2013-2015 Land Cruiser Prado · Service Manual Brake

C1415 Rear Speed Sensor RH Output Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTCs C1401 and C1402 (Click here).
DTC Code
DTC Detection Condition
Trouble Area
C1415
C1416
One of the following conditions is met:
  1. An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.
  2. At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.
  3. At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.
  1. Rear speed sensor RH/LH
  2. Rear skid control sensor wire
  3. Speed sensor circuit
  4. Rear speed sensor rotor RH/LH
  5. Master cylinder solenoid (Skid control ECU)
C1277
C1278
Stored only during test mode.
  1. Rear speed sensor RH/LH
  2. Rear speed sensor rotor RH/LH

HINT:
  1. DTCs C1415 and C1277 are for the rear speed sensor RH.
  2. DTCs C1416 and C1278 are for the rear speed sensor LH.


WIRING DIAGRAM

Refer to DTCs C1407 and C1408 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform calibration (Click here).
  2. Check the speed sensor signal after cleaning or replacement (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Speed Open
    Rear speed sensor RH open detection/ Error or Normal
    Normal
    -
    RL Speed Open
    Rear speed sensor LH open detection/ Error or Normal
    Normal
    -

    OK:
    Normal (there are no momentary interruptions).

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 9
OK


2. READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    Rear speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.
    RL Wheel Speed
    Rear speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 5
OK


3. PERFORM TEST MODE (SIGNAL CHECK)
  1. Turn the ignition switch to ON.

  1. Perform the sensor check in the Test Mode Procedure (Click here).

    OK:
    All test mode DTCs are cleared.



NG
Go to step 5
OK


4. RECONFIRM DTC
  1. Turn the ignition switch to ON.

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
Go to step 12
A

USE SIMULATION METHOD TO CHECK (Click here)

5. CHECK REAR SPEED SENSOR INSTALLATION
  1. Turn the ignition switch off.

  1. C144929E49
    Check the speed sensor installation (Click here).

    OK:
    There is no clearance between the sensor and the rear axle.
    The installation nut is tightened properly.

    Text in Illustration 
    *1
    Rear Speed Sensor
    *a
    No clearance
    *b
    OK
    *c
    NG



NG
INSTALL REAR SPEED SENSOR CORRECTLY
OK


6. INSPECT REAR SPEED SENSOR TIP
  1. Remove the rear speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil, or foreign matter on the sensor tip.

    NOTICE:
    If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.



NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


7. INSPECT REAR SPEED SENSOR ROTOR
  1. Remove the rear axle hub and bearing assembly (Click here).

  1. Check the speed sensor rotor.

    OK:
    No scratches, oil, or foreign matter on the rotors.

    HINT:
    The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
    If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.



NG
CLEAN OR REPLACE REAR SPEED SENSOR ROTOR
OK


8. INSPECT SKID CONTROL SENSOR WIRE
C214499E04
Text in Illustration 
*A
for RH
*B
for LH
*1
Skid Control Sensor Wire
-
-
  1. Remove the skid control sensor wire (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    Sq1-4 - q1-2 (RR+)
    Always
    Below 1 Ω
    Sq1-3 - q1-1 (RR-)
    Always
    Below 1 Ω
    Sq1-4 - Sq1-3
    Always
    10 kΩ or higher
    Sq1-4 - Sq1-1
    Always
    10 kΩ or higher
    Sq1-4 - Sq1-2
    Always
    10 kΩ or higher
    for LH 
    Tester Connection
    Condition
    Specified Condition
    Sq1-2 - q2-2 (RL+)
    Always
    Below 1 Ω
    Sq1-1 - q2-1 (RL-)
    Always
    Below 1 Ω
    Sq1-2 - Sq1-1
    Always
    10 kΩ or higher
    Sq1-2 - Sq1-3
    Always
    10 kΩ or higher
    Sq1-2 - Sq1-4
    Always
    10 kΩ or higher



NG
REPLACE SKID CONTROL SENSOR WIRE (Click here)
OK


9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
  1. Install the skid control sensor wire.

  1. Disconnect the A7 skid control ECU connector.

  1. Disconnect the q1 and/or q2 speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    A7-5 (RR+) - q1-2 (RR+)
    Always
    Below 1 Ω
    A7-5 (RR+) - Body ground
    Always
    10 kΩ or higher
    A7-19 (RR-) - q1-1 (RR-)
    Always
    Below 1 Ω
    A7-19 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH 
    Tester Connection
    Condition
    Specified Condition
    A7-20 (RL+) - q2-2 (RL+)
    Always
    Below 1 Ω
    A7-20 (RL+) - Body ground
    Always
    10 kΩ or higher
    A7-6 (RL-) - q2-1 (RL-)
    Always
    Below 1 Ω
    A7-6 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. CHECK TERMINAL VOLTAGE (RR+, RL+)
  1. Disconnect the q1 and/or q2 speed sensor connector.

  1. Connect the A7 skid control ECU connector.

  1. C207217E08
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH 
    Tester Connection
    Switch Condition
    Specified Condition
    q1-2 (RR+) - Body ground
    Ignition switch ON
    11 to 14 V
    for LH 
    Tester Connection
    Switch Condition
    Specified Condition
    q2-2 (RL+) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *A
    for RH
    *B
    for LH
    *a
    Front view of wire harness connector
    (to Rear Speed Sensor)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A


11. RECONFIRM DTC
  1. Turn the ignition switch to ON.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
Go to step 12
A

USE SIMULATION METHOD TO CHECK (Click here)

12. REPLACE REAR SPEED SENSOR
  1. Replace the rear speed sensor (Click here).


NEXT


13. RECONFIRM DTC
  1. Turn the ignition switch to ON.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (Click here)
A

END


← C1415 Rear Speed Sensor RH Output Malfunction (+ C1277, C1278, C1416) (Aug 2013 – Jul 2014)C1417 High Power Supply Voltage Malfunction (Aug 2013 – Jul 2014) →