Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY
RM1880E _59 Vehicle Exterior _013249 DOOR / HATCH _0068717 FUEL LID LOCK CONTROL CABLE ASSEMBLY A

DOOR / HATCH  FUEL LID LOCK CONTROL CABLE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.INSTALL FUEL FILLER OPENING LID LOCK RETAINER

B277117

a.

Install the fuel filler opening lid lock retainer and turn it counterclockwise as shown in the illustration.


Hide 2.INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

B277115

a.

Install the fuel lid lock control cable and turn the fuel filler opening lid lock retainer clockwise as shown in the illustration.


b.

for LHD:

i.

Attach the cable to each of the clamps shown in the illustration and install new tape.


ii.

Install the fuel lid lock open lever.

B279300
6.01,1.927 6.365,2.083 true 0.531,0.948 0.313,0.719 false 6.448,2.042 6.781,2.302 0.333,0.26 10 false *1 0.115,0.542 0.396,0.76 0.281,0.219 10 false *2
*1 Fuel Lid Lock Open Lever *2 Tape




c.

for RHD:

i.

Attach the cable to each of the clamps shown in the illustration and install new tape.


ii.

Install the fuel lid lock open lever.

B279301
0.469,3.49 0.302,3.344 false 6.167,1.469 6.01,1.083 true 6.198,1.542 6.563,1.813 0.365,0.271 10 false *1 0.104,3.208 0.469,3.51 0.365,0.302 10 false *2
*1 Fuel Lid Lock Open Lever *2 Tape




Hide 3.INSTALL FRONT FLOOR CARPET ASSEMBLY

a.

Install the front floor carpet.


Hide 4.INSTALL QUARTER INSIDE TRIM BOARD LH

a.

Attach the 4 claws, 8 clips and 2 guides to install the quarter inside trim board.


b.

Install the clip.


c.

Install the rear door opening trim.


d.

Connect the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


e.

Connect the rear No. 2 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 7.INSTALL LOWER CENTER PILLAR GARNISH LH

a.

Attach the 2 claws to install the lower center pillar garnish.


b.

Install the front door opening trim and rear door opening trim.


c.

Connect the front seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 9.INSTALL COWL SIDE TRIM BOARD LH (for LHD)

a.

Attach the 2 clips to install the cowl side trim board.


b.

Install the clip.


c.

Install the front door opening trim.


Hide 10.INSTALL COWL SIDE TRIM BOARD RH (for RHD)

HINT:

Use the same procedure described for the LH side.


Hide 11.INSTALL FRONT DOOR SCUFF PLATE LH (for LHD)

Hide 12.INSTALL FRONT DOOR SCUFF PLATE RH (for RHD)

Hide 14.INSTALL REAR NO. 2 SEAT ASSEMBLY LH

Hide 15.INSTALL REAR NO. 1 SEAT ASSEMBLY (for Captain Seat Type)

Hide 16.INSTALL REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Tumble Seat Type LH Side)

Hide 17.INSTALL REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Tumble Seat Type RH Side)

Hide 18.INSTALL FRONT SEAT ASSEMBLY LH

Hide 19.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure described for the RH side.