Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1880E _58 Vehicle Interior _013242 SUPPLEMENTAL RESTRAINT SYSTEMS _0068641 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1800/51  Short in Driver Side Squib Circuit  B1801/51  Open in Driver Side Squib Circuit  B1802/51  Short to GND in Driver Side Squib Circuit  B1803/51  Short to B+ in Driver Side Squib Circuit  


DESCRIPTION

The driver side squib circuit consists of the center airbag sensor, spiral cable and steering pad.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib circuit.


DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1800/51 Short in Driver Side Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the driver side squib circuit during the primary check.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly


DTC is output in check mode.
B1801/51 Open in Driver Side Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects an open circuit signal in the driver side squib circuit for 2 seconds.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly


DTC is output in check mode.
B1802/51 Short to GND in Driver Side Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the driver side squib circuit for 0.5 seconds.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly


DTC is output in check mode.
B1803/51 Short to B+ in Driver Side Squib Circuit One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the driver side squib circuit for 0.5 seconds.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly


DTC is output in check mode.

WIRING DIAGRAM

C240457
2.927,1.583 3.25,1.885 0.323,0.302 10 D+ 2.958,2.427 3.208,2.708 0.25,0.281 10 D- 2.156,1.583 2.469,1.885 0.313,0.302 10 D+ 2.198,2.427 2.5,2.719 0.302,0.292 10 D- 4.781,1.677 5.094,1.938 0.313,0.26 10 D+ 4.781,2.521 5.052,2.771 0.271,0.25 10 D- 3.219,1.594 3.5,1.875 0.281,0.281 10 1 3.229,2.417 3.5,2.729 0.271,0.313 10 2 2.479,3 2.906,3.292 0.427,0.292 10 G52 0.781,3 1.146,3.292 0.365,0.292 10 z5 2.479,3.146 3.385,3.5 0.906,0.354 10 Spiral Cable 0.781,3.167 2,3.531 1.219,0.365 10 Driver Side Squib 4.604,1.583 4.875,1.844 0.271,0.26 10 5 4.594,2.427 4.885,2.75 0.292,0.323 10 6 4.813,4.167 5.219,4.458 0.406,0.292 10 G53 4.823,4.323 6.302,4.656 1.479,0.333 10 Center Airbag Sensor 2.479,2.427 2.76,2.729 0.281,0.302 10 1 2.479,1.583 2.75,1.896 0.271,0.313 10 2

CAUTION / NOTICE / HINT

NOTICE:
·

When installing the spiral cable and steering wheel, be sure to adjust the spiral cable as it may break if the steering wheel is turned before adjusting the spiral cable (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK STEERING PAD (DRIVER SIDE SQUIB)
C214258
0.625,2.042 1.042,2.292 0.417,0.25 0.229,1.083 0.229,0.667 false 2.042,2.958 1.844,2.771 true 2.417,2.25 2.063,2.25 false 0.146,1.135 0.406,1.385 0.26,0.25 10 false *1 0.76,1.052 1.115,1.365 0.354,0.313 10 false *2 2.5,1.844 2.792,2.063 0.292,0.219 10 false *4 2.5,2.156 2.854,2.469 0.354,0.313 10 false *5 2.073,2.979 2.427,3.292 0.354,0.313 10 false *b 2.229,1.406 2.583,1.719 0.354,0.313 10 false *3 1.698,0.771 2.052,1.083 0.354,0.313 10 false DC 2.375,0.521 2.729,0.833 0.354,0.313 10 false A 0.76,2.083 1.115,2.396 0.354,0.313 10 false z5 0.313,0.781 0.479,1.021 0.167,0.24 10 false F 0.542,0.771 0.823,1.073 0.281,0.302 10 false E 1.594,1.615 1.948,1.927 0.354,0.313 10 false *a
*1 Driver Side Squib
*2 Spiral Cable
*3 Center Airbag Sensor
*4 Connector E
*5 SST
*a Front view of wire harness connector
(to Driver Side Squib)
*b Color: Orange


a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the steering pad.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.


·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Body Electrical > SRS Airbag > Clear DTCs
50002 63

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Body Electrical > SRS Airbag > Trouble Codes
50001 63
OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


HINT:

Codes other than DTC B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.
C213963
0.219,0.563 0.542,0.875 0.323,0.313 10 *1 0.823,1.219 1.146,1.531 0.323,0.313 10 *2 2.281,1.594 2.604,1.906 0.323,0.313 10 *3 0.417,0.979 0.708,1.281 0.292,0.302 10 F 0.583,0.979 0.875,1.281 0.292,0.302 10 E 1.625,0.969 1.917,1.271 0.292,0.302 10 D 1.75,0.969 2.042,1.271 0.292,0.302 10 C 2.427,0.74 2.719,1.042 0.292,0.302 10 A 2.083,0.969 2.375,1.271 0.292,0.302 10 B
*1 Driver Side Squib
*2 Spiral Cable
*3 Center Airbag Sensor


Disconnect SST from connector E.


d.

Disconnect the connectors from the center airbag sensor.


e.

Check that the connectors (on the center airbag sensor side and steering pad side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK DRIVER SIDE SQUIB CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK DRIVER SIDE SQUIB CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


C214259
0.604,2.104 1.021,2.354 0.417,0.25 0.208,0.917 0.208,0.667 false 1.375,2.438 1.635,2.125 true 1.969,2.438 1.719,2.125 true 2,2.948 1.833,2.771 false 0.125,0.938 0.448,1.219 0.323,0.281 10 false *1 0.771,1.042 1.094,1.323 0.323,0.281 10 false *2 2.406,1.385 2.729,1.667 0.323,0.281 10 false *3 2.385,1.854 2.708,2.135 0.323,0.281 10 false *4 1.573,1.635 1.896,1.917 0.323,0.281 10 false *a 2.031,2.948 2.354,3.229 0.323,0.281 10 false *b 2.552,0.479 2.875,0.76 0.323,0.281 10 false A 2.188,0.719 2.51,1 0.323,0.281 10 false B 1.813,0.74 2.135,1.021 0.323,0.281 10 false C 1.688,0.74 2.01,1.021 0.323,0.281 10 false D 0.323,0.75 0.646,1.031 0.323,0.281 10 false F 0.542,0.75 0.865,1.031 0.323,0.281 10 false E 1.979,2.396 2.302,2.677 0.323,0.281 10 false D+ 0.74,2.146 1.063,2.427 0.323,0.281 10 false z5 1.24,2.396 1.563,2.677 0.323,0.281 10 false D-
*1 Driver Side Squib
*2 Spiral Cable
*3 Center Airbag Sensor
*4 Connector E
*a Front view of wire harness connector
(to Driver Side Squib)
*b Color: Orange


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z5-2 (D+) - Body ground Ignition switch ON Below 1 V
z5-1 (D-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-2 (D+) - z5-1 (D-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-2 (D+) - z5-1 (D-) Always 1 MΩ or higher
z5-2 (D+) - Body ground Always 1 MΩ or higher
z5-1 (D-) - Body ground Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK DTC
a.
C215879
0.292,0.917 0.635,1.229 0.344,0.313 10 *1 2.177,1.573 2.521,1.885 0.344,0.313 10 *3 0.813,1.229 1.156,1.542 0.344,0.313 10 *2 0.49,0.958 0.833,1.271 0.344,0.313 10 F 0.615,0.958 0.958,1.271 0.344,0.313 10 E 1.677,0.969 2.021,1.281 0.344,0.313 10 D 1.813,0.969 2.156,1.281 0.344,0.313 10 C
*1 Driver Side Squib
*2 Spiral Cable
*3 Center Airbag Sensor


Connect the connectors to the steering pad and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Body Electrical > SRS Airbag > Clear DTCs
50002 63

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Body Electrical > SRS Airbag > Trouble Codes
50001 63
OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


HINT:

Codes other than DTC B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK INSTRUMENT PANEL WIRE
a.

Disconnect the instrument panel wire connector from the spiral cable.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


C261407
0.625,2.167 1.042,2.417 0.417,0.25 1.313,2.833 1.708,2.396 true 2.271,2.844 1.875,2.396 true 0.25,0.844 0.521,1.104 0.271,0.26 10 false F 0.438,0.844 0.75,1.188 0.313,0.344 10 false E 1.49,0.844 1.802,1.167 0.313,0.323 10 false D 1.698,0.844 2,1.125 0.302,0.281 10 false C 2,0.844 2.281,1.125 0.281,0.281 10 false B 2.344,0.604 2.583,0.854 0.24,0.25 10 false A 0.656,1.104 0.979,1.396 0.323,0.292 10 false *2 2.177,1.427 2.521,1.76 0.344,0.333 10 false *3 1.781,0.438 2.042,0.688 0.26,0.25 10 false *1 1.135,2.802 1.438,3.063 0.302,0.26 10 false D- 2.458,1.958 2.76,2.271 0.302,0.313 10 false *4 2.333,2.833 2.698,3.135 0.365,0.302 10 false D+ 0.698,2.219 1.021,2.479 0.323,0.26 10 false G52 1.594,1.719 1.917,2.01 0.323,0.292 10 false *a
*1 Instrument Panel Wire
*2 Spiral Cable
*3 Center Airbag Sensor
*4 Connector C
*a Rear view of wire harness connector
(to Spiral Cable)


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G52-1 (D+) - Body ground Ignition switch ON Below 1 V
G52-2 (D-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G52-1 (D+) - G52-2 (D-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G52-1 (D+) - G52-2 (D-) Always 1 MΩ or higher
G52-1 (D+) - Body ground Always 1 MΩ or higher
G52-2 (D-) - Body ground Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE