INSTALLATION
Removal / installation · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
| 1. INSTALL FRONT ENGINE MOUNTING INSULATOR |
Install the 2 front engine mounting insulators with the 2 nuts.
- Torque:
- 76 N*m{ 775 kgf*cm , 56 ft.*lbf }
Attach the clamp and connect the 2 hoses.
| 2. INSTALL ENGINE WIRE |
Install the engine wire to the engine.
| 3. REMOVE ENGINE FROM ENGINE STAND |
Install 2 engine hangers with 2 bolts as shown in the illustration.

- Torque:
- for No. 1 engine hanger:
- 25 N*m{ 255 kgf*cm , 18 ft.*lbf }
- for No. 2 engine hanger:
- 60 N*m{ 612 kgf*cm , 44 ft.*lbf }
Text in Illustration *1
No. 1 Engine Hanger
*2
No. 2 Engine Hanger
- HINT:
- Part No.
No. 1 engine hanger
12284-30020
No. 2 engine hanger
12282-67030
Bolt
91552-81014 and 91642-81030
- NOTICE:
- Install the engine hangers with new bolts.
Attach an engine sling device and hang the engine with a chain block.
Remove the engine from the engine stand.
| 4. INSTALL REAR END PLATE |
Install the rear end plate with the bolt.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
| 5. INSTALL PUMP IMPELLER DRIVE PLATE (for Automatic Transmission) |
Using SST, hold the crankshaft pulley.

- SST
- 09213-58014
09330-00021
Install the flywheel and ring gear, the pump impeller drive plate and the rear drive plate spacer to the crankshaft.

Text in Illustration *1
Flywheel and Ring Gear
*2
Pump Impeller Drive Plate
*3
Rear Drive Plate Spacer
*a
Engine Side
*b
Transmission Side
- NOTICE:
- Align either hole in the pump impeller drive plate and either hole in the rear drive plate spacer with the knock pin of the flywheel and ring gear, and then install the flywheel and ring gear, the pump impeller drive plate and the rear drive plate spacer to the crankshaft.
- HINT:
- As the rear drive plate spacer and pump impeller drive plate are not reversible, be sure to install them in the direction shown in the illustration.
Clean the bolts and their holes.
Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

- Torque:
- 178 N*m{ 1815 kgf*cm , 131 ft.*lbf }
- NOTICE:
- Do not start the engine for at least 1 hour after installation.
| 6. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission) |
Clean the bolts and their holes.
Apply adhesive to 2 or 3 threads at the end of each bolt.
- Adhesive:
- Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Using SST, hold the crankshaft pulley.

- SST
- 09213-58014
09330-00021
Install the flywheel to the crankshaft.
Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.

- Torque:
- 178 N*m{ 1815 kgf*cm , 131 ft.*lbf }
- NOTICE:
- Do not start the engine for at least 1 hour after installation.
| 7. INSTALL CRANKSHAFT PULLEY COVER |
Install the crankshaft pulley cover with the 2 bolts.
- Torque:
- 25 N*m{ 255 kgf*cm , 18 ft.*lbf }
| 8. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission) |
Insert SST into the clutch disc. Then insert SST (together with the clutch disc) into the flywheel to install the clutch disc.

- SST
- 09301-00110
Text in Illustration 

Flywheel Side
- NOTICE:
- Be sure to install the clutch disc so that it is facing in the correct direction.
| 9. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission) |
![]() ![]() |
Align the matchmarks on the clutch cover and flywheel.
Text in Illustration *a
Matchmark
Tighten the 6 bolts uniformly in the order shown in the illustration, starting with the bolt located near the knock pin on the top.
- SST
- 09301-00110
- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
- HINT:
- Move SST up and down, and right and left lightly after checking that the clutch disc assembly is in the center, and then tighten the bolts.
| 10. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission) |
![]() ![]() |
Using a dial indicator with a roller instrument, measure the diaphragm spring tip alignment.
- SST
- 09333-00013
- Maximum non-alignment:
- 0.5 mm (0.0196 in.)
- If the is alignment is more than the maximum, use SST to adjust the diaphragm spring tip alignment.
| 11. INSTALL ENGINE ASSEMBLY |
Slowly lower the engine into the engine compartment.
Install the engine with the 4 bolts and 4 nuts.
- Torque:
- 40 N*m{ 408 kgf*cm , 30 ft.*lbf }
- HINT:
-


- For RHD vehicles only:
- When tightening the nut closer to the rear of the vehicle for the engine mounting bracket on the right side, make sure that the claw (stopper) of the bolt does not protrude past the rear edge of the bracket.
Text in Illustration *1
Claw (Stopper)
*2
Bracket
*a
Correct
*b
Incorrect
Remove the 2 bolts and 2 engine hangers.
| 12. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR |
- HINT:
- Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.
Install the rear No. 1 engine mounting insulator with the 4 bolts.
- Torque:
- 65 N*m{ 663 kgf*cm , 48 ft.*lbf }
| 13. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission) |
| 14. INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for Automatic Transmission) |
Turn the crankshaft to gain access to the installation locations of the 6 torque converter setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.
- Torque:
- 48 N*m{ 489 kgf*cm , 35 ft.*lbf }
- HINT:
- If it is difficult to reach the setting bolts with the wrench, raise or lower the transmission jack until there is sufficient space for the wrench.
- NOTICE:
- Install the black bolt first, and then the 5 silver bolts.
| 15. INSTALL MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission) |
| 16. INSTALL OIL PAN INSULATOR |
Install the oil pan insulator with the 2 bolts.
- Torque:
- 18 N*m{ 178 kgf*cm , 13 ft.*lbf }
| 17. INSTALL PROPELLER SHAFT ASSEMBLY |
Align the matchmarks on the propeller shaft flange and differential flange.
Install the propeller shaft assembly with the 4 washer, 4 bolts and 4 nuts.
- Torque:
- 88 N*m{ 899 kgf*cm , 65 ft.*lbf }
Align the matchmarks on the propeller shaft flange and transfer flange.
Install the propeller shaft assembly with the 4 washers and 4 nuts.
- Torque:
- 88 N*m{ 899 kgf*cm , 65 ft.*lbf }
| 18. INSTALL FRONT PROPELLER SHAFT ASSEMBLY |
Align the matchmarks on the yoke and differential flange.
Install the propeller shaft assembly with the 4 washers, 4 bolts and 4 nuts.
- Torque:
- 88 N*m{ 899 kgf*cm , 65 ft.*lbf }
Align the matchmarks on the yoke and transfer flange.
Install the propeller shaft assembly with the 4 washers and 4 nuts.
- Torque:
- 88 N*m{ 899 kgf*cm , 65 ft.*lbf }
| 19. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
| 20. INSTALL STARTER ASSEMBLY (for 2.2 kW Type) |
for Manual Transmission:
Install the starter assembly with the bolt and nut.- Torque:
- 68 N*m{ 693 kgf*cm , 50 ft.*lbf }
for Automatic Transmission:
Install the starter assembly with the bolt and 2 nuts.- Torque:
- 68 N*m{ 693 kgf*cm , 50 ft.*lbf }
Connect the starter wire with the nut.
- Torque:
- 9.8 N*m{ 100 kgf*cm , 87 in.*lbf }
Connect the starter connector.
Install the terminal cap.
| 21. INSTALL STARTER ASSEMBLY (for 2.7 kW Type) |
for Manual Transmission:
Install the starter assembly with the bolt and nut.- Torque:
- 68 N*m{ 693 kgf*cm , 50 ft.*lbf }
for Automatic Transmission:
Install the starter assembly with the bolt and 2 nuts.- Torque:
- 68 N*m{ 693 kgf*cm , 50 ft.*lbf }
Connect the starter wire with the nut.
- Torque:
- 21 N*m{ 215 kgf*cm , 16 ft.*lbf }
Connect the starter connector.
Install the terminal cap.
| 22. CONNECT ENGINE WIRE |
Attach the grommet to the wire harness support.

Text in Illustration *1
Grommet
*2
Wire Harness Support
Pass the wire harness into the vehicle and install the wire harness support.

Text in Illustration *A
for LHD
*B
for RHD
Connect the 9 connectors and attach the clamp.

Text in Illustration *A
for LHD
*B
for RHD
Install the bolt.

- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
Text in Illustration *A
w/ KDSS
*B
w/o KDSS
Connect the wire harness protector with the bolt.

- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Connect the engine wire with the nut.

- Torque:
- 7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
Install the bolt.

- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
Attach the clamp and connect the connector.

Connect the 4 injection driver connectors.

Attach the 2 claws and install the nut.

- Torque:
- 11 N*m{ 112 kgf*cm , 8 ft.*lbf }
Install the No. 1 relay block cover.
| 23. INSTALL GLOVE COMPARTMENT DOOR SUB-ASSEMBLY |
| 24. CONNECT NO. 2 FUEL HOSE |
Connect the fuel hose to the No. 3 nozzle leakage pipe.
| 25. CONNECT FUEL HOSE |
Connect the fuel hose to the fuel supply pump.
| 26. CONNECT WATER PIPE AND HOSE SUB-ASSEMBLY |
Connect the water pipe and hose with the bolt.
- Torque:
- 26 N*m{ 260 kgf*cm , 19 ft.*lbf }
| 27. CONNECT INLET HEATER WATER HOSE |
Connect the inlet heater water hose.
| 28. INSTALL NO. 4 ENGINE COVER BRACKET |
Install the No. 4 engine cover bracket with the bolt.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
| 29. INSTALL ENGINE COVER BRACKET INSULATOR |
Install the 2 engine cover bracket insulators with the 2 nuts.

- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Text in Illustration *1
Claw
- HINT:
- Make sure that the claws of the engine cover bracket insulators contact the engine cover brackets.
| 30. INSTALL NO. 3 ENGINE COVER BRACKET |
Install the No. 3 engine cover bracket with the 2 nuts.
- Torque:
- 7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
| 31. INSTALL NO. 1 ENGINE COVER BRACKET |
Install the No. 1 engine cover bracket with the bolt.
- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
| 32. CONNECT PRESSURE FEED TUBE ASSEMBLY |
Connect the pressure feed tube and a new gasket with the union bolt.
- Torque:
- 50 N*m{ 510 kgf*cm , 37 ft.*lbf }
Connect the power steering oil pressure switch connector.
| 33. CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY |
Temporarily install the vane pump oil reservoir with the 3 bolts.

Tighten the 3 bolts of the vane pump oil reservoir in the order shown in the illustration.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
| 34. INSTALL FUEL FILTER ASSEMBLY |
| 35. INSTALL NO. 1 INTAKE PIPE |
Connect the No. 1 intake pipe with the No. 1 air hose and install the 2 bolts.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
Tighten the 2 hose clamps of the No. 1 air hose.
- Torque:
- 6.5 N*m{ 66 kgf*cm , 58 in.*lbf }
Connect the 2 connectors to the intake air temperature sensor and throttle position sensor.
Attach the 2 wire harness clamps.
| 36. CONNECT INTERCOOLER AIR HOSE |
Connect the intercooler air hose and tighten the hose clamp.

- Torque:
- 5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
Text in Illustration *a
Front Side of Vehicle
*b
RH Side
- HINT:
- Install the hose clamp so that it is facing the direction shown in the illustration.
| 37. CONNECT NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY |
Connect the No. 4 vacuum transmitting pipe with the bolt.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
| 38. CONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System) |
Connect the cooler compressor with the 4 bolts.
- Torque:
- 25 N*m{ 250 kgf*cm , 18 ft.*lbf }
Connect the compressor connector.
| 39. INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles) |
Install the No. 1 viscous heater bracket with the 4 bolts.
- Torque:
- 45 N*m{ 459 kgf*cm , 33 ft.*lbf }
| 40. INSTALL VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (for Cold Area Specification Vehicles) |
Install the viscous heater with magnet clutch with the 2 bolts.
- Torque:
- 45 N*m{ 459 kgf*cm , 33 ft.*lbf }
Connect the water by-pass hose and water hose.
Connect the viscous heater connector.
| 41. INSTALL COMPRESSOR OUTLET ELBOW |
Install the compressor outlet elbow with the 2 bolts and tighten the hose clamp.
- Torque:
- for bolt:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
- for hose clamp:
- 6.5 N*m{ 66 kgf*cm , 58 in.*lbf }
Install the wire harness bracket with the bolt.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Attach the 3 wire harness clamps.
| 42. INSTALL AIR CLEANER CASE SUB-ASSEMBLY |
Install the air cleaner case sub-assembly with the 3 bolts.
- Torque:
- 12 N*m{ 122 kgf*cm , 9 ft.*lbf }
| 43. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| 44. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
Attach the 4 clamps to install the air cleaner cap sub-assembly.
except Cold Area Specification Vehicles:
Attach the 2 clamps and connect the mass air flow meter connector.
for Cold Area Specification Vehicles:
Attach the 3 clamps and connect the mass air flow meter connector.
| 45. INSTALL NO. 1 AIR CLEANER HOSE |
Install the No. 1 air cleaner hose with the 2 hose clamps.


Text in Illustration *1
No. 1 Air Cleaner Hose
*2
Compressor Inlet Elbow
*3
Air Cleaner Cap
-
-
*a
Upper Side
*b
Front Side of Vehicle
*c
Protrusion
*d
Groove
- NOTICE:
- When installing the No. 1 air cleaner hose, align the protrusion of the No. 1 air cleaner hose with the protrusion of the compressor inlet elbow as shown in the illustration.
- When installing the No. 1 air cleaner hose, align the groove of the No. 1 air cleaner hose with the protrusion of the air cleaner cap as shown in the illustration.
- When installing the No. 1 air cleaner hose, align the protrusion of the No. 1 air cleaner hose with the protrusion of the compressor inlet elbow as shown in the illustration.
Tighten the 2 hose clamps.
- Torque:
- 5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
- NOTICE:
- When tightening the 2 hose clamps, make sure that they are positioned as shown in the illustration.
| 46. INSTALL BATTERY TRAY |
| 47. INSTALL BATTERY |
| 48. INSTALL BATTERY HOLD DOWN CLAMP |
Install the battery hold down clamp with the 2 nuts.
- Torque:
- 6.0 N*m{ 61 kgf*cm , 53 in.*lbf }
| 49. INSTALL RADIATOR ASSEMBLY |
| 50. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
| 51. INSTALL HOOD SUB-ASSEMBLY |
Install the hood with the 8 bolts.

- Torque:
- for bolt A:
- 13 N*m{ 133 kgf*cm , 10 ft.*lbf }
- for bolt B:
- 18 N*m{ 184 kgf*cm , 13 ft.*lbf }
Text in Illustration 

Bolt A


Bolt B
Connect the washer nozzle hose.
| 52. ADD POWER STEERING FLUID |
| 53. ADD MANUAL TRANSMISSION OIL (for Manual Transmission) |
| 54. INSPECT MANUAL TRANSMISSION OIL (for Manual Transmission) |
Park the vehicle on a level surface.
Check that the oil level is between 0 to 5 mm (0 to 0.196 in.) from the bottom lip of the filler plug opening.

- If the result is not as specified, add transmission oil.
- NOTICE:
- Problems may occur when the oil level is too high or low.
- After replacing the oil, drive the vehicle and check the oil level again.
- Problems may occur when the oil level is too high or low.
- If the result is not as specified, add transmission oil.
Inspect for oil leaks when the oil level is low.
- If the result is not as specified, add transmission oil.
- If the result is not as specified, add transmission oil.
Install a new gasket and the filler plug.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 55. ADD ENGINE OIL |
Add new engine oil.
- Standard Oil Grade:
Item
Oil Grade
Oil Viscosity (SAE)
w/ DPF
ACEA C2
(Using engine oil other than ACEA C2 may damage catalytic converter)
- 0W-30
- 5W-30
(0W-30 is best choice for fuel economy and good starting in cold weather)
w/o DPF
G-DLD1, API CF-4, CF or ACEA B1
(You may also use API CE or CD)
- 5W-30
- 10W-30
- 15W-40
- 20W-50
- Standard Capacity:
Item
Specified Condition
Drain and refill without oil filter change
6.7 liters (7.1 US qts, 5.9 Imp. qts)
Drain and refill with oil filter change
7.0 liters (7.4 US qts, 6.2 Imp. qts)
Dry fill
7.5 liters (7.9 US qts, 6.6 Imp. qts)
Install the oil filler cap.
| 56. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 57. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the B line of the reservoir tank.
- Standard Capacity:
Item
Specified Condition
for Automatic Transmission
w/ Rear Heater
14.9 liters (15.7 US qts, 13.1 Imp. qts)
w/o Rear Heater
13.1 liters (13.8 US qts, 11.5 Imp. qts)
for Manual Transmission
w/ Rear Heater
15.0 liters (15.8 US qts, 13.2 Imp. qts)
w/o Rear Heater
13.2 liters (13.9 US qts, 11.6 Imp. qts)
- HINT:
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- Please contact your TOYOTA dealer for further details.
- for Cold Area Specification Vehicles:
Please contact any authorized TOYOTA dealer or repairer or another duly qualified and equipped professional for further details.
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- NOTICE:
- Never use water as a substitute for engine coolant.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Using a wrench, install the vent plug.
- Torque:
- 2.0 N*m{ 20 kgf*cm , 18 in.*lbf }
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
- CAUTION:
- When pressing the radiator hoses:
- Wear protective gloves.
- Be careful as the radiator hoses are hot.
- Keep your hands away from the radiator fan.
- Wear protective gloves.
Stop the engine and wait until the coolant cools down to ambient temperature.
- CAUTION:
- Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
After the coolant cools down, check that the coolant level is at the FULL line.
If the coolant level is below the FULL line, add TOYOTA SLLC to the FULL line.
| 58. BLEED AIR FROM FUEL SYSTEM |
Using the hand pump mounted on the fuel filter cap, bleed air from the fuel system. Continue pumping until the pump resistance increases.

- NOTICE:
- The maximum hand pump pumping speed is 2 strokes per second.
- The hand pump must be pushed with a full stroke during pumping.
- When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
- If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
- If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
- If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use and the engine cannot be started.
- The maximum hand pump pumping speed is 2 strokes per second.
Check if the engine starts.
- NOTICE:
- Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
- Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
- Use a fully-charged battery.
- Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2

Text in Illustration *a
Reference
(Active Test Operation)
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the 5th time.


- HINT:
- When the Active Test "Test the Fuel Leak" is used to change the pump control mode, the actual fuel pressure inside the common rail drops below the target fuel pressure when the Active Test is off, but this is normal and does not indicate a pump malfunction.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
- HINT:
- It is necessary to clear the DTCs as DTC P1604 or P1605 may be stored when air is bled from the fuel system after replacing or repairing fuel system parts.
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
- OK:
- No DTCs are output.
| 59. ADD AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission) |
| 60. PERFORM REGISTRATION |
Perform registration of the injector compensation codes (Click here).
Perform pilot quantity learning (Click here).
| 61. PERFORM INITIALIZATION |
Perform initialization of the crank time compensation reset function (Click here).
| 62. INSPECT FOR COOLANT LEAK |
- NOTICE:
- Before each inspection, turn the A/C switch off.
- CAUTION:
- Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 63. INSPECT FOR POWER STEERING FLUID LEAK |
| 64. INSPECT FOR OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the areas that were worked on.
| 65. INSPECT FOR FUEL LEAK |
Perform the Active Test.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test.
Intelligent Tester Display
Test Part
Control Range
Diagnostic Note
Test the Fuel Leak
Pressurize common rail interior and check for fuel leaks
Stop/Start
- The fuel pressure inside the common rail increases to the specified value and the engine speed increases to 2000 rpm when the Active Test is performed.
- The above conditions are maintained while the Active Test is being performed.
- The fuel pressure inside the common rail increases to the specified value and the engine speed increases to 2000 rpm when the Active Test is performed.
| 66. INSPECT FOR EXHAUST GAS LEAK |
- If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.
| 67. INSPECT ENGINE IDLE SPEED AND MAXIMUM SPEED |
- HINT:
- For more information about the intelligent tester, refer to its operator's manual.
- If an intelligent tester is not available, use a tachometer's tester probe as a substitute.
- For more information about the intelligent tester, refer to its operator's manual.
Connect the intelligent tester to the DLC3.
If a tester is not available, connect the tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.

- SST
- 09843-18040
Text in Illustration *a
Front view of DLC3
Inspect the idle speed.
- HINT:
- Make sure that the engine is warmed up.
- Make sure that the A/C switch is off.
- w/ DPF:
Make sure that PM regeneration is not being performed.
- Make sure that the engine is warmed up.
Start the engine and measure the idle speed.
- Idle Speed:
Item
Specified Condition
for Automatic Transmission
650 to 750 rpm
for Manual Transmission
w/ DPF
650 to 750 rpm
w/o DPF
610 to 710 rpm
Inspect the maximum speed.
Start the engine.
Fully depress the accelerator pedal.
Measure the maximum speed.
- Maximum Speed:
Item
Specified Condition
w/ DPF
4500 to 4700 rpm
w/o DPF
4450 to 4750 rpm
If the tester probe of a tachometer is connected to the DLC3, disconnect the tester probe together with SST from terminal 9 of the DLC3.
Disconnect the intelligent tester from the DLC3.
| 68. INSPECT ENGINE OIL LEVEL |
Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.
If low, check for leakage and add oil up to the full level mark.- NOTICE:
- Do not fill engine oil above the full level mark.
| 69. INSTALL REAR ENGINE UNDER COVER ASSEMBLY |
Install the rear engine under cover with the 4 bolts.
- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
| 70. INSTALL TRANSMISSION UNDER COVER |
Install the transmission under cover with the 2 bolts.
- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
| 71. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY |
Install the No. 1 engine under cover with the 4 bolts.
- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
| 72. INSTALL FRONT BUMPER LOWER COVER |
Install the front bumper lower cover with the clip and 5 bolts.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
| 73. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY |
Attach the 2 No. 1 engine cover hooks to the No. 3 engine cover bracket.

Text in Illustration *1
No. 1 Engine Cover Hook
*2
No. 3 Engine Cover Bracket
Install the 2 nuts.
- Torque:
- 12 N*m{ 122 kgf*cm , 9 ft.*lbf }


