The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for control of the ABS.
Each of the front and rear rotors have 48 serrations. When the rotors rotate, the magnetic field generated by the permanent magnet in the speed sensor produces AC voltage. Since the frequency of this AC voltage changes in direct proportion to the speed of the rotor, the frequency is used by the skid control ECU (brake actuator assembly) to detect the speed of each wheel.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| C0210/33 | Rear Speed Sensor RH Circuit | One of the following conditions is met:
1.
At a vehicle speed of 10 km/h (6 mph) or more, an open or short in the sensor signal circuit continues for 15 seconds or more. 2.
Momentary interruption of the sensor signal from the abnormal wheel occurs 7 times or more. 3.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. |
·
Rear speed sensor RH ·
Rear speed sensor circuit ·
Rear skid control rotor RH ·
Sensor installation ·
Skid control ECU (Brake actuator assembly) |
- |
| C0215/34 | Rear Speed Sensor LH Circuit | One of the following conditions is met:
1.
At a vehicle speed of 10 km/h (6 mph) or more, an open or short in the sensor signal circuit continues for 15 seconds or more. 2.
Momentary interruption of the sensor signal from the abnormal wheel occurs 7 times or more. 3.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. |
·
Rear speed sensor LH ·
Rear speed sensor circuit ·
Rear skid control rotor LH ·
Sensor installation ·
Skid control ECU (Brake actuator assembly) |
- |
| C1238/38 | Foreign Object is Attached on Tip of Rear Speed Sensor RH | At a vehicle speed of 20 km/h (12 mph) or more, condition that noise is included in speed sensor signal continues for 5 seconds or more. | ·
Rear speed sensor RH ·
Rear speed sensor circuit ·
Sensor installation |
- |
| C1239/39 | Foreign Object is Attached on Tip of Rear Speed Sensor LH | At a vehicle speed of 20 km/h (12 mph) or more, condition that noise is included in speed sensor signal continues for 5 seconds or more. | ·
Rear speed sensor LH ·
Rear speed sensor circuit ·
Sensor installation |
- |
| C1273/73 | Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) | Detected only during Test Mode. | ·
Rear speed sensor RH ·
Sensor installation ·
Rear skid control rotor RH |
The code in this table is output only in Test Mode. |
| C1274/74 | Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) | Detected only during Test Mode. | ·
Rear speed sensor LH ·
Sensor installation ·
Rear skid control rotor LH |
The code in this table is output only in Test Mode. |
| C1277/77 | Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) | Detected only during Test Mode. | Rear skid control rotor RH | The code in this table is output only in Test Mode. |
| C1278/78 | Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) | Detected only during Test Mode. | Rear skid control rotor LH | The code in this table is output only in Test Mode. |
DTCs C0210/33, C1238/38, C1273/73 and C1277/77 are for the rear speed sensor RH.
DTCs C0215/34, C1239/39, C1274/74 and C1278/78 are for the rear speed sensor LH.
Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).
Before disconnecting the connector, make sure that there are no problems with the connection.
After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
Using the intelligent tester, check for any momentary interruptions in the wire harness and connector corresponding to the DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Speed Open | Rear speed sensor RH open circuit detection | Opn_Det or Normal | Normal | - |
| RL Speed Open | Rear speed sensor LH open circuit detection | Opn_Det or Normal | Normal | - |
| Tester Display |
|---|
| RR Speed Open |
| RL Speed Open |
Normal (There are no momentary interruptions.)
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
Start the engine.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Wheel Speed | Rear speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Actual wheel speed | No large fluctuations when driving at a constant speed. |
| RL Wheel Speed | Rear speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Actual wheel speed | No large fluctuations when driving at a constant speed. |
| Tester Display |
|---|
| RR Wheel Speed |
| RL Wheel Speed |
Check the speed value output from the speed sensor displayed on the intelligent tester.
Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK
The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the sensor check in the Test Mode procedure.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE
All Test Mode DTCs are cleared.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC not output | A |
| DTC output | B |
If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Check that the skid control ECU (brake actuator assembly) and the rear speed sensor connectors are securely connected.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC output | A |
| DTC not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
| *1 | Rear Speed Sensor |
| *a | No clearance |
| *b | CORRECT |
| *c | INCORRECT |
Check the rear speed sensor installation.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>INSTALLATION
The installation bolt is tightened properly.
There is no clearance between the sensor and rear axle housing.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Remove the rear speed sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL
Check the speed sensor tip.
No scratches, oil or foreign matter on the sensor tip.
Do not replace the speed sensor if no damage to the speed sensor tip is found.
If the sensor is contaminated with oil or other foreign material, clean the sensor.
If there is iron powder sticking to the rotor, this will result in a malfunction. Confirm that the rotor is not contaminated with foreign material before replacing the sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Remove the rear speed sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL
Inspect the rear speed sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A13-11 (RL+) - L12-2 (RL+) | Always | Below 1 Ω |
| A13-11 (RL+) - Body ground | Always | 10 kΩ or higher |
| A13-12 (RL-) - L12-1 (RL-) | Always | Below 1 Ω |
| A13-12 (RL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A13-33 (RR+) - L11-2 (RR+) | Always | Below 1 Ω |
| A13-33 (RR+) - Body ground | Always | 10 kΩ or higher |
| A13-34 (RR-) - L11-1 (RR-) | Always | Below 1 Ω |
| A13-34 (RR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Remove the rear axle shaft with backing plate.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT>REMOVAL
Check the rear skid control rotor.
No scratches, oil or foreign matter on the rotors.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Replace the rear speed sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC output | A |
| DTC not output | B |
A
B