2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Fuel Receiver Gauge Malfunction

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The fuel sender gauge has a variable resistance mechanism. The resistance decreases when the fuel amount increases, and the resistance increases when the fuel amount decreases. The fuel receiver gauge changes based on the resistance of the fuel sender gauge.

WIRING DIAGRAM

E201906E02
E204093E02

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1500 or B1501 is not output
    A
    DTC B1500 is output
    B
    DTC B1501 is output
    C



B
GO TO DTC B1500 (Click here)

C
GO TO DTC B1501 (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL METER)
  1. Operate the intelligent tester according to the display and select Active Test (Click here).

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Fuel Meter Operation
    Fuel receiver gauge
    EMPTY, EMPTY, INDIC, 1/4, 1/2, 3/4, FULL, FULL
    Perform the test with the vehicle stopped and engine idling.

    OK:
    Needle indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR
  1. Disconnect the G6 meter connector.

  1. Disconnect the S5 gauge connector.

  1. Disconnect the t1*1 gauge connector.

  1. Disconnect the R40*2 gauge connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G6-9 (L) - S5-2 (FS)
    Always
    Below 1 Ω
    G6-24 (E) - S5-3 (FE)
    G6-8 (L) - t1-4 (S)*1
    G6-23 (FE) - t1-5 (E)*1
    G6-9 (L) - R40-3 (FS)*2
    G6-24 (E) - R40-1 (FE)*2
    G6-21 (E2) - Body ground
    G6-9 (L) - Body ground
    Always
    10 kΩ or higher
    G6-9 (L) - G6-24 (E)
    G6-8 (L) - Body ground*1
    G6-8 (L) - G6-23 (FE)*1

    1. 1*: for Double Tank Type
    2. 2*: for 3 Door



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4. CHECK ENGINE TYPE
  1. Check the engine type.

    Engine Type 
    Engine type
    Proceed to
    for 1GR-FE
    A
    for 2TR-FE
    B
    for 1KD-FTV
    C
    for 5L-E
    D



B
Go to step 9

C
Go to step 13

D
Go to step 20
A


5. INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for 1GR-FE)
E158805E07
  1. Remove the fuel suction with pump and gauge tube assembly.for 1GR-FE, Single Tank Type: (Click here)for 1GR-FE, Double Tank Type: (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 (FS) - B-2
    Always
    Below 1 Ω
    A-3 (FE) - B-1
    Always
    Below 1 Ω
    A-2 (FS) - A-3 (FE)
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected (Fuel Suction with Pump and Gauge Tube Assembly)
    *b
    Lower side (to Fuel Sender Gauge Assembly)
    *c
    Connector A
    *d
    Connector B
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Single Tank Type)
    B
    NG (for Double Tank Type)
    C



B
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)

C
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)
A


6. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 1GR-FE)

  1. E201786E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector (to Fuel Sender Gauge Assembly)
    *b
    Float Level F (Upper)
    *c
    Float Level E (Lower)
    Result 
    Result
    Proceed to
    OK (for Double Tank Type)
    A
    OK (for Single Tank Type)
    B
    NG (for Single Tank Type)
    C
    NG (for Double Tank Type)
    D



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

D
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
A


7. INSPECT FUEL TANK VENT TUBE ASSEMBLY (for 1GR-FE, DOUBLE TANK TYPE)
E201612E01
  1. Remove the fuel tank vent tube assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
4 (S) - 1
Always
Below 1 Ω
5 (E) - 2
Always
Below 1 Ω
4 (S) - 5 (E)
Always
10 kΩ or higher

Text in Illustration 
*a
Fuel Tank Vent Tube Assembly
*b
Component without harness connected (Fuel Tank Vent Tube Assembly)


NG
REPLACE FUEL TANK VENT TUBE ASSEMBLY (Click here)
OK


8. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 1GR-FE, DOUBLE TANK TYPE)
  1. Remove the fuel sender gauge assembly (Click here).

  1. A223156E02
    Measure the resistance according to the value(s) in the table below.
    Standard Resistance 
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω
    Text in Illustration 
    *a
    Front view of wire harness connector (Fuel Sender Gauge Assembly)
    *b
    Float Level F (Upper)
    *c
    Float Level E (Lower)



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

9. INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for 2TR-FE)

NOTICE:
For 3 door vehicles, proceed to the next step.

  1. Remove the fuel sender gauge.for 2TR-FE, Single Tank Type: (Click here)for 2TR-FE, Double Tank Type: (Click here)

  1. E158805E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 (FS) - B-2
    Always
    Below 1 Ω
    A-3 (FE) - B-1
    Always
    Below 1 Ω
    A-2 (FS) - A-3 (FE)
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected (Fuel Suction with Pump and Gauge Tube Assembly)
    *b
    Lower side (to Fuel Sender Gauge Assembly)
    *c
    Connector A
    *d
    Connector B
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Single Tank Type)
    B
    NG (for Double Tank Type)
    C



B
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)

C
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)
A


10. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 2TR-FE)
E201786E01
for 3 door:
  1. Remove the fuel sender gauge (Click here).

  1. A223162E02
    Measure the resistance according to the value(s) in the table below.
    Standard Resistance 
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω
    Text in Illustration 
    *a
    Component without harness connected (Fuel Sender Gauge Assembly)
    *b
    Float Level F (Upper)
    *c
    Float Level E (Lower)

for 5 door:
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance 
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω
    Text in Illustration 
    *a
    Front view of wire harness connector (Fuel Sender Gauge Assembly)
    *b
    Float Level F (Upper)
    *c
    Float Level E (Lower)
    Result 
    Result
    Proceed to
    OK (for Double Tank Type)
    A
    OK (for Single Tank Type)
    B
    NG (for Single Tank Type)
    C
    NG (for Double Tank Type)
    D



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

D
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
A


11. INSPECT FUEL TANK VENT TUBE ASSEMBLY (for 2TR-FE, DOUBLE TANK TYPE)
  1. Remove the fuel tank vent tube assembly (Click here).

  1. E201612E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (S) - 1
    Always
    Below 1 Ω
    5 (E) - 2
    Always
    Below 1 Ω
    4 (S) - 5 (E)
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Fuel tank vent tube assembly
    *b
    Component without harness connected (Fuel Tank Vent Tube Assembly)



NG
REPLACE FUEL TANK VENT TUBE ASSEMBLY (Click here)
OK


12. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 2TR-FE, DOUBLE TANK TYPE)
  1. Remove the fuel sender gauge assembly (Click here).

  1. A223156E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω

    Text in Illustration 
    *a
    Fuel Sender Gauge Assembly
    *b
    Float Level F (Upper)
    *c
    Float Level E (Lower)



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

13. CHECK FUEL TANK TYPE
  1. Check the fuel tank type.

    Fuel Tank Type 
    Fuel Tank Type
    Proceed to
    Single Tank Type
    A
    Double Tank Type
    B



B
Go to step 16
A


14. INSPECT FUEL TANK VENT TUBE ASSEMBLY (for 1KD-FTV, SINGLE TANK TYPE)

NOTICE:
For 3 door vehicles, proceed to the next step.

  1. Remove the fuel sender gauge.for 1KD-FTV, Single Tank Type: (Click here)

  1. E158805E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 (FS) - B-2
    Always
    Below 1 Ω
    A-3 (FE) - B-1
    Always
    Below 1 Ω
    A-2 (FS) - A-3 (FE)
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected (Fuel Tank Vent Tube Assembly)
    *b
    Lower side (to Fuel Sender Gauge Assembly)
    *c
    Connector A
    *d
    Connector B



NG
REPLACE FUEL TANK VENT TUBE ASSEMBLY (Click here)
OK


15. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 1KD-FTV, SINGLE TANK TYPE)
A223162E02
E201786E01
for 3 door:
  1. Remove the fuel sender gauge (Click here).

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance 
Tester Connection
Condition
Specified Condition
1 - 3
Float level is F
12 to 18 Ω
Float level is E
405 to 415 Ω
Text in Illustration 
*a
Component without harness connected (Fuel Sender Gauge Assembly)
*b
Float Level F (Upper)
*c
Float Level E (Lower)
for 5 door:
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance 
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω
    Text in Illustration 
    *a
    Front view of wire harness connector (Fuel Sender Gauge Assembly)
    *b
    Float Level F (Upper)
    *c
    Float Level E (Lower)



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

16. INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for 1KD-FTV, DOUBLE TANK TYPE)
  1. Remove the fuel sender gauge.for 1KD-FTV, Double Tank Type: (Click here)

  1. E158805E07
    Measure the resistance according to the value(s) in the table below.
    Standard Resistance 
    Tester Connection
    Condition
    Specified Condition
    A-2 (FS) - B-2
    Always
    Below 1 Ω
    A-3 (FE) - B-1
    Always
    Below 1 Ω
    A-2 (FS) - A-3 (FE)
    Always
    10 kΩ or higher
    Text in Illustration 
    *a
    Component without harness connected (Fuel Suction with Pump and Gauge Tube Assembly)
    *b
    Lower side (to Fuel Sender Gauge Assembly)
    *c
    Connector A
    *d
    Connector B



NG
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)
OK


17. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 1KD-FTV, DOUBLE TANK TYPE)

  1. E201786E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector (to Fuel Sender Gauge Assembly)
    *b
    Float Level F (Upper)
    *c
    Float Level E (Lower)



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
OK


18. INSPECT FUEL TANK VENT TUBE ASSEMBLY (for 1KD-FTV, DOUBLE TANK TYPE)
  1. Remove the fuel tank vent tube assembly (Click here).

  1. E201612E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (S) - 1
    Always
    Below 1 Ω
    5 (E) - 2
    Always
    Below 1 Ω
    4 (S) - 5 (E)
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Fuel Tank Vent Tube Assembly
    *b
    Component without harness connected (Fuel Tank Vent Tube Assembly)



NG
REPLACE FUEL TANK VENT TUBE ASSEMBLY (Click here)
OK


19. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 1KD-FTV, DOUBLE TANK TYPE)
  1. Remove the fuel sender gauge assembly (Click here).

  1. A223156E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω

    Text in Illustration 
    *a
    Fuel Sender Gauge Assembly
    *b
    Float Llevel F (Upper)
    *c
    Float Level E (Lower)



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

20. INSPECT FUEL TANK VENT TUBE ASSEMBLY (for 5L-E)
  1. Remove the fuel sender gauge. for 5L-E, Single Tank Type: (Click here)for 5L-E, Double Tank Type: (Click here)

  1. E158805E07
    Measure the resistance according to the value(s) in the table below.
    Standard Resistance 
    Tester Connection
    Condition
    Specified Condition
    A-2 (FS) - B-2
    Always
    Below 1 Ω
    A-3 (FE) - B-1
    Always
    Below 1 Ω
    A-2 (FS) - A-3 (FE)
    Always
    10 kΩ or higher
    Text in Illustration 
    *a
    Component without harness connected (Fuel Suction with Pump and Gauge Tube Assembly)
    *b
    Lower side (to Fuel Sender Gauge Assembly)
    *c
    Connector A
    *d
    Connector B
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Single Tank Type)
    B
    NG (for Double Tank Type)
    C



B
REPLACE FUEL TANK VENT TUBE ASSEMBLY (Click here)

C
REPLACE FUEL TANK VENT TUBE ASSEMBLY (Click here)
A


21. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 5L-E)

  1. E201786E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector (to Fuel Sender Gauge Assembly)
    *b
    Float level F (upper)
    *c
    Float level E (lower)
    Result 
    Result
    Proceed to
    OK (for Double Tank Type)
    A
    OK (for Single Tank Type)
    B
    NG (for Single Tank Type)
    C
    NG (for Double Tank Type)
    D



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

D
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
A


22. INSPECT FUEL TANK VENT TUBE ASSEMBLY (for 5L-E, DOUBLE TANK TYPE)
  1. Remove the fuel tank vent tube assembly (Click here).

  1. E201612E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (S) - 1
    Always
    Below 1 Ω
    5 (E) - 2
    Always
    Below 1 Ω
    4 (S) - 5 (E)
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Fuel Tank Vent Tube Assembly
    *b
    Component without harness connected (Fuel Tank Vent Tube Sub-assembly)



NG
REPLACE FUEL TANK VENT TUBE ASSEMBLY (Click here)
OK


23. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 5L-E, DOUBLE TANK TYPE)
  1. Remove the fuel sender gauge assembly (Click here).

  1. A223156E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω

    Text in Illustration 
    *a
    Fuel Sender Gauge Assembly
    *b
    Float level F (upper)
    *c
    Float level E (lower)



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Fuel Receiver Gauge Malfunction (Aug 2013 – Jul 2014)Engine Coolant Temperature Receiver Gauge Malfunction (Aug 2013 – Jul 2014) →