Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2015.08–2016.01
RM3270E _57 Power Source / Network _041704 NETWORKING _0201720 CAN COMMUNICATION SYSTEM(for RHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  Short to B+ in CAN Bus Line  


DESCRIPTION

There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.

Symptom Trouble Area

*1: w/ Power Back Door System

*2: w/ Smart Entry and Start System

*3: w/ Navigation System

*4: w/ Audio and Visual System

*5: for LED Headlight

The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
·

Short between CAN bus lines and +B

·

ECM

·

Brake actuator assembly (skid control ECU)

·

Spiral with sensor cable sub-assembly (steering angle sensor)

·

Air conditioning amplifier assembly

·

Multiplex network door ECU*1

·

Airbag sensor assembly

·

Certification ECU (smart key ECU assembly)*2

·

4 wheel drive control ECU

·

Navigation receiver assembly*3

·

Radio and display receiver assembly*4

·

Headlight leveling ECU assembly*5

·

Combination meter assembly

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector

·

DLC3 CAN branch wire or connector



WIRING DIAGRAM

C334534E03
0.885,0.281 1.427,0.688 0.542,0.406 10 false CANH 1.406,0.135 1.948,0.542 0.542,0.406 10 false 13 1.427,0.667 1.969,1.073 0.542,0.406 10 false 22 0.917,0.781 1.458,1.188 0.542,0.406 10 false CANL 0.146,1.177 0.688,1.583 0.542,0.406 10 false G46 0.146,1.344 1.865,1.635 1.719,0.292 10 false Airbag Sensor Assembly 2.958,0.25 3.5,0.656 0.542,0.406 10 false G120 3.073,0.031 3.615,0.438 0.542,0.406 10 false 1 3.094,0.563 3.635,0.969 0.542,0.406 10 false 2 4.094,0.25 4.635,0.656 0.542,0.406 10 false G122 5.677,0.135 6.219,0.542 0.542,0.406 10 false 17 5.688,0.677 6.229,1.083 0.542,0.406 10 false 28 4.115,2.177 4.656,2.583 0.542,0.406 10 false G121 2.979,2.177 3.521,2.583 0.542,0.406 10 false G125 2.969,4.073 3.51,4.479 0.542,0.406 10 false G128 2.802,7.292 4.917,7.594 2.115,0.302 10 false No. 2 CAN Junction Connector 0.146,5 0.688,5.406 0.542,0.406 10 false V12 0.146,5.177 2.115,5.448 1.969,0.271 10 false Multiplex Network Door ECU*3 0.146,3.073 0.688,3.479 0.542,0.406 10 false C60 0.146,3.25 2.042,3.542 1.896,0.292 10 false 4 Wheel Drive Control ECU 6.198,1.24 6.74,1.646 0.542,0.406 10 false G49 6.177,1.417 6.719,1.823 0.542,0.406 10 false ECM 4.813,3.125 7.031,3.51 2.219,0.385 10 false Air Conditioning Amplifier Assembly 5.031,5.031 7,5.646 1.969,0.615 10 false Navigation Receiver Assembly*4 or Radio and Display Receiver Assembly*5 0.177,7.74 2.917,8.052 2.74,0.313 10 false *1: for Automatic Air Conditioning System 0.188,8.063 2.188,8.427 2,0.365 10 false *2: for Manual Cooler System 4.094,4.073 4.635,4.479 0.542,0.406 10 false G126 2.958,0.781 3.5,1.188 0.542,0.406 10 false G120 4.083,0.781 4.625,1.188 0.542,0.406 10 false G122 4.229,0.031 4.771,0.438 0.542,0.406 10 false 1 4.229,0.573 4.771,0.979 0.542,0.406 10 false 2 0.875,2.146 1.417,2.552 0.542,0.406 10 false CANH 0.896,2.688 1.438,3.094 0.542,0.406 10 false CANL 4.115,2.708 4.656,3.115 0.542,0.406 10 false G121 4.24,2.479 4.781,2.885 0.542,0.406 10 false 2 4.229,1.938 4.771,2.344 0.542,0.406 10 false 1 2.969,2.708 3.51,3.115 0.542,0.406 10 false G125 3.083,1.948 3.625,2.354 0.542,0.406 10 false 1 3.104,2.479 3.646,2.885 0.542,0.406 10 false 2 1.406,2.042 1.948,2.448 0.542,0.406 10 false 20 1.396,2.573 1.938,2.979 0.542,0.406 10 false 40 1.396,3.948 1.938,4.354 0.542,0.406 10 false 13 1.396,4.5 1.938,4.906 0.542,0.406 10 false 14 0.896,4.073 1.438,4.479 0.542,0.406 10 false CANP 0.896,4.604 1.438,5.01 0.542,0.406 10 false CANN 2.969,4.604 3.51,5.01 0.542,0.406 10 false G128 3.083,3.833 3.625,4.24 0.542,0.406 10 false 1 3.094,4.375 3.635,4.781 0.542,0.406 10 false 2 5.969,0.135 6.51,0.542 0.542,0.406 10 false CANH 5.979,0.917 6.521,1.323 0.542,0.406 10 false CANL 5.156,2.177 5.698,2.583 0.542,0.406 10 false G37 5.531,2.167 6.073,2.573 0.542,0.406 10 false G131 5.979,2.167 6.521,2.573 0.542,0.406 10 false TX+ 5.979,2.698 6.521,3.104 0.542,0.406 10 false TX- 5.552,2.688 6.094,3.094 0.542,0.406 10 false G131 5.156,2.698 5.698,3.104 0.542,0.406 10 false G37 5.979,4.063 6.521,4.469 0.542,0.406 10 false CANH 5.969,4.604 6.51,5.01 0.542,0.406 10 false CANL 5.177,4.063 5.719,4.469 0.542,0.406 10 false G41 5.552,4.063 6.094,4.469 0.542,0.406 10 false G100 5.552,4.594 6.094,5 0.542,0.406 10 false G100 5.167,4.594 5.708,5 0.542,0.406 10 false G41 5.135,1.938 5.677,2.344 0.542,0.406 10 false 11*1 5.146,2.469 5.688,2.875 0.542,0.406 10 false 12*1 5.594,1.938 6.135,2.344 0.542,0.406 10 false 8*2 5.604,2.469 6.146,2.875 0.542,0.406 10 false 9*2 5.188,3.844 5.729,4.25 0.542,0.406 10 false 9*4 5.146,4.365 5.688,4.771 0.542,0.406 10 false 10*4 5.615,3.844 6.156,4.25 0.542,0.406 10 false 9*5 5.573,4.375 6.115,4.781 0.542,0.406 10 false 10*5 4.094,4.604 4.635,5.01 0.542,0.406 10 false G126 4.219,3.833 4.76,4.24 0.542,0.406 10 false 1 4.219,4.375 4.76,4.781 0.542,0.406 10 false 2 4.094,6.042 4.635,6.448 0.542,0.406 10 false G123 4.094,6.573 4.635,6.979 0.542,0.406 10 false G123 4.219,5.802 4.76,6.208 0.542,0.406 10 false 1 4.229,6.354 4.771,6.76 0.542,0.406 10 false 2 2.938,7.76 4.938,8.125 2,0.365 10 false *4: w/ Navigation System 2.938,8.073 5.073,8.427 2.135,0.354 10 false *5: w/ Audio and Visual System 0.198,8.344 2.417,8.604 2.219,0.26 10 false *3: w/ Power Back Door System

C334535E02
1.417,0.417 1.906,0.76 0.49,0.344 10 false 22 0.885,0.552 1.375,0.896 0.49,0.344 10 false CANH 0.917,1.094 1.406,1.438 0.49,0.344 10 false CANL 1.417,0.969 1.906,1.313 0.49,0.344 10 false 10 3,0.552 3.49,0.896 0.49,0.344 10 false G93 3.073,0.323 3.563,0.667 0.49,0.344 10 false 1 4.219,0.333 4.708,0.677 0.49,0.344 10 false 1 3.094,0.865 3.583,1.208 0.49,0.344 10 false 2 1.427,2.406 1.917,2.75 0.49,0.344 10 false 6 4.135,0.552 4.625,0.896 0.49,0.344 10 false G97 1.406,2.938 1.896,3.281 0.49,0.344 10 false 14 1.396,4.302 1.885,4.646 0.49,0.344 10 false 40 1.385,4.844 1.875,5.188 0.49,0.344 10 false 18 3.01,2.521 3.5,2.865 0.49,0.344 10 false G95 4.146,4.417 4.635,4.76 0.49,0.344 10 false G98 5.76,2.396 6.25,2.74 0.49,0.344 10 false 3 5.771,2.938 6.26,3.281 0.49,0.344 10 false 2 5.76,4.281 6.25,4.625 0.49,0.344 10 false 6 5.75,4.844 6.24,5.188 0.49,0.344 10 false 7 4.604,3.417 5.094,3.76 0.49,0.344 10 false G22 4.604,3.594 7.021,4.042 2.417,0.448 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) 4.823,5.333 5.313,5.677 0.49,0.344 10 false G40 4.833,5.5 7.083,5.885 2.25,0.385 10 false Headlight Leveling ECU Assembly*1 0.146,5.333 0.635,5.677 0.49,0.344 10 false G17 0.135,5.49 3.229,5.844 3.094,0.354 10 false Certification ECU (Smart Key ECU Assembly)*2 2.833,7.292 4.771,7.594 1.938,0.302 10 false No. 1 CAN Junction Connector 5.208,7.219 5.698,7.563 0.49,0.344 10 false G8 5.208,7.375 7.063,7.698 1.854,0.323 10 false Combination Meter Assembly 0.104,1.625 2.948,1.969 2.844,0.344 10 false Brake Actuator Assembly (Skid Control ECU) 0.76,3.469 1.25,3.813 0.49,0.344 10 false G7 0.698,3.635 1.188,3.979 0.49,0.344 10 false DLC3 0.885,2.521 1.375,2.865 0.49,0.344 10 false CANH 0.917,3.073 1.406,3.417 0.49,0.344 10 false CANL 0.875,4.427 1.365,4.771 0.49,0.344 10 false CANH 5.979,4.958 6.469,5.302 0.49,0.344 10 false CANL 3.01,4.427 3.5,4.771 0.49,0.344 10 false G99 2.99,3.052 3.479,3.396 0.49,0.344 10 false G95 3.01,4.969 3.5,5.313 0.49,0.344 10 false G99 4.135,1.083 4.625,1.427 0.49,0.344 10 false G97 3.01,1.083 3.5,1.427 0.49,0.344 10 false G93 4.135,3.063 4.625,3.406 0.49,0.344 10 false G94 4.135,2.531 4.625,2.875 0.49,0.344 10 false G94 4.229,0.854 4.719,1.198 0.49,0.344 10 false 2 4.219,2.302 4.708,2.646 0.49,0.344 10 false 1 3.073,2.302 3.563,2.646 0.49,0.344 10 false 1 3.094,2.833 3.583,3.177 0.49,0.344 10 false 2 4.229,2.833 4.719,3.177 0.49,0.344 10 false 2 5.99,4.427 6.479,4.771 0.49,0.344 10 false CANH 0.906,4.958 1.396,5.302 0.49,0.344 10 false CANL 5.99,2.521 6.479,2.865 0.49,0.344 10 false CANH 5.99,3.073 6.479,3.417 0.49,0.344 10 false CANL 5.969,6.188 6.458,6.531 0.49,0.344 10 false CANH 5.979,6.979 6.469,7.323 0.49,0.344 10 false CANL 4.146,4.948 4.635,5.292 0.49,0.344 10 false G98 0.24,8.042 1.854,8.333 1.615,0.292 10 false *1: for LED Headlight 4.125,6.313 4.615,6.656 0.49,0.344 10 false G96 4.125,6.854 4.615,7.198 0.49,0.344 10 false G96 3.094,4.208 3.583,4.552 0.49,0.344 10 false 1 3.094,4.75 3.583,5.094 0.49,0.344 10 false 2 4.219,4.198 4.708,4.542 0.49,0.344 10 false 1 4.229,4.729 4.719,5.073 0.49,0.344 10 false 2 4.219,6.635 4.708,6.979 0.49,0.344 10 false 2 4.208,6.104 4.698,6.448 0.49,0.344 10 false 1 5.688,6.208 6.177,6.552 0.49,0.344 10 false 36 5.698,6.75 6.188,7.094 0.49,0.344 10 false 35 0.24,8.354 2.646,8.667 2.406,0.313 10 false *2: w/ Smart Entry and Start System 0.125,1.469 0.615,1.813 0.49,0.344 10 false A4

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

·

When replacing the combination meter assembly, make sure to replace it with a new one.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the service bulletin.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.

·

When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION



PROCEDURE

1.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)
a.
C300827C21
0.115,0.99 0.521,1.25 0.406,0.26 1.948,0.917 1.552,0.385 1.552,0.385 1.406,0.385 true 1.938,1.49 1.781,1.906 1.781,1.906 1.594,1.906 true 2.313,1.49 2.51,1.906 2.51,1.906 2.646,1.906 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.219,1.042 0.469,1.219 0.25,0.177 10 false G7 1,0.333 1.49,0.479 0.49,0.146 10 false CANH 1.25,1.833 1.865,2.031 0.615,0.198 10 false CANL 2.719,1.844 3.063,2 0.344,0.156 10 false BAT
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-6 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G7-14 (CANL) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

2.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR SIDE)
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR SIDE)
a.
C300827C21
0.115,0.99 0.521,1.25 0.406,0.26 1.948,0.917 1.552,0.385 1.552,0.385 1.406,0.385 true 1.938,1.49 1.781,1.906 1.781,1.906 1.594,1.906 true 2.313,1.49 2.51,1.906 2.51,1.906 2.646,1.906 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.219,1.042 0.469,1.219 0.25,0.177 10 false G7 1,0.333 1.49,0.479 0.49,0.146 10 false CANH 1.25,1.833 1.865,2.031 0.615,0.198 10 false CANL 2.719,1.844 3.063,2 0.344,0.156 10 false BAT
*a Front view of DLC3


Disconnect the No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-6 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G7-14 (CANL) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)

NG

21.CONNECT CONNECTOR
4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

C334537C01
5.51,2.188 5.979,2.448 0.469,0.26 3.594,2.906 3.781,2.594 3.781,2.594 3.906,2.594 true 3.594,3 3.802,3.292 3.802,3.292 3.927,3.292 true 6.198,3.146 6.333,3.583 6.333,3.583 6.5,3.583 true 0.135,0.125 0.604,0.438 0.469,0.313 10 false *1 2.813,2.406 3.146,2.781 0.333,0.375 10 false *a 4.802,2.26 5.26,2.604 0.458,0.344 10 false *b 5.667,2.219 6.125,2.563 0.458,0.344 10 false G7 3.958,2.531 4.458,2.885 0.5,0.354 10 false CANH 3.969,3.208 4.469,3.563 0.5,0.354 10 false CANL 1.427,1.667 1.927,2.021 0.5,0.354 10 false G123 1.427,1.885 1.927,2.24 0.5,0.354 10 false G122 1.427,2.094 1.927,2.448 0.5,0.354 10 false G128 1.438,2.313 1.938,2.667 0.5,0.354 10 false G125 1.438,2.542 1.938,2.896 0.5,0.354 10 false G126 1.438,2.771 1.938,3.125 0.5,0.354 10 false G121 1.438,3.208 1.938,3.563 0.5,0.354 10 false G120 6.552,3.49 7.01,3.688 0.458,0.198 10 false BAT
*1 No. 2 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Navigation System

*2: w/ Audio and Visual System

*3: w/ Power Back Door System

G120 Y W Airbag Sensor Assembly
G121 GR W Air Conditioning Amplifier Assembly
G122 B W ECM
G125 R W 4 Wheel Drive Control ECU
G126 V W
·

Navigation Receiver Assembly*1

·

Radio and Display Receiver Assembly*2


G128 SB W Multiplex Network Door ECU*3

Standard Resistance:
Tester Connection Condition Specified Condition

*: w/ Power Back Door System

G120-1 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G120-2 (CANL) - G7-16 (BAT)
G121-1 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G121-2 (CANL) - G7-16 (BAT)
G122-1 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G122-2 (CANL) - G7-16 (BAT)
G125-1 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G125-2 (CANL) - G7-16 (BAT)
G126-1 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G126-2 (CANL) - G7-16 (BAT)
G128-1 (CANH) - G7-16 (BAT)* Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G128-2 (CANL) - G7-16 (BAT)*



Result:
Result Proceed to
OK A
NG (to airbag sensor assembly CAN branch wire) B
NG (to air conditioning amplifier assembly CAN branch wire) (for Automatic Air Conditioning System) C
NG (to air conditioning amplifier assembly CAN branch wire) (for Manual Cooler System) D
NG (to ECM CAN main wire) E
NG (to 4 wheel drive control ECU CAN branch wire) F
NG (to navigation receiver assembly CAN branch wire) (w/ Navigation System) G
NG (to radio and display receiver assembly CAN branch wire) (w/ Audio and Visual System) H
NG (to multiplex network door ECU CAN branch wire) (w/ Power Back Door System) I



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

5.CONNECT CONNECTOR

C

7.CONNECT CONNECTOR

D

9.CONNECT CONNECTOR

E

11.CONNECT CONNECTOR

F

13.CONNECT CONNECTOR

G

15.CONNECT CONNECTOR

H

17.CONNECT CONNECTOR

I

19.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
a.
C317109C03
1.479,2.573 1.958,2.865 0.479,0.292 1.531,0.125 2.01,0.417 0.479,0.292 2.083,1.094 2.469,0.615 2.469,0.615 2.625,0.615 true 2.188,1.344 2.5,1.906 2.5,1.906 2.646,1.906 true 2.656,4.333 2.51,4.333 2.51,4.333 2.344,3.802 true 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 0.156,2.542 0.469,2.698 0.313,0.156 10 false *b 1.656,0.188 2.115,0.385 0.458,0.198 10 false G46 1.646,2.625 2.104,2.823 0.458,0.198 10 false G7 2.688,0.531 3.302,0.729 0.615,0.198 10 false CANH 2.708,1.813 3.198,2.042 0.49,0.229 10 false CANL 2.729,4.26 3.344,4.458 0.615,0.198 10 false BAT
*a Rear view of wire harness connector
(to Airbag sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G46-13 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G46-22 (CANL) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIRBAG SENSOR ASSEMBLY (CANH, CANL)

7.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
a.
C317114C01
1.448,2.521 1.927,2.781 0.479,0.26 1.521,0.125 2,0.385 0.479,0.26 1.74,1.083 2.49,0.531 2.49,0.531 2.635,0.531 true 1.646,1.073 0.885,0.552 0.885,0.552 0.719,0.552 true 2.688,4.344 2.531,4.344 2.531,4.344 2.344,3.802 true 0.104,0.063 0.417,0.219 0.313,0.156 10 false *a 0.104,2.438 0.417,2.594 0.313,0.156 10 false *b 1.646,0.177 2.104,0.375 0.458,0.198 10 false G37 1.604,2.573 2.063,2.771 0.458,0.198 10 false G7 2.719,0.438 3.177,0.635 0.458,0.198 10 false TX+ 0.438,0.458 0.896,0.656 0.458,0.198 10 false TX- 2.76,4.26 3.219,4.458 0.458,0.198 10 false BAT
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-11 (TX+) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G37-12 (TX-) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (TX+, TX-)

9.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
a.
C300856C13
1.542,2.781 1.958,3.052 0.417,0.271 1.396,0.208 1.813,0.479 0.417,0.271 1.865,1.927 1.979,1.927 1.979,1.927 2.521,1.063 true 2.667,1.063 2.719,1.948 2.719,1.948 2.833,1.948 true 1.781,4.427 1.906,4.427 1.906,4.427 2.344,3.958 true 0.146,0.104 0.458,0.26 0.313,0.156 10 false *a 0.198,2.635 0.51,2.792 0.313,0.156 10 false *b 1.656,2.844 1.938,3.01 0.281,0.167 10 false G7 1.448,0.25 1.927,0.573 0.479,0.323 10 false G131 1.583,1.844 2.01,2 0.427,0.156 10 false TX+ 2.896,1.875 3.323,2.031 0.427,0.156 10 false TX- 1.469,4.365 1.896,4.521 0.427,0.156 10 false BAT
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G131-8 (TX+) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G131-9 (TX-) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (TX+, TX-)

11.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM MAIN WIRE)
12.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM MAIN WIRE)
a.
C317106C17
1.49,0.094 1.917,0.396 0.427,0.302 1.448,2.542 1.875,2.844 0.427,0.302 2.594,4.313 2.458,4.313 2.458,4.313 2.344,3.813 true 0.688,2.031 0.833,2.031 0.833,2.031 1.073,1.563 true 0.677,1 0.802,1 0.802,1 1.052,1.292 true 1.573,0.146 1.969,0.406 0.396,0.26 10 false G49 1.583,2.604 2.042,2.802 0.458,0.198 10 false G7 0.24,0.917 0.802,1.229 0.563,0.313 10 false CANH 0.281,1.938 0.823,2.24 0.542,0.302 10 false CANL 2.677,4.229 3.292,4.427 0.615,0.198 10 false BAT 0.115,0.094 0.5,0.344 0.385,0.25 10 false *a 0.156,2.469 0.469,2.625 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G49-17 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G49-28 (CANL) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

13.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (4 WHEEL DRIVE CONTROL ECU BRANCH WIRE)
14.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (4 WHEEL DRIVE CONTROL ECU BRANCH WIRE)
a.
C317105C01
1.458,0.198 1.917,0.469 0.458,0.271 1.344,2.552 1.802,2.823 0.458,0.271 2.948,1.198 2.833,0.531 2.833,0.531 2.677,0.531 true 2.635,4.271 2.5,4.271 2.5,4.271 2.344,3.802 true 2.948,1.438 2.875,2.021 2.875,2.021 2.719,2.021 true 0.073,0.042 0.385,0.198 0.313,0.156 10 false *a 0.125,2.521 0.438,2.677 0.313,0.156 10 false *b 1.563,0.25 2.021,0.448 0.458,0.198 10 false C60 1.5,2.615 1.958,2.813 0.458,0.198 10 false G7 2.313,1.948 2.74,2.208 0.427,0.26 10 false CANL 2.24,0.469 2.677,0.76 0.438,0.292 10 false CANH 2.729,4.188 3.344,4.385 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)
*b Front view of DLC3


Disconnect the 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C60-20 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
C60-40 (CANL) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4 WHEEL DRIVE CONTROL ECU (CANH, CANL)

15.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

16.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
16.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
a.
C317107C01
1.448,2.531 1.917,2.833 0.469,0.302 1.51,0.177 1.979,0.479 0.469,0.302 1.948,1.125 0.938,0.594 0.938,0.594 0.771,0.594 true 2.063,1.135 2.521,0.646 2.521,0.646 2.656,0.646 true 2.74,4.333 2.583,4.333 2.583,4.333 2.344,3.792 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 0.146,2.479 0.458,2.635 0.313,0.156 10 false *b 1.615,0.24 2.073,0.438 0.458,0.198 10 false G41 1.615,2.594 2.073,2.792 0.458,0.198 10 false G7 0.344,0.531 0.958,0.729 0.615,0.198 10 false CANH 2.729,0.552 3.344,0.75 0.615,0.198 10 false CANL 2.802,4.25 3.417,4.448 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
*b Front view of DLC3


Disconnect the navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G41-9 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G41-10 (CANL) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION RECEIVER ASSEMBLY (CANH, CANL)

17.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
a.
C317107C03
1.448,2.531 1.917,2.833 0.469,0.302 1.51,0.177 1.979,0.479 0.469,0.302 1.948,1.125 0.938,0.594 0.938,0.594 0.771,0.594 true 2.063,1.135 2.521,0.646 2.521,0.646 2.656,0.646 true 2.74,4.333 2.583,4.333 2.583,4.333 2.344,3.792 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 0.146,2.479 0.458,2.635 0.313,0.156 10 false *b 1.573,0.24 2.031,0.438 0.458,0.198 10 false G100 1.615,2.594 2.073,2.792 0.458,0.198 10 false G7 0.344,0.531 0.958,0.729 0.615,0.198 10 false CANH 2.729,0.552 3.344,0.75 0.615,0.198 10 false CANL 2.802,4.25 3.417,4.448 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of DLC3


Disconnect the radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G100-9 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G100-10 (CANL) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

19.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MULTIPLEX NETWORK DOOR ECU BRANCH WIRE)
20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MULTIPLEX NETWORK DOOR ECU BRANCH WIRE)
a.
C300869C03
0.24,0.792 0.656,1.052 0.417,0.26 0.281,2.51 0.698,2.771 0.417,0.26 0.76,1.604 0.865,1.604 0.865,1.604 0.979,1.229 true 1.5,1.635 1.385,1.635 1.385,1.635 1.094,1.219 true 2.594,3.177 2.479,3.177 2.479,3.177 2.271,2.896 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 0.094,1.844 0.406,2 0.313,0.156 10 false *b 0.406,2.563 0.719,2.719 0.313,0.156 10 false G7 0.333,0.854 0.646,1.01 0.313,0.156 10 false V12 0.375,1.542 0.802,1.708 0.427,0.167 10 false CANP 1.563,1.552 1.99,1.719 0.427,0.167 10 false CANN 2.646,3.115 3.073,3.281 0.427,0.167 10 false BAT
*a Front view of wire harness connector
(to Multiplex Network Door ECU)
*b Front view of DLC3


Disconnect the multiplex network door ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V12-13 (CANP) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
V12-14 (CANN) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX NETWORK DOOR ECU (CANP, CANN)

21.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

C329226C01
5.458,2.958 5.875,3.25 0.417,0.292 6.01,4.417 6.135,4.417 6.135,4.417 6.208,3.938 true 3.604,3.625 3.771,3.24 3.771,3.24 3.885,3.24 true 3.604,3.781 3.771,4.073 3.771,4.073 3.885,4.073 true 2.802,3.125 3.115,3.281 0.313,0.156 10 false *a 4.833,3.031 5.146,3.188 0.313,0.156 10 false *b 0.073,0.094 0.521,0.302 0.448,0.208 10 false *1 3.948,3.156 4.406,3.354 0.458,0.198 10 false CANH 3.948,4 4.385,4.198 0.438,0.198 10 false CANL 5.604,3.031 5.917,3.229 0.313,0.198 10 false G7 5.677,4.333 6.021,4.531 0.344,0.198 10 false BAT 1.479,3.979 1.938,4.177 0.458,0.198 10 false G93 1.458,3.75 1.917,3.948 0.458,0.198 10 false G94 1.469,3.531 1.927,3.729 0.458,0.198 10 false G95 1.469,3.302 1.927,3.5 0.458,0.198 10 false G96 1.469,3.083 1.927,3.281 0.458,0.198 10 false G97 1.469,2.865 1.927,3.063 0.458,0.198 10 false G98 1.469,2.646 1.927,2.844 0.458,0.198 10 false G99
*1 No. 1 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: for LED Headlight

*2: w/ Smart Entry and Start System

G93 B W Brake Actuator Assembly (Skid Control ECU)
G94 BE W Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)
G96 SB W Combination Meter Assembly
G97 LG W No. 2 CAN Junction Connector
G98 V W Headlight Leveling ECU Assembly*1
G99 G W Certification ECU (Smart Key ECU Assembly)*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*1: for LED Headlight

*2: w/ Smart Entry and Start System

G93-1 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G93-2 (CANL) - G7-16 (BAT)
G94-1 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G94-2 (CANL) - G7-16 (BAT)
G96-1 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G96-2 (CANL) - G7-16 (BAT)
G97-1 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G97-2 (CANL) - G7-16 (BAT)
G98-1 (CANH) - G7-16 (BAT)*1 Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G98-2 (CANL) - G7-16 (BAT)*1
G99-1 (CANH) - G7-16 (BAT)*2 Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G99-2 (CANL) - G7-16 (BAT)*2



Result:
Result Proceed to
OK A
NG (to brake actuator assembly [skid control ECU] CAN branch wire) B
NG (to spiral with sensor cable sub-assembly [steering angle sensor] CAN branch wire) C
NG (to combination meter assembly CAN main wire) D
NG (to headlight leveling ECU assembly CAN branch wire) E
NG (to certification ECU [smart key ECU assembly] CAN branch wire) (w/ Smart Entry and Start System) F
NG (to No. 2 CAN junction connector CAN main wire) G



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

23.CONNECT CONNECTOR

C

25.CONNECT CONNECTOR

D

27.CONNECT CONNECTOR

E

29.CONNECT CONNECTOR

F

31.CONNECT CONNECTOR

G

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

23.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)
24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)
a.

Disconnect the brake actuator assembly (skid control ECU) connector.

C334538C01
1.958,0.427 2.417,0.719 0.458,0.292 4.875,0.5 5.333,0.792 0.458,0.292 1.917,2.167 2.083,2.167 2.083,2.167 2.531,1.333 true 5.167,2.083 5.333,2.083 5.333,2.083 5.625,1.563 true 2.531,1.219 1.656,0.719 1.656,0.719 1.49,0.719 true 0.771,0.375 1.177,0.646 0.406,0.271 10 false *a 3.938,0.365 4.365,0.656 0.427,0.292 10 false *b 2.115,0.479 2.521,0.75 0.406,0.271 10 false A4 5.021,0.552 5.448,0.844 0.427,0.292 10 false G7 4.844,2.01 5.323,2.313 0.479,0.302 10 false BAT 1.469,2.073 1.948,2.375 0.479,0.302 10 false CANH 1.073,0.635 1.552,0.938 0.479,0.302 10 false CANL
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
*b Front view of DLC3



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-22 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A4-10 (CANL) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

25.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

26.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)
26.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)
a.
C317110C01
1.49,2.521 1.958,2.792 0.469,0.271 1.542,0.167 2.01,0.438 0.469,0.271 1.813,1.344 1.958,1.906 1.958,1.906 2.094,1.906 true 1.635,1.354 1.469,1.854 1.469,1.854 1.323,1.854 true 2.344,3.781 2.49,4.281 2.49,4.281 2.625,4.281 true 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 0.146,2.458 0.458,2.615 0.313,0.156 10 false *b 1.646,0.219 2.104,0.417 0.458,0.198 10 false G22 1.635,2.573 2.094,2.771 0.458,0.198 10 false G7 2.167,1.813 2.781,2.01 0.615,0.198 10 false CANH 0.906,1.802 1.323,2.042 0.417,0.24 10 false CANL 2.708,4.208 3.323,4.406 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])
*b Front view of DLC3


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G22-3 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G22-2 (CANL) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (CANH, CANL)

27.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

28.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY MAIN WIRE)
28.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY MAIN WIRE)
a.
C317111C01
1.479,2.583 1.938,2.875 0.458,0.292 1.458,0.052 1.917,0.344 0.458,0.292 1.385,1.073 1.219,1.948 1.219,1.948 1.083,1.948 true 2.656,4.26 2.521,4.26 2.521,4.26 2.344,3.792 true 1.313,1.073 1.073,1.615 1.073,1.615 0.938,1.615 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 0.146,2.521 0.458,2.677 0.313,0.156 10 false *b 1.604,0.125 1.917,0.323 0.313,0.198 10 false G8 1.635,2.635 1.948,2.833 0.313,0.198 10 false G7 0.51,1.542 1.125,1.74 0.615,0.198 10 false CANH 0.667,1.875 1.281,2.073 0.615,0.198 10 false CANL 2.74,4.167 3.354,4.365 0.615,0.198 10 false BAT
*a Rear view of wire harness connector
(to Combination Meter Assembly)
*b Front view of DLC3


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-36 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G8-35 (CANL) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

29.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

30.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (HEADLIGHT LEVELING ECU ASSEMBLY BRANCH WIRE)
30.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (HEADLIGHT LEVELING ECU ASSEMBLY BRANCH WIRE)
a.
C317113C01
1.417,2.51 1.906,2.781 0.49,0.271 1.49,0.125 1.979,0.396 0.49,0.271 2.24,0.938 1.146,0.417 1.146,0.417 0.969,0.417 true 2.646,4.365 2.521,4.365 2.521,4.365 2.333,3.781 true 2.417,0.948 2.563,0.385 2.563,0.385 2.688,0.385 true 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 0.146,2.49 0.458,2.646 0.313,0.156 10 false *b 1.594,0.177 2.052,0.375 0.458,0.198 10 false G40 1.583,2.573 2.042,2.771 0.458,0.198 10 false G7 0.542,0.344 1.156,0.542 0.615,0.198 10 false CANH 2.74,0.302 3.354,0.5 0.615,0.198 10 false CANL 2.74,4.271 3.354,4.469 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)
*b Front view of DLC3


Disconnect the headlight leveling ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G40-6 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G40-7 (CANL) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT LEVELING ECU ASSEMBLY (CANH, CANL)

31.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

32.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CERTIFICATION ECU BRANCH WIRE)
32.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CERTIFICATION ECU BRANCH WIRE)
a.
C317104C01
1.417,2.521 1.896,2.813 0.479,0.292 1.458,0.125 1.938,0.417 0.479,0.292 2.594,4.354 2.438,4.354 2.438,4.354 2.354,3.802 true 3.094,1.052 2.833,0.427 2.833,0.427 2.677,0.427 true 3.063,1.26 2.875,2 2.875,2 2.719,2 true 0.073,0.052 0.385,0.208 0.313,0.156 10 false *a 0.094,2.438 0.406,2.594 0.313,0.156 10 false *b 1.573,0.188 2.031,0.385 0.458,0.198 10 false G17 1.573,2.583 2.031,2.781 0.458,0.198 10 false G7 2.688,4.25 3.146,4.448 0.458,0.198 10 false BAT 2.281,1.927 2.771,2.188 0.49,0.26 10 false CANH 2.26,0.365 2.698,0.625 0.438,0.26 10 false CANL
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])
*b Front view of DLC3


Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-40 (CANH) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G17-18 (CANL) - G7-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)