The air conditioning amplifier assembly outputs the magnet clutch on request signal to the ECM. The ECM sends a magnet clutch on permission signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly turns the magnet clutch on based on this signal.
Inspect the fuses and relays for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Engine and ECT / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/C Signal | Magnet clutch on request signal | ON or OFF | ON: "A/C" switch on
OFF: "A/C" switch off |
Operates with the engine idling and the blower switch on (LO level). |
| Tester Display |
|---|
| A/C Signal |
The display is as specified in normal condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the A/C COMP relay from the No. 4 instrument panel relay block assembly.
Inspect the A/C COMP relay.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/ PTC Heater:
| *a | Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G77-16 (MGC) - Body ground | Ignition switch off | Below 1 V |
| G77-16 (MGC) - Body ground | Ignition switch ON | 11 to 14 V |
w/o PTC Heater:
| *a | Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G34-10 (MGC) - Body ground | Ignition switch off | Below 1 V |
| G34-10 (MGC) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
w/ PTC Heater:
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G77-16 (MGC) - Body ground | ·
Engine idling ·
Blower switch: LO or higher ·
"A/C" switch: On (magnet clutch on) |
Below 1 V |
| G77-16 (MGC) - Body ground | ·
Engine idling ·
Blower switch: LO or higher ·
"A/C" switch: Off or on (magnet clutch off) |
11 to 14 V |
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
w/o PTC Heater:
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G34-10 (MGC) - Body ground | ·
Engine idling ·
Blower switch: LO or higher ·
"A/C" switch: On (magnet clutch on) |
Below 1 V |
| G34-10 (MGC) - Body ground | ·
Engine idling ·
Blower switch: LO or higher ·
"A/C" switch: Off or on (magnet clutch off) |
11 to 14 V |
| Result | Proceed to |
|---|---|
| OK (w/ Magnet Clutch Assembly) | A |
| OK (w/o Magnet Clutch Assembly) | B |
| NG | C |
A
B
C
Remove the compressor assembly with magnet clutch.
for 1GD-FTV, 2GD-FTV:Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR(for 1GD-FTV, 2GD-FTV)>REMOVAL
for 1KD-FTV, 2KD-FTV:Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR(for 1KD-FTV, 2KD-FTV)>REMOVAL
Inspect the compressor assembly with magnet clutch.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GD-FTV, 2GD-FTV:Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR(for 1GD-FTV, 2GD-FTV)>REMOVAL
for 1KD-FTV, 2KD-FTV:Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR(for 1KD-FTV, 2KD-FTV)>REMOVAL
Remove the A/C COMP relay from the No. 4 instrument panel junction block assembly.
Disconnect the C3 compressor assembly with magnet clutch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 3 - C3-1 (MG+) | Always | Below 1 Ω |
| Relay terminal 3 or C3-1 (MG+) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Relay terminal 5 - Body ground | Ignition switch off | Below 1 V |
| Relay terminal 5 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/ PTC Heater:
Disconnect the G77 air conditioning amplifier assembly connector.
Disconnect the G86*1 or G83*2 ECM connector.
*1: for 1GD-FTV, 2GD-FTV
*2: for 2KD-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G77-12 (AC1) - G86-15 (AC1) | Always | Below 1 Ω |
| G77-18 (ACT) - G86-14 (ACT) | Always | Below 1 Ω |
| G77-12 (AC1) or G86-15 (AC1) - Body ground | Always | 10 kΩ or higher |
| G77-18 (ACT) or G86-14 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G77-12 (AC1) - G83-19 (AC1) | Always | Below 1 Ω |
| G77-18 (ACT) - G83-18 (ACT) | Always | Below 1 Ω |
| G77-12 (AC1) or G83-19 (AC1) - Body ground | Always | 10 kΩ or higher |
| G77-18 (ACT) or G83-18 (ACT) - Body ground | Always | 10 kΩ or higher |
w/o PTC Heater:
Disconnect the G34 air conditioning amplifier assembly connector.
except 5L-E:
Disconnect the G88*1, G46*2, G86*3 or G83*4 ECM connector.
*1: for 1GR-FE
*2: for 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV, 2KD-FTV
for 5L-E:
Disconnect the G120 and G121ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G34-2 (AC1) - G88-33 (AC1) | Always | Below 1 Ω |
| G34-4 (ACT) - G88-27 (ACT) | Always | Below 1 Ω |
| G34-2 (AC1) or G88-33 (AC1) - Body ground | Always | 10 kΩ or higher |
| G34-4 (ACT) or G88-27 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G34-2 (AC1) - G46-30 (AC1) | Always | Below 1 Ω |
| G34-4 (ACT) - G46-24 (ACT) | Always | Below 1 Ω |
| G34-2 (AC1) or G46-30 (AC1) - Body ground | Always | 10 kΩ or higher |
| G34-4 (ACT) or G46-24 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G34-2 (AC1) - G86-15 (AC1) | Always | Below 1 Ω |
| G34-4 (ACT) - G86-14 (ACT) | Always | Below 1 Ω |
| G34-2 (AC1) or G86-15 (AC1) - Body ground | Always | 10 kΩ or higher |
| G34-4 (ACT) or G86-14 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G34-2 (AC1) - G83-18 (AC1) | Always | Below 1 Ω |
| G34-4 (ACT) - G83-19 (ACT) | Always | Below 1 Ω |
| G34-2 (AC1) or G83-18 (AC1) - Body ground | Always | 10 kΩ or higher |
| G34-4 (ACT) or G83-19 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G34-2 (AC1) - G120-34 (AC1) | Always | Below 1 Ω |
| G34-4 (ACT) - G121-9 (ACT) | Always | Below 1 Ω |
| G34-2 (AC1) or G120-34 (AC1) - Body ground | Always | 10 kΩ or higher |
| G34-4 (ACT) or G121-9 (ACT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
w/ PTC Heater:
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G77-12 (AC1) - Body ground | ·
Engine idling ·
Blower switch: LO or higher ·
"A/C" switch: On |
Below 1 V |
| G77-12 (AC1) - Body ground | ·
Engine idling ·
Blower switch on (LO level) ·
"A/C" switch: Off |
11 to 14 V |
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
w/o PTC Heater:
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G34-2 (AC1) - Body ground | ·
Engine idling ·
Blower switch: LO or higher ·
"A/C" switch: On |
Below 1 V |
| G34-2 (AC1) - Body ground | ·
Engine idling ·
Blower switch on (LO level) ·
"A/C" switch: Off |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/ PTC Heater:
Disconnect the G77 air conditioning amplifier assembly connector.
Disconnect the G86*1 or G83*2 ECM connector.
*1: for 1GD-FTV, 2GD-FTV
*2: for 2KD-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G77-18 (ACT) - G86-14 (ACT) | Always | Below 1 Ω |
| G77-18 (ACT) or G86-14 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G77-18 (ACT) - G83-19 (ACT) | Always | Below 1 Ω |
| G77-18 (ACT) or G83-19 (ACT) - Body ground | Always | 10 kΩ or higher |
w/o PTC Heater:
Disconnect the G34 air conditioning amplifier assembly connector.
Disconnect the G88*1, G46*2, G86*3, G83*4 or G121*5 ECM connector.
*1: for 1GR-FE
*2: for 2TR-FE
*3: for 1GD-FTV, 2GD-FTV
*4: for 1KD-FTV, 2KD-FTV
*5: for 5L-E
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G34-4 (ACT) - G88-27 (ACT) | Always | Below 1 Ω |
| G34-4 (ACT) or G88-27 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G34-4 (ACT) - G46-24 (ACT) | Always | Below 1 Ω |
| G34-4 (ACT) or G46-24 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G34-4 (ACT) - G86-14 (ACT) | Always | Below 1 Ω |
| G34-4 (ACT) or G86-14 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G34-4 (ACT) - G83-19 (ACT) | Always | Below 1 Ω |
| G34-4 (ACT) or G83-19 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G34-4 (ACT) - G121-9 (ACT) | Always | Below 1 Ω |
| G34-4 (ACT) or G121-9 (ACT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
w/ PTC Heater:
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G77-18 (ACT) - Body ground | ·
Engine running ·
Blower switch: LO or higher ·
"A/C" switch: Off or on (magnet clutch off) |
Below 1 V |
| G77-18 (ACT) - Body ground | ·
Engine running ·
Blower switch: LO or higher ·
"A/C" switch: On (magnet clutch on) |
4.5 to 5.5 V |
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
w/o PTC Heater:
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G34-4 (ACT) - Body ground | ·
Engine running ·
Blower switch: LO or higher ·
"A/C" switch: Off or on (magnet clutch off) |
Below 1 V |
| G34-4 (ACT) - Body ground | ·
Engine running ·
Blower switch: LO or higher ·
"A/C" switch: On (magnet clutch on) |
4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG