C1413 Front Speed Sensor RH Output Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Also covers:
- C1275 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)
- C1276 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)
- C1414 Front Speed Sensor LH Output Malfunction
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Refer to DTCs C1401 and C1402 (Click here).| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1413 C1414 |
One of the following conditions is met:
|
|
| C1275 C1276 |
Stored only during test mode. |
|
- HINT:
- DTC C1413 is for the front speed sensor RH.
- DTC C1414 is for the front speed sensor LH.
- DTC C1413 is for the front speed sensor RH.
WIRING DIAGRAM
Refer to DTCs C1405 and C1406 (Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the brake actuator assembly, perform calibration (Click here).
- Check the speed sensor signal after replacement (Click here).
- When replacing the brake actuator assembly, perform calibration (Click here).
| 1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Speed Open
Front speed sensor RH open circuit detection/ Error or Normal
Normal
-
FL Speed Open
Front speed sensor LH open circuit detection/ Error or Normal
Normal
-
- OK:
- Normal (there are no momentary interruptions).
- HINT:
- Perform the above inspection before removing the sensor and disconnecting the connector.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED) |
Turn the ignition switch off
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Wheel Speed
Front speed sensor RH value/ min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
FL Wheel Speed
Front speed sensor LH value/ min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
|
|
||||
| OK | |
| 3. PERFORM TEST MODE (SIGNAL CHECK) |
Perform the signal check in the test mode procedure (Click here).
- OK:
- All test mode DTCs are cleared.
|
|
||||
| OK | |
| 4. RECONFIRM DTC |
Clear the DTC (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | ||
| ||
| 5. CHECK FRONT SPEED SENSOR INSTALLATION |
Turn the ignition switch off.
Check the speed sensor installation (Click here).

Text in Illustration *1
Front Speed Sensor
*a
No clearance
*b
OK
*c
NG
- OK:
- There is no clearance between the sensor and the front steering knuckle.
- The installation bolt is tightened properly.
|
|
||||
| OK | |
| 6. CHECK FRONT SPEED SENSOR TIP |
Remove the front speed sensor (Click here).
Check the speed sensor tip.
- OK:
- No scratches, oil, or foreign matter on the sensor tip.
- NOTICE:
- If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
|
|
||||
| OK | |
| 7. CHECK FRONT SPEED SENSOR ROTOR |
Remove the front axle with ABS rotor bearing assembly (Click here).
Check the speed sensor rotor.
- OK:
- No scratches, oil, or foreign matter on the rotors.
- HINT:
- The front speed sensor rotor is incorporated into the front axle with ABS rotor bearing assembly.
- If the front speed sensor rotor needs to be replaced, replace it together with the front axle with ABS rotor bearing assembly.
|
|
||||
| OK | |
| 8. INSPECT SKID CONTROL SENSOR WIRE |
Turn the ignition switch off.
Make sure that there is no looseness at the locking parts and connecting parts of the connectors.
Remove the skid control sensor wire (Click here).
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
for RH Tester Connection
Condition
Specified Condition
Ap1-1 - p1-1 (FR-)
Always
Below 1 Ω
Ap1-2 - p1-2 (FR+)
Always
Below 1 Ω
Ap1-1 - Ap1-2
Always
10 kΩ or higher
for LH Tester Connection
Condition
Specified Condition
Ap2-1 - p2-1 (FL-)
Always
Below 1 Ω
Ap2-2 - p2-2 (FL+)
Always
Below 1 Ω
Ap2-1 - Ap2-2
Always
10 kΩ or higher
Text in Illustration *A
for RH
*B
for LH
*1
Skid Control Sensor Wire
|
|
||||
| OK | |
| 9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
Install the skid control sensor wire.
Disconnect the A6 skid control ECU connector.
Disconnect the p1 and/or p2 speed sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RH Tester Connection
Condition
Specified Condition
A6-7 (FR+) - p1-2 (FR+)
Always
Below 1 Ω
A6-7 (FR+) - Body ground
Always
10 kΩ or higher
A6-6 (FR-) - p1-1 (FR-)
Always
Below 1 Ω
A6-6 (FR-) - Body ground
Always
10 kΩ or higher
- for LH:
Tester Connection
Condition
Specified Condition
A6-19 (FL+) - p2-2 (FL+)
Always
Below 1 Ω
A6-19 (FL+) - Body ground
Always
10 kΩ or higher
A6-18 (FL-) - p2-1 (FL-)
Always
Below 1 Ω
A6-18 (FL-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 10. CHECK TERMINAL VOLTAGE (FR+, FL+) |
Connect the A6 skid control ECU connector.
Disconnect the p1 and/or p2 speed sensor connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
for RH Tester Connection
Switch Condition
Specified Condition
p1-2 (FR+) - Body ground
Ignition switch ON
8 to 14 V
for LH Tester Connection
Switch Condition
Specified Condition
p2-2 (FL+) - Body ground
Ignition switch ON
8 to 14 V
Text in Illustration *A
for RH
*B
for LH
*a
Front view of wire harness connector
(to Front Speed Sensor)
|
|
||||
| Ok | |
| 11. RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | ||
| ||
| 12. REPLACE FRONT SPEED SENSOR |
Turn the ignition switch off.
Replace the front speed sensor (Click here).
| NEXT | |
| 13. RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | ||
| ||
