C1403 Rear Speed Sensor RH Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Also covers:
- C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1274 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)
- C1404 Rear Speed Sensor LH Malfunction
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Refer to DTCs C1401 and C1402 (Click here).| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1403 C1404 |
One of the following conditions is met:
|
|
| C1273 C1274 |
Detect only during test mode. |
|
- HINT:
- DTC C1403 is for the rear speed sensor RH.
- DTC C1404 is for the rear speed sensor LH.
- DTC C1403 is for the rear speed sensor RH.
INSPECTION PROCEDURE
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
| 1. CHECK REAR SPEED SENSOR INSTALLATION |
Check the speed sensor installation (Click here).

Text in Illustration *1
Rear Speed Sensor
*a
No clearance
*b
OK
*c
NG
- OK:
- There is no clearance between the sensor and the rear axle carrier.
- The installation nut is tightened properly.
|
|
||||
| OK | |
| 2. CHECK REAR SPEED SENSOR TIP |
Remove the rear speed sensor (Click here).
Check the speed sensor tip.
- OK:
- No scratches, oil, or foreign matter on the sensor tip.
- NOTICE:
- If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
|
|
||||
| OK | |
| 3. CHECK REAR SPEED SENSOR ROTOR |
Remove the rear axle hub and bearing assembly (Click here).
Check the speed sensor rotor.
- OK:
- No scratches, oil, or foreign matter on the rotors.
- HINT:
- The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
- If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED) |
Turn the ignition switch off
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Wheel Speed
Rear speed sensor RH value/ min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Changes continuously during acceleration/deceleration.
RL Wheel Speed
Rear speed sensor LH value/ min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Changes continuously during acceleration/deceleration.
Check the speed value output from the speed sensor displayed on the intelligent tester.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
|
|
||||
| OK | ||
| ||
| 5. REPLACE REAR SPEED SENSOR |
Turn the ignition switch off.
Replace the rear speed sensor (Click here).
| NEXT | |
| 6. RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
- HINT:
- The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
- If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.
|
|
||||
| A | ||
| ||
