Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY
RM1880E _59 Vehicle Exterior _013249 DOOR / HATCH _0068717 FUEL LID LOCK CONTROL CABLE ASSEMBLY A

DOOR / HATCH  FUEL LID LOCK CONTROL CABLE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.REMOVE FRONT SEAT ASSEMBLY LH

Hide 2.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure described for the RH side.


Hide 3.REMOVE REAR NO. 1 SEAT ASSEMBLY (for Captain Seat Type)

Hide 4.REMOVE REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Tumble Seat Type LH Side)

Hide 5.REMOVE REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Tumble Seat Type RH Side)

Hide 6.REMOVE REAR NO. 2 SEAT ASSEMBLY LH

Hide 9.REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

Hide 10.REMOVE COWL SIDE TRIM BOARD LH (for LHD)

B277609

a.

Remove the part of the front door opening trim attached to the cowl side trim board.


b.

Remove the clip.


c.

Detach the 2 clips and remove the cowl side trim board.


Hide 11.REMOVE COWL SIDE TRIM BOARD RH (for RHD)

HINT:

Use the same procedure described for the LH side.


Hide 13.REMOVE LOWER CENTER PILLAR GARNISH LH

B276978

a.

Remove the bolt and disconnect the front seat outer belt floor anchor.


b.
B279268

Remove the part of the front door opening trim and rear door opening trim attached to the lower center pillar garnish.


c.

Detach the 2 claws and remove the lower center pillar garnish.


Hide 16.REMOVE QUARTER INSIDE TRIM BOARD LH

B279273

a.

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.


b.
B279274

Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.


c.

Remove the part of the rear door opening trim attached to the quarter inside trim board.


d.

Using a clip remover, remove the clip.


e.

Detach the 4 claws, 8 clips and 2 guides and remove the quarter inside trim board.

B279275


Hide 17.REMOVE FRONT FLOOR CARPET ASSEMBLY

a.

Partially remove the floor carpet.

HINT:

It is not necessary to fully remove the floor carpet. Partially remove it so that the lock control cable can be removed in a later step.



Hide 18.REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

a.

for LHD:

i.

Remove the fuel lid lock open lever.


ii.

Remove the tape and detach the cable from each of the clamps shown in the illustration.

B279300
6.042,1.917 6.438,2.146 true 0.521,0.958 0.26,0.646 false 6.521,2.052 6.75,2.25 0.229,0.198 10 false *1 0.042,0.5 0.271,0.698 0.229,0.198 10 false *2
*1 Fuel Lid Lock Open Lever *2 Tape




b.

for RHD:

i.

Remove the fuel lid lock open lever.


ii.

Remove the tape and detach the cable from each of the clamps shown in the illustration.

B279301
0.469,3.49 0.302,3.344 false 6.167,1.469 6.01,1.083 true 6.198,1.542 6.563,1.813 0.365,0.271 10 false *1 0.104,3.208 0.469,3.51 0.365,0.302 10 false *2
*1 Fuel Lid Lock Open Lever *2 Tape




c.
B277114

Turn the fuel filler opening lid lock retainer counterclockwise and remove the fuel lid lock control cable from the fuel filler opening lid lock retainer.


Hide 19.REMOVE FUEL FILLER OPENING LID LOCK RETAINER

B277116

a.

Turn the fuel filler opening lid lock retainer clockwise and remove the fuel filler opening lid lock retainer as shown in the illustration.