2013-2015 Land Cruiser Prado · Service Manual Brake

Multi-terrain Select Indicator Light Remains ON

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to Multi-terrain Select Indicator Light does not Come ON (Click here).

WIRING DIAGRAM

Refer to Multi-terrain Select Indicator Light does not Come ON (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here).


1. CHECK LIN COMMUNICATION LINE
  1. Use the GTS to check if the LIN communication system is functioning normally.

    Result 
    Result
    Proceed to
    LIN DTC is not output
    A
    LIN DTC is output
    B



B
GO TO LIN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


2. READ VALUE USING GTS (OFF-ROAD GUIDANCE SWITCH AND DIAL SWITCH SIGNAL)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / D-SEAT SW / Data List.

  1. Check the Data List for proper functioning of the multi-terrain select switch (center cluster module switch) and multi-terrain select road mode selector (center cluster module switch).

    D-SEAT SW 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Off-road Guidance Switch
    Multi-terrain select switch/ ON or OFF
    ON: Switch on
    OFF: Switch off
    -
    Dial Switch Signal 1
    Crawl speed selector/Multi-terrain select road mode selector signal 1/ ON or OFF
    Switches between ON and OFF according to the ON/OFF Combination Chart (Click here)
    -
    Dial Switch Signal 2
    Crawl speed selector/Multi-terrain select road mode selector signal 2/ ON or OFF
    -
    Dial Switch Signal 3
    Crawl speed selector/Multi-terrain select road mode selector signal 3/ ON or OFF
    -

    OK:
    The GTS display changes according to multi-terrain select switch (center cluster module switch) and multi-terrain select road mode selector (center cluster module switch) operation.



NG
Go to step 4
OK


3. INSPECT COMBINATION METER ASSEMBLY
  1. Perform an Active Test of the combination meter assembly using the GTS (Click here).

    OK:
    The multi-terrain select indicator light turns on or off in accordance with the Active Test operation.

    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

4. CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - DRIVING SUPPORT SWITCH CONTROL ECU)
  1. Disconnect the G156 center cluster module switch connector.

  1. Disconnect the G162 driving support switch control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G162-8 (MTS) - G156-20 (FRE)
    Always
    Below 1 Ω
    G162-4 (MOD1) - G156-17 (ECU)
    Always
    Below 1 Ω
    G162-11 (MOD3) - G156-19 (DN)
    Always
    Below 1 Ω
    G162-2 (MOD2) - G156-18 (UP)
    Always
    Below 1 Ω
    G156-24 (E) - Body ground
    Always
    Below 1 Ω
    G162-8 (MTS) or G156-20 (FRE) - Body ground
    Always
    10 kΩ or higher
    G162-4 (MOD1) or G156-17 (ECU) - Body ground
    Always
    10 kΩ or higher
    G162-11 (MOD3) or G156-19 (DN) - Body ground
    Always
    10 kΩ or higher
    G162-2 (MOD2) or G156-18 (UP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT CENTER CLUSTER MODULE SWITCH
  1. Remove the center cluster module switch (Click here).

  1. Inspect the multi-terrain select switch (center cluster module switch) and multi-terrain select road mode selector (center cluster module switch) (Click here).



NG
REPLACE CENTER CLUSTER MODULE SWITCH (Click here)
OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU (Click here)


← Multi-terrain Select Indicator Light Remains ON (Aug 2013 – Jul 2014)Multi-terrain Select Indicator Light does not Come ON (Aug 2013 – Jul 2014) →