2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

B15C3 Speaker Output Short

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.
DTC Code
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Speakers
  2. Harness or connector
  3. Stereo component amplifier assembly
  4. Navigation receiver assembly

WIRING DIAGRAM

E286140E01
E286141E01
E286142E01
E286143E01

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    No DTCs are output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK VEHICLE CONDITION
  1. Check the vehicle condition.

    Result 
    Result
    Proceed to
    for JBL Made
    A
    except JBL Made
    B



B
Go to step 13
A


3. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the J4*1 and/or K3*2 front No. 1 speaker assembly connector.

  1. Disconnect the H10*1 and/or H13*2 front No. 2 speaker assembly connector.

  1. Disconnect the H21*1 and/or H22*2 front No. 3 speaker assembly connector.

  1. Disconnect the H14 front No. 4 speaker assembly connector.

  1. Disconnect the L1*1 and/or M1*2 rear speaker set connector.

  1. Disconnect the L3*1 and/or M3*2 rear No. 2 speaker assembly connector.

  1. Disconnect the Q15*1 and/or R13*2 rear header speaker assembly connector.

  1. Disconnect the R24 No. 1 speaker with box assembly connector.

  1. Disconnect the H65 and H66 stereo component amplifier assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H65-4 (FR+) - H21-1 (TWR+)*1
    Always
    Below 1 Ω
    H65-10 (FR-) - H21-2 (TWR-)*1
    Always
    Below 1 Ω
    H21-3 (+) - H10-2*1
    Always
    Below 1 Ω
    H21-4 (-) - H10-1*1
    Always
    Below 1 Ω
    H66-10 (WFR+) - J4-1*1
    Always
    Below 1 Ω
    H66-9 (WFR-) - J4-2*1
    Always
    Below 1 Ω
    H65-3 (FL+) - H22-1 (TWL+)*2
    Always
    Below 1 Ω
    H65-9 (FL-) - H22-2 (TWL-)*2
    Always
    Below 1 Ω
    H22-3 (+) - H13-2*2
    Always
    Below 1 Ω
    H22-4 (-) - H13-1*2
    Always
    Below 1 Ω
    H65-1 (WF1+) - R24-1 (WF1+)
    Always
    Below 1 Ω
    H65-5 (WF1-) - R24-3 (WF1-)
    Always
    Below 1 Ω
    H65-2 (WF2+) - R24-2 (WF2+)
    Always
    Below 1 Ω
    H65-6 (WF2-) - R24-4 (WF2-)
    Always
    Below 1 Ω
    H66-2 (MR+) - Q15-2*1
    Always
    Below 1 Ω
    H66-7 (MR-) - Q15-1*1
    Always
    Below 1 Ω
    H66-3 (WFL+) - K3-1*2
    Always
    Below 1 Ω
    H66-8 (WFL-) - K3-2*2
    Always
    Below 1 Ω
    H66-5 (RR+) - L3-1 (+TW)*1
    Always
    Below 1 Ω
    H66-12 (RR-) - L3-2 (-TW)*1
    Always
    Below 1 Ω
    L3-3 (+) - L1-1*1
    Always
    Below 1 Ω
    L3-4 (-) - L1-2*1
    Always
    Below 1 Ω
    H66-4 (RL+) - M3-1 (+TW)*2
    Always
    Below 1 Ω
    H66-11 (RL-) - M3-2 (-TW)*2
    Always
    Below 1 Ω
    M3-3 (+) - M1-1*2
    Always
    Below 1 Ω
    M3-4 (-) - M1-2*2
    Always
    Below 1 Ω
    H66-1 (ML+) - R13-2*2
    Always
    Below 1 Ω
    H66-6 (ML-) - R13-1*2
    Always
    Below 1 Ω
    H65-8 (CTR+) - H14-2
    Always
    Below 1 Ω
    H66-7 (CTR-) - H14-1
    Always
    Below 1 Ω
    H65-4 (FR+) - Body ground*1
    Always
    10 kΩ or higher
    H65-10 (FR-) - Body ground*1
    Always
    10 kΩ or higher
    H21-3 (+) - Body ground*1
    Always
    10 kΩ or higher
    H21-4 (-) - Body ground*1
    Always
    10 kΩ or higher
    H66-10 (WFR+) - Body ground*1
    Always
    10 kΩ or higher
    H66-9 (WFR-) - Body ground*1
    Always
    10 kΩ or higher
    H65-3 (FL+) - Body ground*2
    Always
    10 kΩ or higher
    H65-9 (FL-) - Body ground*2
    Always
    10 kΩ or higher
    H22-3 (+) - Body ground*2
    Always
    10 kΩ or higher
    H22-4 (-) - Body ground*2
    Always
    10 kΩ or higher
    H65-1 (WF1+) - Body ground
    Always
    10 kΩ or higher
    H65-5 (WF1-) - Body ground
    Always
    10 kΩ or higher
    H65-2 (WF2+) - Body ground
    Always
    10 kΩ or higher
    H65-6 (WF2-) - Body ground
    Always
    10 kΩ or higher
    H66-2 (MR+) - Body ground*1
    Always
    10 kΩ or higher
    H66-7 (MR-) - Body ground*1
    Always
    10 kΩ or higher
    H66-3 (WFL+) - Body ground*2
    Always
    10 kΩ or higher
    H66-8 (WFL-) - Body ground*2
    Always
    10 kΩ or higher
    H66-5 (RR+) - Body ground*1
    Always
    10 kΩ or higher
    H66-12 (RR-) - Body ground*1
    Always
    10 kΩ or higher
    L3-3 (+) - Body ground*1
    Always
    10 kΩ or higher
    L3-4 (-) - Body ground*1
    Always
    10 kΩ or higher
    H66-4 (RL+) - Body ground*2
    Always
    10 kΩ or higher
    H66-11 (RL-) - Body ground*2
    Always
    10 kΩ or higher
    M3-3 (+) - Body ground*2
    Always
    10 kΩ or higher
    M3-4 (-) - Body ground*2
    Always
    10 kΩ or higher
    H66-1 (ML+) - Body ground*2
    Always
    10 kΩ or higher
    H66-6 (ML-) - Body ground*2
    Always
    10 kΩ or higher
    H65-8 (CTR+) - Body ground
    Always
    10 kΩ or higher
    H66-7 (CTR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


5. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Remove the front No. 2 speaker assembly (Click here).

  1. Inspect the front No. 2 speaker assembly (Click here).



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


6. CHECK FRONT NO. 3 SPEAKER ASSEMBLY
  1. Replace the front No. 3 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors that were disconnected to the front No. 3 speaker assemblies.
    2. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 7
OK

END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE)

7. CHECK FRONT NO. 4 SPEAKER ASSEMBLY
  1. Replace the front No. 4 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.



NG
Go to step 8
OK

END (FRONT NO. 4 SPEAKER ASSEMBLY IS DEFECTIVE)

8. INSPECT REAR SPEAKER SET
  1. Remove the rear speaker set with a known good one (Click here).

  1. Inspect the rear speaker set with a known good one (Click here).



NG
REPLACE REAR SPEAKER SET (Click here)
OK


9. CHECK REAR NO. 2 SPEAKER ASSEMBLY
  1. Replace the rear No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors that were disconnected to the rear No. 2 speaker assemblies.
    2. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 10
OK

END (REAR NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

10. CHECK REAR HEADER SPEAKER ASSEMBLY
  1. Replace the rear header speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors that were disconnected to the rear header speaker assemblies.
    2. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 11
OK

END (REAR HEADER SPEAKER ASSEMBLY IS DEFECTIVE)

11. INSPECT NO. 1 SPEAKER WITH BOX ASSEMBLY
  1. Remove the No. 1 speaker with box assembly (Click here).

  1. Inspect the No. 1 speaker with box assembly (Click here).



NG
REPLACE NO. 1 SPEAKER WITH BOX ASSEMBLY (Click here)
OK


12. CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

13. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the J4*1 and/or K3*2 front No. 1 speaker assembly connector.

  1. Disconnect the H10*1 and/or H13*2 front No. 2 speaker assembly connector.

  1. Disconnect the H21*1 and/or H22*2 front No. 3 speaker assembly connector.

  1. Disconnect the H14 front No. 4 speaker assembly connector.

  1. Disconnect the L1*1 and/or M1*2 rear speaker set connector.

  1. Disconnect the L3*1 and/or M3*2 rear No. 2 speaker assembly connector.

  1. Disconnect the Q15*1 and/or R13*2 rear header speaker assembly connector.

  1. Disconnect the R24 No. 1 speaker with box assembly connector.

  1. Disconnect the H67 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H67-13 (FR+) - H21-1 (TWR+)*1
    Always
    Below 1 Ω
    H67-28 (FR-) - H21-2 (TWR-)*1
    Always
    Below 1 Ω
    H21-3 (+) - H10-2*1
    Always
    Below 1 Ω
    H21-4 (-) - H10-1*1
    Always
    Below 1 Ω
    H67-5 (WFR+) - J4-1*1
    Always
    Below 1 Ω
    H67-20 (WFR-) - J4-2*1
    Always
    Below 1 Ω
    H67-12 (FL+) - H22-1 (TWL+)*2
    Always
    Below 1 Ω
    H67-27 (FL-) - H22-2 (TWL-)*2
    Always
    Below 1 Ω
    H22-3 (+) - H13-2*2
    Always
    Below 1 Ω
    H22-4 (-) - H13-1*2
    Always
    Below 1 Ω
    H67-6 (WF1+) - R24-1 (WF1+)
    Always
    Below 1 Ω
    H67-21 (WF1-) - R24-3 (WF1-)
    Always
    Below 1 Ω
    H67-9 (MR+) - Q15-2*1
    Always
    Below 1 Ω
    H67-24 (MR-) - Q15-1*1
    Always
    Below 1 Ω
    H67-4 (WFL+) - K3-1*2
    Always
    Below 1 Ω
    H67-19 (WFL-) - K3-2*2
    Always
    Below 1 Ω
    H67-15 (RR+) - L3-1 (+TW)*1
    Always
    Below 1 Ω
    H67-30 (RR-) - L3-2 (-TW)*1
    Always
    Below 1 Ω
    L3-3 (+) - L1-1*1
    Always
    Below 1 Ω
    L3-4 (-) - L1-2*1
    Always
    Below 1 Ω
    H67-14 (RL+) - M3-1 (+TW)*2
    Always
    Below 1 Ω
    H67-29 (RL-) - M3-2 (-TW)*2
    Always
    Below 1 Ω
    M3-3 (+) - M1-1*2
    Always
    Below 1 Ω
    M3-4 (-) - M1-2*2
    Always
    Below 1 Ω
    H67-8 (ML+) - R13-2*2
    Always
    Below 1 Ω
    H67-23 (ML-) - R13-1*2
    Always
    Below 1 Ω
    H67-7 (CTR+) - H14-2
    Always
    Below 1 Ω
    H67-22 (CTR-) - H14-1
    Always
    Below 1 Ω
    H67-13 (FR+) - Body ground*1
    Always
    10 kΩ or higher
    H67-28 (FR-) - Body ground*1
    Always
    10 kΩ or higher
    H21-3 (+) - Body ground*1
    Always
    10 kΩ or higher
    H21-4 (-) - Body ground*1
    Always
    10 kΩ or higher
    H67-5 (WFR+) - Body ground*1
    Always
    10 kΩ or higher
    H67-20 (WFR-) - Body ground*1
    Always
    10 kΩ or higher
    H67-12 (FL+) - Body ground*2
    Always
    10 kΩ or higher
    H67-27 (FL-) - Body ground*2
    Always
    10 kΩ or higher
    H22-3 (+) - Body ground*2
    Always
    10 kΩ or higher
    H22-4 (-) - Body ground*2
    Always
    10 kΩ or higher
    H67-6 (WF1+) - Body ground
    Always
    10 kΩ or higher
    H67-21 (WF1-) - Body ground
    Always
    10 kΩ or higher
    H67-9 (MR+) - Body ground*1
    Always
    10 kΩ or higher
    H67-24 (MR-) - Body ground*1
    Always
    10 kΩ or higher
    H67-4 (WFL+) - Body ground*2
    Always
    10 kΩ or higher
    H67-19 (WFL-) - Body ground*2
    Always
    10 kΩ or higher
    H67-15 (RR+) - Body ground*1
    Always
    10 kΩ or higher
    H67-30 (RR-) - Body ground*1
    Always
    10 kΩ or higher
    L3-3 (+) - Body ground*1
    Always
    10 kΩ or higher
    L3-4 (-) - Body ground*1
    Always
    10 kΩ or higher
    H67-14 (RL+) - Body ground*2
    Always
    10 kΩ or higher
    H67-29 (RL-) - Body ground*2
    Always
    10 kΩ or higher
    M3-3 (+) - Body ground*2
    Always
    10 kΩ or higher
    M3-4 (-) - Body ground*2
    Always
    10 kΩ or higher
    H67-8 (ML+) - Body ground*2
    Always
    10 kΩ or higher
    H67-23 (ML-) - Body ground*2
    Always
    10 kΩ or higher
    H67-7 (CTR+) - Body ground
    Always
    10 kΩ or higher
    H67-22 (CTR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


15. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Remove the front No. 2 speaker assembly (Click here).

  1. Inspect the front No. 2 speaker assembly (Click here).

    OK:
    Malfunction disappears.



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


16. CHECK FRONT NO. 3 SPEAKER ASSEMBLY
  1. Replace the front No. 3 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors that were disconnected to the front No. 3 speaker assemblies.
    2. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 17
OK

END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE)

17. INSPECT FRONT NO. 4 SPEAKER ASSEMBLY
  1. Remove the front No. 4 speaker assembly (Click here).

  1. Inspect the front No. 4 speaker assembly (Click here).



NG
REPLACE FRONT NO. 4 SPEAKER ASSEMBLY (Click here)
OK


18. CHECK REAR SPEAKER SET
  1. Remove the rear speaker set (Click here).

  1. Inspect the rear speaker set (Click here).



NG
REPLACE REAR SPEAKER SET (Click here)
OK


19. INSPECT REAR NO. 2 SPEAKER ASSEMBLY
  1. Remove the rear No. 2 speaker assembly (Click here).

  1. Inspect the rear No. 2 speaker assembly (Click here).



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK


20. CHECK REAR HEADER SPEAKER ASSEMBLY
  1. Remove the rear header speaker assembly (Click here).

  1. Inspect the rear header speaker assembly (Click here).



NG
REPLACE REAR HEADER SPEAKER ASSEMBLY (Click here)
OK


21. CHECK NO. 1 SPEAKER WITH BOX ASSEMBLY
  1. Remove the No. 1 speaker with box assembly (Click here).

  1. Inspect the No. 1 speaker with box assembly (Click here).



NG
REPLACE NO. 1 SPEAKER WITH BOX ASSEMBLY (Click here)
OK


22. CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)


← B15C2 Speed Signal Malfunction (from Aug 2014)B15C3 Speaker Output Short (from Aug 2014) →