Home › Engine / Hybrid System › 1KD-FTV LUBRICATION › OIL PUMP › from 2016.01
RM3270E _51 Engine / Hybrid System _048920 1KD-FTV LUBRICATION _0242496 OIL PUMP A

1KD-FTV LUBRICATION  OIL PUMP  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 11320 1.INSTALL TIMING GEAR CASE ASSEMBLY

Hide 15104 2.INSTALL OIL STRAINER SUB-ASSEMBLY

Hide 12101 3.INSTALL OIL PAN SUB-ASSEMBLY

Hide 22100 4.INSTALL FUEL SUPPLY PUMP ASSEMBLY

Hide 13521 6.INSTALL CRANKSHAFT TIMING GEAR

Hide 13581 7.INSTALL NO. 1 IDLE GEAR SHAFT

Hide 19315 9.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 13408 11.INSTALL CRANKSHAFT PULLEY SUB-ASSEMBLY

Hide 13522P 12.INSTALL PUMP DRIVE SHAFT PULLEY

a.

Install a new O-ring to the fuel supply pump assembly.


b.

Temporarily install the fuel supply pump assembly with the nut.


c.
A352009C01
1.042,1.281 0.781,1.563 0.781,1.563 0.635,1.563 true 1.708,1.302 2.427,1.802 2.427,1.802 2.563,1.802 false 2.594,1.708 2.938,1.906 0.344,0.198 10 true SST 0.302,1.458 0.635,1.646 0.333,0.188 10 true SST 1.208,1.948 1.417,2.115 0.208,0.167 10 true *a
*a Hold
V100135

Turn


Using SST, hold the crankshaft pulley and tighten the nut.

SST
09213-58014  (91551-80840)
09330-00021  

Torque:
63.7 N*m (650 kgf*cm, 47 ft.*lbf)


d.

Install the No. 2 camshaft timing pulley flange and pump drive shaft pulley to the timing gear cover with the 4 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


e.
A352010

Using a dial indicator, check the thrust clearance of the pump drive shaft while moving the pump drive shaft pulley back and forth.

Standard thrust clearance (reference):

0.15 to 0.55 mm (0.00591 to 0.0217 in.)


HINT:

If there is no clearance, remove and reinstall the fuel supply pump assembly and pump drive shaft pulley. Then repeat the step above.



Hide 29300 16.INSTALL VACUUM PUMP ASSEMBLY

Hide 16100 17.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 11201 20.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23804C 21.INSTALL FUEL INLET PIPE SUB-ASSEMBLY

Hide 15301 22.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 23704 23.INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY

Hide 23701 24.INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

Hide 88431 26.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 16620 27.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 27020 29.INSTALL GENERATOR ASSEMBLY

Hide 30.INSTALL NO. 2 IDLE PULLEY ASSEMBLY

Hide 13505 31.INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

Hide 11322A 33.INSTALL NO. 1 TIMING BELT COVER

Hide 36.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 39.BLEED AIR FROM POWER STEERING SYSTEM

Hide 40.INSPECT FOR POWER STEERING FLUID LEVEL

Hide 41.PERFORM REGISTRATION

a.

Perform registration of the injector compensation codes.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


b.