-FTV



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GD-FTV, 2GD-FTV:
Tester Connection Condition Specified Condition
G77-12 (AC1) - G86-15 (AC1) Always Below 1 Ω
G77-18 (ACT) - G86-14 (ACT) Always Below 1 Ω
G77-12 (AC1) or G86-15 (AC1) - Body ground Always 10 kΩ or higher
G77-18 (ACT) or G86-14 (ACT) - Body ground Always 10 kΩ or higher

for 2KD-FTV:
Tester Connection Condition Specified Condition
G77-12 (AC1) - G83-19 (AC1) Always Below 1 Ω
G77-18 (ACT) - G83-18 (ACT) Always Below 1 Ω
G77-12 (AC1) or G83-19 (AC1) - Body ground Always 10 kΩ or higher
G77-18 (ACT) or G83-18 (ACT) - Body ground Always 10 kΩ or higher




b.

w/o PTC Heater:

i.

Disconnect the G34 air conditioning amplifier assembly connector.


ii.

Disconnect the G88*1, G46*2, G86*3 or G83*4 ECM connector.

*1: for 1GR-FE

*2: for 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE:
Tester Connection Condition Specified Condition
G34-2 (AC1) - G88-33 (AC1) Always Below 1 Ω
G34-4 (ACT) - G88-27 (ACT) Always Below 1 Ω
G34-2 (AC1) or G88-33 (AC1) - Body ground Always 10 kΩ or higher
G34-4 (ACT) or G88-27 (ACT) - Body ground Always 10 kΩ or higher

for 2TR-FE:
Tester Connection Condition Specified Condition
G34-2 (AC1) - G46-30 (AC1) Always Below 1 Ω
G34-4 (ACT) - G46-24 (ACT) Always Below 1 Ω
G34-2 (AC1) or G46-30 (AC1) - Body ground Always 10 kΩ or higher
G34-4 (ACT) or G46-24 (ACT) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV:
Tester Connection Condition Specified Condition
G34-2 (AC1) - G86-15 (AC1) Always Below 1 Ω
G34-4 (ACT) - G86-14 (ACT) Always Below 1 Ω
G34-2 (AC1) or G86-15 (AC1) - Body ground Always 10 kΩ or higher
G34-4 (ACT) or G86-14 (ACT) - Body ground Always 10 kΩ or higher

for 1KD-FTV, 2KD-FTV:
Tester Connection Condition Specified Condition
G34-2 (AC1) - G83-18 (AC1) Always Below 1 Ω
G34-4 (ACT) - G83-19 (ACT) Always Below 1 Ω
G34-2 (AC1) or G83-18 (AC1) - Body ground Always 10 kΩ or higher
G34-4 (ACT) or G83-19 (ACT) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL


b.
E322922C05
1.49,0.365 1.99,0.615 0.5,0.25 2.406,1.313 2.656,1.729 2.656,1.729 2.906,1.729 true 1.594,0.406 2.208,0.604 0.615,0.198 10 false G77 2.948,1.646 3.406,2 0.458,0.354 10 true AC1 0.042,0.031 0.656,0.229 0.615,0.198 10 true *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


w/ PTC Heater:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G77-12 (AC1) - Body ground
·

Engine idling

·

Blower switch: LO or higher

·

"A/C" switch: On


Below 1 V
G77-12 (AC1) - Body ground
·

Engine idling

·

Blower switch on (LO level)

·

"A/C" switch: Off


11 to 14 V




c.
E324893C02
0.5,1 1,1.25 0.5,0.25 2.281,0.281 1.948,0.281 1.948,0.281 1.698,1.115 true 0.615,1.042 1.073,1.24 0.458,0.198 10 false G34 2.344,0.188 2.802,0.385 0.458,0.198 10 false AC1 0.063,0.042 0.521,0.24 0.458,0.198 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


w/o PTC Heater:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G34-2 (AC1) - Body ground
·

Engine idling

·

Blower switch: LO or higher

·

"A/C" switch: On


Below 1 V
G34-2 (AC1) - Body ground
·

Engine idling

·

Blower switch on (LO level)

·

"A/C" switch: Off


11 to 14 V




Result:
Proceed to
OK
NG



OK

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECM)
a.

w/ PTC Heater:

i.

Disconnect the G77 air conditioning amplifier assembly connector.


ii.

Disconnect the G86*1 or G83*2 ECM connector.

*1: for 1GD-FTV, 2GD-FTV

*2: for 2KD-FTV



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GD-FTV, 2GD-FTV:
Tester Connection Condition Specified Condition
G77-18 (ACT) - G86-14 (ACT) Always Below 1 Ω
G77-18 (ACT) or G86-14 (ACT) - Body ground Always 10 kΩ or higher

for 2KD-FTV:
Tester Connection Condition Specified Condition
G77-18 (ACT) - G83-19 (ACT) Always Below 1 Ω
G77-18 (ACT) or G83-19 (ACT) - Body ground Always 10 kΩ or higher




b.

w/o PTC Heater:

i.

Disconnect the G34 air conditioning amplifier assembly connector.


ii.

Disconnect the G88*1, G46*2, G86*3 or G83*4 ECM connector.

*1: for 1GR-FE

*2: for 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE:
Tester Connection Condition Specified Condition
G34-4 (ACT) - G88-27 (ACT) Always Below 1 Ω
G34-4 (ACT) or G88-27 (ACT) - Body ground Always 10 kΩ or higher

for 2TR-FE:
Tester Connection Condition Specified Condition
G34-4 (ACT) - G46-24 (ACT) Always Below 1 Ω
G34-4 (ACT) or G46-24 (ACT) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV:
Tester Connection Condition Specified Condition
G34-4 (ACT) - G86-14 (ACT) Always Below 1 Ω
G34-4 (ACT) or G86-14 (ACT) - Body ground Always 10 kΩ or higher

for 1KD-FTV, 2KD-FTV:
Tester Connection Condition Specified Condition
G34-4 (ACT) - G83-19 (ACT) Always Below 1 Ω
G34-4 (ACT) or G83-19 (ACT) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

10.CHECK ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK ECM
a.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL


b.
E322922C06
1.49,0.365 1.99,0.615 0.5,0.25 1.688,1.302 2.073,2.031 2.073,2.031 2.323,2.031 true 1.604,0.406 2.219,0.604 0.615,0.198 10 false G77 2.385,1.938 2.833,2.146 0.448,0.208 10 true ACT 0.063,0.052 0.677,0.25 0.615,0.198 10 true *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


w/ PTC Heater:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G77-18 (ACT) - Body ground
·

Engine running

·

Blower switch: LO or higher

·

"A/C" switch: Off or on (magnet clutch off)


Below 1 V
G77-18 (ACT) - Body ground
·

Engine running

·

Blower switch: LO or higher

·

"A/C" switch: On (magnet clutch on)


4.5 to 5.5 V




c.
E324893C03
0.5,1 1,1.25 0.5,0.25 1,0.333 1.25,0.333 1.25,0.333 1.49,1.094 true 0.615,1.042 1.073,1.24 0.458,0.198 10 false G34 0.698,0.25 1.156,0.448 0.458,0.198 10 false AC1 0.063,0.042 0.521,0.24 0.458,0.198 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


w/o PTC Heater:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G34-4 (ACT) - Body ground
·

Engine running

·

Blower switch: LO or higher

·

"A/C" switch: Off or on (magnet clutch off)


Below 1 V
G34-4 (ACT) - Body ground
·

Engine running

·

Blower switch: LO or higher

·

"A/C" switch: On (magnet clutch on)


4.5 to 5.5 V




Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG