Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SECURITY HORN ASSEMBLY (w/ Built-in Battery type)
REMOVAL
Removal / installation · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
1.
PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here ).
2.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here ).
3.
REMOVE REAR NO. 2 SEAT ASSEMBLY
for Manual Seat Type: (Click here )
for Power Seat Type: (Click here )
for Face to Face Seat Type: (Click here )
4.
REMOVE REAR NO. 1 SEATBACK ASSEMBLY
for 60/40 Split Double-folding Seat Type LH Side: (Click here )
for 60/40 Split Double-folding Seat Type RH Side: (Click here )
5.
REMOVE NO. 1 REAR FLOOR STEP COVER (w/ Rear No. 2 Seat)
HINT:
Use the same procedure for all rear No. 1 floor step covers.
Using a screwdriver, detach the 2 claws and remove the rear No. 1 floor step cover.
HINT:
Tape the screwdriver tip before use.
Text in Illustration
*1
Protective Tape
6.
REMOVE QUARTER SCUFF PLATE INNER RH
HINT:
Use the same procedure described for the LH side.
7.
REMOVE REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure described for the LH side.
8.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure described for the LH side.
9.
REMOVE OUTER LAP BELT ANCHOR COVER
HINT:
Use the same procedure for the other outer lap belt anchor cover.
Detach the 3 claws and remove the outer lap belt anchor cover.
10.
REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
Remove the tonneau cover.
11.
REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)
HINT:
Use the same procedure for the other front luggage compartment trim cover.
Detach the 4 claws and remove the cap.
Remove the bolt, luggage hold belt striker and front luggage compartment trim cover.
Text in Illustration
*1
Luggage Hold Belt Striker
12.
REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)
Detach the clip and remove the No. 1 deck board.
13.
REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
Detach the 5 clips and 4 claws and remove the rear floor mat rear support plate.
14.
REMOVE FLOOR SIDE RAIL RH (w/ Deck Rail)
HINT:
Use the same procedure described for the LH side.
15.
REMOVE FLOOR SIDE RAIL LH (w/ Deck Rail)
Remove the 3 bolts and floor side rail.
16.
REMOVE REAR FLOOR CARPET ASSEMBLY
Detach the 4 claws and remove the rear floor carpet.
Text in Illustration
*A
w/o Deck Rail
*B
w/ Deck Rail
*C
for Face to Face Seat Type
-
-
17.
REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER
HINT:
Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.
Detach the 3 claws and remove the rear No. 1 seat outer lap belt anchor cover.
18.
REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
HINT:
Use the same procedure for the other No. 1 luggage compartment trim hook.
Remove the luggage compartment trim hook by turning it clockwise.
19.
REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)
HINT:
Use the same procedure for the other No. 1 tonneau cover holder cap.
Using a screwdriver, detach the 2 claws and remove the No. 1 tonneau cover holder cap.
HINT:
Tape the screwdriver tip before use.
Text in Illustration
*1
Protective Tape
20.
REMOVE FRONT DECK SIDE TRIM COVER RH (w/ Tonneau Cover)
HINT:
Use the same procedure for the other front deck side trim cover.
Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.
HINT:
Tape the screwdriver tip before use.
Text in Illustration
*1
Protective Tape
21.
REMOVE ASSIST GRIP PLUG (w/ Rear No. 2 Seat)
HINT:
Use the same procedure for all assist grip plugs.
Using a screwdriver, detach the 2 claws and remove the assist grip plug.
HINT:
Tape the screwdriver tip before use.
Text in Illustration
*1
Protective Tape
22.
REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)
HINT:
Use the same procedure for the other assist grip.
Remove the 2 bolts and assist grip.
23.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
w/o Rear No. 2 Seat:
Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
Detach the 6 claws and 2 guides and disconnect the rear seatback lock control lever base.
Remove the 4 bolts and screws.
Detach the 5 clips and 8 claws.
Disconnect each connector.
Pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.
w/ Rear No. 2 Seat:
Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.
Remove the 2 bolts and screw.
Detach the 4 clips and 8 claws.
Disconnect each connector and remove the deck trim side panel.
24.
REMOVE REAR SIDE NO. 2 AIR DUCT
Detach the 2 clips.
Detach the clamp and remove the duct.
25.
REMOVE THEFT WARNING SIREN ASSEMBLY (for 5 Door)
Remove the 2 bolts.
Detach the claw and remove the guide.
Disconnect the connector and remove the theft warning siren assembly.
26.
REMOVE REAR SEAT ASSEMBLY (for 3 Door)
for 60/40 Split Tumble Seat Type LH Side: (Click here )
for 60/40 Split Tumble Seat Type RH Side: (Click here )
27.
REMOVE DOOR SCUFF PLATE ASSEMBLY RH (for 3 Door)
HINT:
Use the same procedure described for the LH side.
28.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for 3 Door)
HINT:
Use the same procedure described for the LH side.
29.
REMOVE TONNEAU COVER ASSEMBLY (for 3 Door)
Remove the tonneau cover.
30.
REMOVE MAT SET PLATE COVER (for 3 Door)
HINT:
Use the same procedure for all mat set plate covers.
Using a screwdriver, detach the 2 claws and remove the mat set plate cover.
HINT:
Tape the screwdriver tip before use.
Text in Illustration
*1
Protective tape
31.
REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (for 3 Door)
Remove the 5 screws.
Detach the 6 claws and remove the rear floor mat rear support plate.
32.
REMOVE QUARTER TRIM COVER HOLE (for 3 Door)
Detach the 2 claws and 2 guides and remove the quarter trim cover hole.
33.
REMOVE REAR FLOOR CARPET ASSEMBLY (for 3 Door)
Install the rear floor carpet.
34.
REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for 3 Door)
HINT:
Use the same procedure for the other No. 1 luggage compartment trim hook.
Remove the luggage compartment trim hook by turning it clockwise.
35.
REMOVE NO. 1 TONNEAU COVER HOLDER CAP (for 3 Door)
HINT:
Use the same procedure for the other tonneau cover holder cap.
Using a screwdriver, detach the 2 claws and remove the tonneau cover holder cap.
HINT:
Tape the screwdriver tip before use.
Text in Illustration
*1
Protective tape
36.
REMOVE FRONT DECK SIDE TRIM COVER (for 3 Door)
HINT:
Use the same procedure for the other front deck side trim cover.
Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.
HINT:
Tape the screwdriver tip before use.
Text in Illustration
*1
Protective tape
37.
REMOVE QUARTER TRIM POCKET TRAY (for 3 Door)
Put protective tape around the quarter trim pocket tray.
Using a screwdriver, detach the 6 claws and 2 guides, and remove the quarter trim pocket tray.
HINT:
Tape the screwdriver tip before use.
Text in Illustration
*1
Protective tape
38.
REMOVE OUTER LAP BELT ANCHOR COVER (for 3 Door)
HINT:
Use the same procedure for the other outer lap belt anchor cover.
Detach the 3 claws and remove the outer lap belt anchor cover.
39.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for 3 Door)
Remove the bolt and disconnect the front seat outer belt floor anchor.
Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
Remove the 3 bolts and 2 screws.
Detach the 9 claws and 12 clips.
Disconnect the connector and remove the deck trim side panel.
40.
REMOVE THEFT WARNING SIREN ASSEMBLY (for 3 Door)
Remove the 2 bolts.
Detach the claw and remove the guide.
Disconnect the connector and remove the theft warning siren assembly.